[v3,08/10] arm64: dts: qcom: sm8450: add PCIe0 RC device

Add device tree node for the first PCIe host found on the Qualcomm
SM8450 platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 101 +++++++++++++++++++++++++++
 1 file changed, 101 insertions(+)

On 16/12/2021 01:35, Bjorn Andersson wrote:
> On Fri 10 Dec 20:17 CST 2021, Dmitry Baryshkov wrote:
> 
>> Add device tree node for the first PCIe host found on the Qualcomm
>> SM8450 platform.
>>
>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
>> ---
>>   arch/arm64/boot/dts/qcom/sm8450.dtsi | 101 +++++++++++++++++++++++++++
>>   1 file changed, 101 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
>> index a047d8a22897..09087a34a007 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
>> @@ -627,6 +627,84 @@ i2c14: i2c@a98000 {
>>   				#size-cells = <0>;
>>   				status = "disabled";
>>   			};
>> +		];
>> +
>> +		pcie0: pci@1c00000 {
>> +			compatible = "qcom,pcie-sm8450";
>> +			reg = <0 0x01c00000 0 0x3000>,
>> +			      <0 0x60000000 0 0xf1d>,
>> +			      <0 0x60000f20 0 0xa8>,
>> +			      <0 0x60001000 0 0x1000>,
>> +			      <0 0x60100000 0 0x100000>;
>> +			reg-names = "parf", "dbi", "elbi", "atu", "config";
>> +			device_type = "pci";
>> +			linux,pci-domain = <0>;
>> +			bus-range = <0x00 0xff>;
>> +			num-lanes = <1>;
>> +
>> +			#address-cells = <3>;
>> +			#size-cells = <2>;
>> +
>> +			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
>> +				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
>> +
>> +			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "msi";
>> +			#interrupt-cells = <1>;
>> +			interrupt-map-mask = <0 0 0 0x7>;
>> +			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> +					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> +					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> +					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> 
> You need to pad these with a couple more zeros, see 0ac10b291bee
> ("arm64: dts: qcom: Fix 'interrupt-map' parent address cells")

Not quite. sm8450 does not define its (yet), so GICv3 node does not 
define address/size cells.

> 
>> +
>> +			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
>> +				 <&gcc GCC_PCIE_0_PIPE_CLK_SRC>,
>> +				 <&pcie0_lane>,
>> +				 <&rpmhcc RPMH_CXO_CLK>,
>> +				 <&gcc GCC_PCIE_0_AUX_CLK>,
>> +				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
>> +				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
>> +				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
>> +				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
>> +				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
>> +				 <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
>> +				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
>> +			clock-names = "pipe",
>> +				      "pipe_mux",
>> +				      "phy_pipe",
>> +				      "ref",
>> +				      "aux",
>> +				      "cfg",
>> +				      "bus_master",
>> +				      "bus_slave",
>> +				      "slave_q2a",
>> +				      "ddrss_sf_tbu",
>> +				      "aggre0",
>> +				      "aggre1";
>> +
>> +			iommus = <&apps_smmu 0x1c00 0x7f>;
>> +			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
>> +				    <0x100 &apps_smmu 0x1c01 0x1>;
>> +
>> +			resets = <&gcc GCC_PCIE_0_BCR>;
>> +			reset-names = "pci";
>> +
>> +			power-domains = <&gcc PCIE_0_GDSC>;
>> +			power-domain-names = "gdsc";
>> +
>> +			phys = <&pcie0_lane>;
>> +			phy-names = "pciephy";
>> +
>> +			perst-gpio = <&tlmm 94 GPIO_ACTIVE_LOW>;
>> +			enable-gpio = <&tlmm 96 GPIO_ACTIVE_HIGH>;
>> +
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&pcie0_default_state>;
>> +
>> +			interconnects = <&pcie_noc MASTER_PCIE_0 &mc_virt SLAVE_EBI1>;
>> +			interconnect-names = "pci";
>> +
>> +			status = "disabled";
>>   		};
>>   
>>   		pcie0_phy: phy@1c06000 {
>> @@ -763,6 +841,29 @@ tlmm: pinctrl@f100000 {
>>   			gpio-ranges = <&tlmm 0 0 211>;
>>   			wakeup-parent = <&pdc>;
>>   
>> +			pcie0_default_state: pcie0-default {
> 
> Binding states that the node name needs to have the suffix "-state".
> 
> Regards,
> Bjorn
> 
>> +				perst {
>> +					pins = "gpio94";
>> +					function = "gpio";
>> +					drive-strength = <2>;
>> +					bias-pull-down;
>> +				};
>> +
>> +				clkreq {
>> +					pins = "gpio95";
>> +					function = "pcie0_clkreqn";
>> +					drive-strength = <2>;
>> +					bias-pull-up;
>> +				};
>> +
>> +				wake {
>> +					pins = "gpio96";
>> +					function = "gpio";
>> +					drive-strength = <2>;
>> +					bias-pull-up;
>> +				};
>> +			};
>> +
>>   			qup_i2c13_default_state: qup-i2c13-default-state {
>>   				mux {
>>   					pins = "gpio48", "gpio49";
>> -- 
>> 2.33.0
>>