@@ -636,6 +636,133 @@ smd-edge {
label = "lpass";
};
};
+
+ mdss: display-subsystem@fd900000 {
+ compatible = "qcom,mdss";
+ reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
+ reg-names = "mdss_phys", "vbif_phys";
+
+ power-domains = <&mmcc MDSS_GDSC>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "vsync";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ status = "disabled";
+
+ mdp: display-controller@fd900000 {
+ compatible = "qcom,msm8226-mdp5", "qcom,mdp5";
+ reg = <0xfd900100 0x22000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "core",
+ "vsync";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: dsi@fd922800 {
+ compatible = "qcom,msm8226-dsi-ctrl",
+ "qcom,mdss-dsi-ctrl";
+ reg = <0xfd922800 0x1f8>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
+ <&mmcc PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&dsi_phy0 0>,
+ <&dsi_phy0 1>;
+
+ clocks = <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_BYTE0_CLK>,
+ <&mmcc MDSS_PCLK0_CLK>,
+ <&mmcc MDSS_ESC0_CLK>,
+ <&mmcc MMSS_MISC_AHB_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core",
+ "core_mmss";
+
+ phys = <&dsi_phy0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp5_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy0: phy@fd922a00 {
+ compatible = "qcom,dsi-phy-28nm-8226";
+ reg = <0xfd922a00 0xd4>,
+ <0xfd922b00 0x280>,
+ <0xfd922d80 0x30>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface",
+ "ref";
+ };
+ };
};
timer {
Add the nodes that describe the mdss so that display can work on MSM8226. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> --- arch/arm/boot/dts/qcom-msm8226.dtsi | 127 ++++++++++++++++++++++++++++++++++++ 1 file changed, 127 insertions(+)