diff mbox series

[v2,2/2] arm64: dts: fsl: add support for Kontron pitx-imx8m board

Message ID 20210222140756.713-3-heiko.thiery@gmail.com
State Superseded
Headers show
Series add Kontron pITX-imx8m board | expand

Commit Message

Heiko Thiery Feb. 22, 2021, 2:07 p.m. UTC 
The Kontron pitx-imx8m board is based on an i.MX8MQ soc.

Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
---
v2:
 - bring root nodes in alphabetical order
 - remove pinctrl_gpio_keys for pciewake
 - remove pinctrl_sai2 and pinctrl_spdfif1 since it is not used yet

 Thanks to Michael Walle:
 - add pinctrl for regulator-v-3v3-sd
 - add name for regulator swbst
 - add comment about currently unused audio codec
 - put usb_phy entry in correct alphabetical order

 Thanks to Krzysztof Kozlowski:
 - use generic names for pcie-refclk, tpm, fan-controller, sensor
 - remove empty line
 - fix group name to match schema (ecspi2cs -> ecspi2csgrp)


 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../freescale/imx8mq-kontron-pitx-imx8m.dts   | 641 ++++++++++++++++++
 2 files changed, 642 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts

Comments

Fabio Estevam March 2, 2021, 2:43 p.m. UTC | #1 
Hi Heiko,

On Mon, Feb 22, 2021 at 11:08 AM Heiko Thiery <heiko.thiery@gmail.com> wrote:

> +       reg_usdhc2_vmmc: regulator-v-3v3-sd {

reg_usdhc2_vmmc: regulator-usdhc2-vmmc {

> +       tpm_reset: tpm-reset {
> +               compatible = "gpio-reset";

I don't see this compatible string documented.

> +               reset-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
> +               reset-delay-us = <2>;
> +               reset-post-delay-ms = <60>;
> +               #reset-cells = <0>;
> +       };
> +
> +       usb_hub_reset: usb-hub-reset {
> +               compatible = "gpio-reset";

Same here.

> +&fec1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_fec1>;
> +       phy-mode = "rgmii-id";
> +       phy-handle = <&ethphy0>;
> +       phy-reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;

This property is deprecated. Please consider using reset-gpios inside
ethernet-phy instead.

> +       /* TODO: configure audio, as of now just put a placeholder */
> +       wm8904: audio-codec@1a {
> +               compatible = "wlf,wm8904";
> +               reg = <0x1a>;
> +               clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
> +               clock-names = "mclk";
> +               clock-frequency = <24000000>;

Not a valid property.

> +/* M.2 B-key slot */
> +&pcie0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_pcie0>;
> +       disable-gpio = <&gpio5 29 GPIO_ACTIVE_LOW>;

Not a valid property.

> +       reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
> +       clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
> +                <&clk IMX8MQ_CLK_PCIE1_AUX>,
> +                <&clk IMX8MQ_CLK_PCIE1_PHY>,
> +                <&pcie0_refclk>;
> +       clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
> +       ext_osc = <1>;

Not a valid property.

> +/* Intel Ethernet Controller I210/I211 */
> +&pcie1 {
> +       clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
> +                <&clk IMX8MQ_CLK_PCIE2_AUX>,
> +                <&clk IMX8MQ_CLK_PCIE2_PHY>,
> +                <&pcie1_refclk>;
> +       clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
> +       ext_osc = <1>;

Not a valid property.
Heiko Thiery March 3, 2021, 12:54 p.m. UTC | #2 
Hi Fabio,


Am Di., 2. März 2021 um 15:43 Uhr schrieb Fabio Estevam <festevam@gmail.com>:
>

> Hi Heiko,

>

> On Mon, Feb 22, 2021 at 11:08 AM Heiko Thiery <heiko.thiery@gmail.com> wrote:

>

> > +       reg_usdhc2_vmmc: regulator-v-3v3-sd {

>

> reg_usdhc2_vmmc: regulator-usdhc2-vmmc {


I used the same name as used on imx8mq-evk. Do you think a better name
is the one you proposed?

> > +       tpm_reset: tpm-reset {

> > +               compatible = "gpio-reset";

>

> I don't see this compatible string documented.


This comes from the linux-imx tree [1].  Nethertheless the reset seems
not to be used by the tpm driver for the infineon chip.

[1] https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/reset/gpio-reset.c?h=imx_5.4.70_2.3.0

So I think I can remove it here.

>

> > +               reset-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;

> > +               reset-delay-us = <2>;

> > +               reset-post-delay-ms = <60>;

> > +               #reset-cells = <0>;

> > +       };

> > +

> > +       usb_hub_reset: usb-hub-reset {

> > +               compatible = "gpio-reset";

>

> Same here.


Also the usb-hub-reset can be removed.

>

> > +&fec1 {

> > +       pinctrl-names = "default";

> > +       pinctrl-0 = <&pinctrl_fec1>;

> > +       phy-mode = "rgmii-id";

> > +       phy-handle = <&ethphy0>;

> > +       phy-reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;

>

> This property is deprecated. Please consider using reset-gpios inside

> ethernet-phy instead.


Done

> > +       /* TODO: configure audio, as of now just put a placeholder */

> > +       wm8904: audio-codec@1a {

> > +               compatible = "wlf,wm8904";

> > +               reg = <0x1a>;

> > +               clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;

> > +               clock-names = "mclk";

> > +               clock-frequency = <24000000>;

>

> Not a valid property.


The whole node is removed since v3.

> > +/* M.2 B-key slot */

> > +&pcie0 {

> > +       pinctrl-names = "default";

> > +       pinctrl-0 = <&pinctrl_pcie0>;

> > +       disable-gpio = <&gpio5 29 GPIO_ACTIVE_LOW>;

>

> Not a valid property.


This comes from the linux-imx tree [2]. but in mainline it is not
valid. So I will remove it.

[2] https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/pci/controller/dwc/pci-imx6.c?h=imx_5.4.70_2.3.0#n2436

> > +       reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;

> > +       clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,

> > +                <&clk IMX8MQ_CLK_PCIE1_AUX>,

> > +                <&clk IMX8MQ_CLK_PCIE1_PHY>,

> > +                <&pcie0_refclk>;

> > +       clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";

> > +       ext_osc = <1>;

>

> Not a valid property.


This comes from the linux-imx tree [3]. but in mainline it is not
valid. So I will remove it.

[3] https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/pci/controller/dwc/pci-imx6.c?h=imx_5.4.70_2.3.0#n2422

> > +/* Intel Ethernet Controller I210/I211 */

> > +&pcie1 {

> > +       clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,

> > +                <&clk IMX8MQ_CLK_PCIE2_AUX>,

> > +                <&clk IMX8MQ_CLK_PCIE2_PHY>,

> > +                <&pcie1_refclk>;

> > +       clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";

> > +       ext_osc = <1>;

>

> Not a valid property.


same as commented before.

Thank you for the review. I will prepare v4.


--
Heiko
Fabio Estevam March 3, 2021, 1 p.m. UTC | #3 
Hi Heiko,

On Wed, Mar 3, 2021 at 9:54 AM Heiko Thiery <heiko.thiery@gmail.com> wrote:

> > reg_usdhc2_vmmc: regulator-usdhc2-vmmc {

>

> I used the same name as used on imx8mq-evk. Do you think a better name

> is the one you proposed?


Yes, the way I proposed is the preferred one. Thanks
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6438db3822f8..9fc2c6f64407 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -47,6 +47,7 @@  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-kontron-pitx-imx8m.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
new file mode 100644
index 000000000000..82364e394ed2
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
@@ -0,0 +1,641 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree File for the Kontron pitx-imx8m board.
+ *
+ * Copyright (C) 2021 Heiko Thiery <heiko.thiery@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx8mq.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	model = "Kontron pITX-imx8m";
+	compatible = "kontron,pitx-imx8m", "fsl,imx8mq";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		spi0 = &qspi0;
+		spi1 = &ecspi2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	pcie0_refclk: clock-pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	pcie1_refclk: clock-pcie1-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_usdhc2_vmmc: regulator-v-3v3-sd {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2>;
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_SD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		off-on-delay-us = <20000>;
+		enable-active-high;
+	};
+
+	tpm_reset: tpm-reset {
+		compatible = "gpio-reset";
+		reset-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <2>;
+		reset-post-delay-ms = <60>;
+		#reset-cells = <0>;
+	};
+
+	usb_hub_reset: usb-hub-reset {
+		compatible = "gpio-reset";
+		reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <3000>;
+		reset-post-delay-ms = <50>;
+		#reset-cells = <0>;
+	};
+};
+
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	tpm@0 {
+		compatible = "infineon,slb9670";
+		reg = <0>;
+		resets = <&tpm_reset>;
+		spi-max-frequency = <43000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	phy-reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze100";
+		fsl,pfuze-support-disable-sw;
+		reg = <0x8>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-name = "V_0V9_GPU";
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-name = "V_0V9_VPU";
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-name = "V_1V1_NVCC_DRAM";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3ab {
+				regulator-name = "V_1V0_DRAM";
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-name = "V_1V8_S0";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-name = "NC";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-name = "V_0V9_SNVS";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-name = "V_0V55_VREF_DDR";
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-name = "V_1V5_CSI";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-name = "V_0V9_PHY";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <975000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-name = "V_1V8_PHY";
+				regulator-min-microvolt = <1675000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-name = "V_1V8_VDDA";
+				regulator-min-microvolt = <1625000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-name = "V_3V3_PHY";
+				regulator-min-microvolt = <3075000>;
+				regulator-max-microvolt = <3625000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-name = "V_2V8_CAM";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	fan-controller@1b {
+		compatible = "maxim,max6650";
+		reg = <0x1b>;
+		maxim,fan-microvolt = <5000000>;
+	};
+
+	rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	sensor@4b {
+		compatible = "national,lm75b";
+		reg = <0x4b>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c32";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	/* TODO: configure audio, as of now just put a placeholder */
+	wm8904: audio-codec@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+		clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
+		clock-names = "mclk";
+		clock-frequency = <24000000>;
+	};
+};
+
+/* M.2 B-key slot */
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	disable-gpio = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
+		 <&clk IMX8MQ_CLK_PCIE1_AUX>,
+		 <&clk IMX8MQ_CLK_PCIE1_PHY>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	ext_osc = <1>;
+	status = "okay";
+};
+
+/* Intel Ethernet Controller I210/I211 */
+&pcie1 {
+	clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+		 <&clk IMX8MQ_CLK_PCIE2_AUX>,
+		 <&clk IMX8MQ_CLK_PCIE2_PHY>,
+		 <&pcie1_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	ext_osc = <1>;
+	fsl,max-link-speed = <1>;
+	status = "okay";
+};
+
+&pgc_gpu {
+	power-supply = <&sw1a_reg>;
+};
+
+&pgc_vpu {
+	power-supply = <&sw1c_reg>;
+};
+
+&qspi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	fsl,uart-has-rtscts;
+	assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
+	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0>;
+	dr_mode = "otg";
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	maximum-speed = "high-speed";
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	resets = <&usb_hub_reset>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vqmmc-supply = <&sw4_reg>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>;
+	assigned-clock-rates = <200000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19 /* TPM Reset */
+			MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4		0x19 /* USB2 Hub Reset */
+		>;
+	};
+
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5			0x19 /* GPIO0 */
+			MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15		0x19 /* GPIO1 */
+			MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17		0x19 /* GPIO2 */
+			MX8MQ_IOMUXC_NAND_WP_B_GPIO3_IO18		0x19 /* GPIO3 */
+			MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16		0x19 /* GPIO4 */
+			MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10		0x19 /* GPIO5 */
+			MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11		0x19 /* GPIO6 */
+			MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12		0x19 /* GPIO7 */
+		>;
+	};
+
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x16 /* PCIE_PERST */
+			MX8MQ_IOMUXC_UART4_TXD_GPIO5_IO29		0x16 /* W_DISABLE */
+		>;
+	};
+
+	pinctrl_reg_usdhc2: regusdhc2gpiogrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x41
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO		0x23
+			MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x16
+			MX8MQ_IOMUXC_GPIO1_IO15_GPIO1_IO15		0x16
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x82
+			MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B		0x82
+			MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0		0x82
+			MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1		0x82
+			MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2		0x82
+			MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3		0x82
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x19
+			MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x19
+			MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x19
+		>;
+	};
+
+	pinctrl_ecspi2_cs: ecspi2csgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x49
+			MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x49
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x49
+			MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x49
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX		0x49
+			MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX		0x49
+			MX8MQ_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B		0x49
+			MX8MQ_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x49
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc3
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3
+			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x83
+			MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x8d
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xcd
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xcd
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xcd
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xcd
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xcd
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xcd
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xcd
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xcd
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xcd
+			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x8d
+			MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x9f
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xdf
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xdf
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xdf
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xdf
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xdf
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xdf
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xdf
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xdf
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xdf
+			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x9f
+			MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12		0x41
+			MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20			0x19
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
+			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
+			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
+			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
+			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
+			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
+			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x8d
+			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcd
+			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xcd
+			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xcd
+			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xcd
+			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xcd
+			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x9f
+			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xdf
+			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xdf
+			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xdf
+			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xdf
+			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xdf
+			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_usb0: usb0grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO12_USB1_OTG_PWR		0x19
+			MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x19
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};