@@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-dora.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-kagura.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-keyaki.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-fxtec-pro1.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb
new file mode 100644
@@ -0,0 +1,185 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8998-mtp.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+ model = "F(x)tec Pro1 (QX1000)";
+ compatible = "fxtec,pro1", "qcom,msm8998";
+ qcom,board-id = <0x02000b 0x10>;
+
+ /*
+ * Until we hook up type-c detection, we
+ * have to stick with this. But it works.
+ */
+ extcon_usb: extcon-usb {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio-hall-sensors {
+ compatible = "gpio-keys";
+ input-name = "hall-sensors";
+ label = "Hall sensors";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hall_sensor1_default>;
+
+ hall-sensor1 {
+ label = "Keyboard Hall Sensor";
+ gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>;
+ debounce-interval = <15>;
+ gpio-key,wakeup;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_KEYPAD_SLIDE>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ input-name = "side-buttons";
+ label = "Side buttons";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_up_pin_a>, <&cam_focus_pin_a>,
+ <&cam_snapshot_pin_a>;
+ vol-up {
+ label = "Volume Up";
+ gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_KEY>;
+ linux,code = <KEY_VOLUMEUP>;
+ gpio-key,wakeup;
+ debounce-interval = <15>;
+ };
+
+ camera-snapshot {
+ label = "Camera Snapshot";
+ gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_KEY>;
+ linux,code = <KEY_CAMERA>;
+ debounce-interval = <15>;
+ };
+
+ camera-focus {
+ label = "Camera Focus";
+ gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_KEY>;
+ linux,code = <KEY_CAMERA_FOCUS>;
+ debounce-interval = <15>;
+ };
+ };
+
+ reserved-memory {
+ cont_splash_mem: memory@9d400000 {
+ reg = <0x0 0x9d400000 0x0 0x2000000>;
+ no-map;
+ };
+
+ zap_shader_region: memory@f6400000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0xf6400000 0x0 0x2000>;
+ no-map;
+ };
+
+ ramoops@ffc00000 {
+ compatible = "ramoops";
+ reg = <0x0 0xffc00000 0x0 0x100000>;
+ console-size = <0x60000>;
+ ecc-size = <16>;
+ ftrace-size = <0x10000>;
+ pmsg-size = <0x20000>;
+ record-size = <0x10000>;
+ };
+ };
+};
+
+&mmcc {
+ status = "ok";
+};
+
+&mmss_smmu {
+ status = "ok";
+};
+
+&pm8998_gpio {
+ vol_up_pin_a: vol-up-active {
+ pins = "gpio6";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+
+ cam_focus_pin_a: cam-focus-btn-active {
+ pins = "gpio7";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+
+ cam_snapshot_pin_a: cam-snapshot-btn-active {
+ pins = "gpio8";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+};
+
+&pm8998_pon {
+ resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ bias-pull-up;
+ debounce = <15625>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>;
+
+ mdp_vsync_n: mdp-vsync-n {
+ pins = "gpio10";
+ function = "mdp_vsync_a";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
+ hall_sensor1_default: hall-sensor1-def {
+ pins = "gpio124";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ input-enable;
+ };
+};
+
+&ufshc {
+ status = "ok";
+};
+
+&ufsphy {
+ status = "ok";
+};
+
+&usb3_dwc3 {
+ dr_mode = "peripheral";
+ extcon = <&extcon_usb>;
+};
+
+/* GT9286 analog supply */
+&vreg_l28_3p0 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
Add device tree support for the F(x)tec Pro 1 (QX1000) smartphone; this is a minimal configuration to boot to serial console. Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8998-fxtec-pro1.dts | 185 ++++++++++++++++++ 2 files changed, 186 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts