@@ -156,6 +156,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-shift-axolotl.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm850-samsung-w737.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm4250-oneplus-billie2.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm6115p-lenovo-j606f.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm6350-sony-xperia-lena-pdx213.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm6375-sony-xperia-murray-pdx225.dtb
new file mode 100644
@@ -0,0 +1,290 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) 2022 Linaro Limited
+ */
+
+/dts-v1/;
+
+#include "sm6115.dtsi"
+#include "pm6125.dtsi"
+
+/ {
+ model = "Lenovo Tab P11";
+ compatible = "lenovo,j606f", "qcom,sm6115p", "qcom,sm6115";
+ chassis-type = "tablet";
+
+ /* required for bootloader to select correct board */
+ qcom,msm-id = <445 0x10000>, <420 0x10000>;
+ qcom,board-id = <34 3>;
+
+ aliases {
+ mmc0 = &sdhc_2;
+ };
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer0: framebuffer@5c000000 {
+ compatible = "simple-framebuffer";
+ reg = <0 0x5c000000 0 (2000 * 1200 * 4)>;
+ width = <1200>;
+ height = <2000>;
+ stride = <(1200 * 4)>;
+ format = "a8r8g8b8";
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ label = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_up_n>;
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm6125_gpio 5 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ gpio-key,wakeup;
+ };
+ };
+};
+
+&dispcc {
+ /* HACK: disable until a panel driver is ready to retain simplefb */
+ status = "disabled";
+};
+
+&pm6125_gpio {
+ vol_up_n: vol-up-n-state {
+ pins = "gpio5";
+ function = "normal";
+ power-source = <0>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&rpm_requests {
+ regulators-0 {
+ compatible = "qcom,rpm-pm6125-regulators";
+
+ pm6125_s6: s6 {
+ regulator-min-microvolt = <304000>;
+ regulator-max-microvolt = <1456000>;
+ };
+
+ pm6125_s7: s7 {
+ regulator-min-microvolt = <1280000>;
+ regulator-max-microvolt = <2080000>;
+ };
+
+ pm6125_s8: s8 {
+ regulator-min-microvolt = <1064000>;
+ regulator-max-microvolt = <1304000>;
+ };
+
+ pm6125_l1: l1 {
+ regulator-min-microvolt = <952000>;
+ regulator-max-microvolt = <1152000>;
+ };
+
+ pm6125_l4: l4 {
+ regulator-min-microvolt = <488000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ pm6125_l5: l5 {
+ regulator-min-microvolt = <1648000>;
+ /* 3.056V capped to 2.96V for SDHCI */
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ /* Broken hw, this one can't be turned off or SDHCI will break! */
+ regulator-always-on;
+ };
+
+ pm6125_l6: l6 {
+ regulator-min-microvolt = <576000>;
+ regulator-max-microvolt = <656000>;
+ };
+
+ pm6125_l7: l7 {
+ /* 1.2V-1.304V fixed at 1.256V for SDHCI bias */
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1256000>;
+ /*
+ * TODO: SDHCI seems to also work with this one turned off, however
+ * there exists a possibility that it may not work with some very
+ * specific SDCard types, perhaps validating this against a wide
+ * range of models could rule that out, saving some power would
+ * certainly be nice..
+ */
+ regulator-always-on;
+ };
+
+ pm6125_l8: l8 {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <728000>;
+ };
+
+ pm6125_l9: l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ };
+
+ pm6125_l10: l10 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <1904000>;
+ };
+
+ pm6125_l11: l11 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <1952000>;
+ };
+
+ pm6125_l12: l12 {
+ regulator-min-microvolt = <1624000>;
+ regulator-max-microvolt = <1984000>;
+ };
+
+ pm6125_l13: l13 {
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <1952000>;
+ };
+
+ pm6125_l14: l14 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <1904000>;
+ };
+
+ pm6125_l15: l15 {
+ regulator-min-microvolt = <2920000>;
+ regulator-max-microvolt = <3232000>;
+ };
+
+ pm6125_l16: l16 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <1904000>;
+ };
+
+ pm6125_l17: l17 {
+ regulator-min-microvolt = <1152000>;
+ regulator-max-microvolt = <1384000>;
+ };
+
+ pm6125_l18: l18 {
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1312000>;
+ };
+
+ pm6125_l19: l19 {
+ regulator-min-microvolt = <1624000>;
+ regulator-max-microvolt = <3304000>;
+ };
+
+ pm6125_l20: l20 {
+ regulator-min-microvolt = <1624000>;
+ regulator-max-microvolt = <3304000>;
+ };
+
+ pm6125_l21: l21 {
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ pm6125_l22: l22 {
+ regulator-min-microvolt = <2952000>;
+ /* 3.304V capped to 2.96V for SDHCI */
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ /* Broken hw, this one can't be turned off or SDHCI will break! */
+ regulator-always-on;
+ };
+
+ pm6125_l23: l23 {
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3400000>;
+ };
+
+ pm6125_l24: l24 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <3600000>;
+ };
+ };
+};
+
+&sdhc_2 {
+ cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_state_on &sdc2_gate_pin>;
+ pinctrl-1 = <&sdc2_state_off>;
+ vmmc-supply = <&pm6125_l22>;
+ vqmmc-supply = <&pm6125_l5>;
+ no-sdio;
+ no-mmc;
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32764>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <14 4>;
+
+ /*
+ * This is a wholly undocumented pin (other than a single vague "pwr-gpios" reference)
+ * that needs to be toggled for the SD Card slot to work properly..
+ */
+ sdc2_gate_pin: sdc2-gate-state {
+ pins = "gpio45";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ output-high;
+ };
+};
+
+&ufs_mem_hc {
+ vcc-supply = <&pm6125_l24>;
+ vcc-max-microamp = <600000>;
+ vccq2-supply = <&pm6125_l11>;
+ vccq2-max-microamp = <600000>;
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&pm6125_l4>;
+ vdda-pll-supply = <&pm6125_l12>;
+ vddp-ref-clk-supply = <&pm6125_l18>;
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&pm6125_l4>;
+ vdda-pll-supply = <&pm6125_l12>;
+ vdda-phy-dpdm-supply = <&pm6125_l15>;
+ status = "okay";
+};
+
+&xo_board {
+ clock-frequency = <19200000>;
+};
Add an initial device tree for the Lenovo Tab P11. Currently it enables: - simplefb - SD Card slot via SDHCI2 - gpio-keys & PON keys - UFS - RPM regulators - USB2 This has been validated with a rev (62) device. You can check yours next to the serial no. on the sticker in the lower portion of the back side of your tablet. To get a successful boot run: cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/\ sm6115p-lenovo-j606f.dtb > .Image.gz-dtb ~/mkbootimg/mkbootimg.py \ --kernel .Image.gz-dtb \ --ramdisk some/initrd.img \ --pagesize 4096 \ --base 0x0 \ --kernel_offset 0x8000 \ --ramdisk_offset 0x1000000 \ --tags_offset 0x100 \ --cmdline 'SOME_CMDLINE' \ --dtb_offset 0x1f00000 \ --header_version 1 \ --os_version 11 \ --os_patch_level 2022-11 \ -o j606f.img fastboot flash boot j606f.img fastboot flash dtbo empty.img fastboot flash recovery empty.img fastboot reboot Where empty.img is 2 zero-bytes. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/sm6115p-lenovo-j606f.dts | 290 ++++++++++++++++++ 2 files changed, 291 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts