[v5,4/4] arm64: dts: qcom: Add Acer Aspire 1

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f6ff4024a60e..f0d92c47bc7f 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -78,6 +78,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8540p-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8775p-ride.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-acer-aspire1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts b/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts
new file mode 100644
index 000000000000..d0ec759a44ce
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts
@@ -0,0 +1,854 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc7180.dtsi"
+
+#include "pm6150.dtsi"
+#include "pm6150l.dtsi"
+
+/delete-node/ &tz_mem;
+/delete-node/ &ipa_fw_mem;
+
+/ {
+	model = "Acer Aspire 1";
+	compatible = "acer,aspire1", "qcom,sc7180";
+	chassis-type = "laptop";
+
+	aliases {
+		bluetooth0 = &bluetooth;
+		hsuart0 = &uart3;
+		serial0 = &uart8;
+		wifi0 = &wifi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		zap_mem: zap-shader@80840000 {
+			reg = <0x0 0x80840000 0 0x2000>;
+			no-map;
+		};
+
+		venus_mem: venus@85b00000 {
+			reg = <0x0 0x85b00000 0 0x500000>;
+			no-map;
+		};
+
+		mpss_mem: mpss@86000000 {
+			reg = <0x0 0x86000000 0x0 0x2000000>;
+			no-map;
+		};
+
+		adsp_mem: adsp@8e400000 {
+			reg = <0x0 0x8e400000 0x0 0x2800000>;
+			no-map;
+		};
+
+		wlan_mem: wlan@93900000 {
+			reg = <0x0 0x93900000 0x0 0x200000>;
+			no-map;
+		};
+	};
+
+	max98357a: audio-codec {
+		compatible = "maxim,max98357a";
+		sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&amp_sd_mode_default>;
+		pinctrl-names = "default";
+
+		#sound-dai-cells = <0>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&sn65dsi86_bridge 1000000>;
+		enable-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&soc_bkoff_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_brij_1p2: bridge-1p2-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "brij_1p2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_edp_1p2_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_brij_1p8: bridge-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "brij_1p8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		vin-supply = <&vreg_l8c_1p8>;
+
+		gpio = <&tlmm 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_edp_1p8_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_codec_3p3: codec-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "codec_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_audio_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_lcm_3p3: panel-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "lcm_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		/*
+		 * HACK: Display fails with
+		 *
+		 * *ERROR* Unexpected max rate (0x0); assuming 5.4 GHz
+		 * *ERROR* Link training failed, link is off (-5)
+		 *
+		 * if the power to the panel was ever cut
+		 */
+		regulator-always-on;
+
+		gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_lcm_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_tp_3p3: touchpad-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "tp_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_tp_en_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&dsi0 {
+	vdda-supply = <&vreg_l3c_1p2>;
+	status = "okay";
+};
+
+&dsi0_out {
+	remote-endpoint = <&sn65dsi86_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi_phy {
+	vdds-supply = <&vreg_l4a_0p8>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* embedded-controller@76 */
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/*
+	 * NOTE: DSDT defines two possible touchpads, other one is
+	 *
+	 * reg = <0x15>;
+	 * hid-descr-addr = <0x1>;
+	 */
+
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+		hid-descr-addr = <0x20>;
+
+		vdd-supply = <&reg_tp_3p3>;
+
+		interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&hid_touchpad_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+		hid-descr-addr = <0x1>;
+
+		interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&hid_keyboard_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c9 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	alc5682: codec@1a {
+		compatible = "realtek,rt5682i";
+		reg = <0x1a>;
+
+		#sound-dai-cells = <1>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <28 IRQ_TYPE_EDGE_BOTH>;
+
+		pinctrl-0 = <&codec_irq_default>;
+		pinctrl-names = "default";
+
+		AVDD-supply = <&vreg_l15a_1p8>;
+		MICVDD-supply = <&reg_codec_3p3>;
+		VBAT-supply = <&reg_codec_3p3>;
+
+		realtek,dmic1-data-pin = <1>;
+		realtek,dmic1-clk-pin = <1>;
+		realtek,jd-src = <1>;
+	};
+};
+
+&i2c10 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	sn65dsi86_bridge: bridge@2c {
+		compatible = "ti,sn65dsi86";
+		reg = <0x2c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#pwm-cells = <1>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+		suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&bridge_en_default>,
+			    <&edp_bridge_irq_default>,
+			    <&bridge_suspend_default>;
+		pinctrl-names = "default";
+
+		vpll-supply = <&reg_brij_1p8>;
+		vccio-supply = <&reg_brij_1p8>;
+		vcca-supply = <&reg_brij_1p2>;
+		vcc-supply = <&reg_brij_1p2>;
+
+		clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
+		clock-names = "refclk";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sn65dsi86_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sn65dsi86_out: endpoint {
+					data-lanes = <0 1>;
+					remote-endpoint = <&panel_in_edp>;
+				};
+			};
+		};
+
+		aux-bus {
+			panel: panel {
+				compatible = "edp-panel";
+				power-supply = <&reg_lcm_3p3>;
+				backlight = <&backlight>;
+
+				port {
+					panel_in_edp: endpoint {
+						remote-endpoint = <&sn65dsi86_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		memory-region = <&zap_mem>;
+		firmware-name = "qcom/sc7180/acer/aspire1/qcdxkmsuc7180.mbn";
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&pm6150_adc {
+	thermistor@4e {
+		reg = <ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	charger-thermistor@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm6150_adc_tm {
+	status = "okay";
+
+	charger-thermistor@0 {
+		reg = <0>;
+		io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	thermistor@1 {
+		reg = <1>;
+		io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm6150_pon {
+	status = "disabled";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	firmware-name = "qcom/sc7180/acer/aspire1/qcmpss7180_nm.mbn";
+	status = "okay";
+};
+
+&sdhc_1 {
+	pinctrl-0 = <&sdc1_default>;
+	pinctrl-1 = <&sdc1_sleep>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&vreg_l19a_2p9>;
+	vqmmc-supply = <&vreg_l12a_1p8>;
+
+	status = "okay";
+};
+
+&uart3 {
+	/delete-property/interrupts;
+	interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
+			      <&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
+
+	pinctrl-1 = <&qup_uart3_sleep>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+
+	bluetooth: bluetooth {
+		compatible = "qcom,wcn3991-bt";
+		vddio-supply = <&vreg_l10a_1p8>;
+		vddxo-supply = <&vreg_l1c_1p8>;
+		vddrf-supply = <&vreg_l2c_1p3>;
+		vddch0-supply = <&vreg_l10c_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&uart8 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usb_hub_2_x: hub@1 {
+		compatible = "usbbda,5411";
+		reg = <1>;
+		peer-hub = <&usb_hub_3_x>;
+	};
+
+	usb_hub_3_x: hub@2 {
+		compatible = "usbbda,411";
+		reg = <2>;
+		peer-hub = <&usb_hub_2_x>;
+	};
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l4a_0p8>;
+	vdda-pll-supply = <&vreg_l11a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l17a_3p0>;
+	qcom,imp-res-offset-value = <8>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+	qcom,bias-ctrl-value = <0x22>;
+	qcom,charge-ctrl-value = <3>;
+	qcom,hsdisc-trim-value = <0>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l3c_1p2>;
+	vdda-pll-supply = <&vreg_l4a_0p8>;
+
+	status = "okay";
+};
+
+&venus {
+	firmware-name = "qcom/sc7180/acer/aspire1/qcvss7180.mbn";
+};
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>;
+	vdd-1.8-xo-supply = <&vreg_l1c_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l2c_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l10c_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l11c_3p3>;
+
+	status = "okay";
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm6150-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s1a_1p1: smps1 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+		};
+
+		vreg_l4a_0p8: ldo4 {
+			regulator-min-microvolt = <824000>;
+			regulator-max-microvolt = <928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a_0p6: ldo9 {
+			regulator-min-microvolt = <488000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_1p8: ldo10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		vreg_l11a_1p8: ldo11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_1p8: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2496000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_3p0: ldo17 {
+			regulator-min-microvolt = <2920000>;
+			regulator-max-microvolt = <3232000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a_2p8: ldo18 {
+			regulator-min-microvolt = <2496000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a_2p9: ldo19 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm6150l-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_s8c_1p3: smps8 {
+			regulator-min-microvolt = <1120000>;
+			regulator-max-microvolt = <1408000>;
+		};
+
+		vreg_l1c_1p8: ldo1 {
+			regulator-min-microvolt = <1616000>;
+			regulator-max-microvolt = <1984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_1p3: ldo2 {
+			regulator-min-microvolt = <1168000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_1p2: ldo3 {
+			regulator-min-microvolt = <1144000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c_1p8: ldo4 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5c_1p8: ldo5 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l6c_2p9: ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c_2p9: ldo9 {
+			regulator-min-microvolt = <2952000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10c_3p3: ldo10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11c_3p3: ldo11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+	};
+};
+
+&qup_i2c2_default {
+	drive-strength = <2>;
+
+	/* Has external pullup */
+	bias-disable;
+};
+
+&qup_i2c4_default {
+	drive-strength = <2>;
+
+	/* Has external pullup */
+	bias-disable;
+};
+
+&qup_i2c9_default {
+	drive-strength = <2>;
+
+	/* Has external pullup */
+	bias-disable;
+};
+
+&qup_i2c10_default {
+	drive-strength = <2>;
+
+	/* Has external pullup */
+	bias-disable;
+};
+
+&tlmm {
+	/*
+	 * The TZ seem to protect those because some boards can have
+	 * fingerprint sensor connected to this range. Not connected
+	 * on this board
+	 */
+	gpio-reserved-ranges = <58 5>;
+
+	amp_sd_mode_default: amp-sd-mode-deault-state {
+		pins = "gpio23";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	bridge_en_default: bridge-en-default-state {
+		pins = "gpio51";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	bridge_suspend_default: bridge-suspend-default-state {
+		pins = "gpio22";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+	};
+
+	codec_irq_default: codec-irq-deault-state {
+		pins = "gpio28";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	edp_bridge_irq_default: edp-bridge-irq-default-state {
+		pins = "gpio11";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	hid_keyboard_default: hid-keyboard-default-state {
+		pins = "gpio33";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	hid_touchpad_default: hid-touchpad-default-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	qup_uart3_sleep: qup-uart3-sleep-state {
+		cts-pins {
+			/*
+			 * Configure a pull-down on CTS to match the pull of
+			 * the Bluetooth module.
+			 */
+			pins = "gpio38";
+			function = "gpio";
+			bias-pull-down;
+		};
+
+		rts-pins {
+			/*
+			 * Configure pull-down on RTS. As RTS is active low
+			 * signal, pull it low to indicate the BT SoC that it
+			 * can wakeup the system anytime from suspend state by
+			 * pulling RX low (by sending wakeup bytes).
+			 */
+			pins = "gpio39";
+			function = "gpio";
+			bias-pull-down;
+		};
+
+		tx-pins {
+			/*
+			 * Configure pull-up on TX when it isn't actively driven
+			 * to prevent BT SoC from receiving garbage during sleep.
+			 */
+			pins = "gpio40";
+			function = "gpio";
+			bias-pull-up;
+		};
+
+		rx-pins {
+			/*
+			 * Configure a pull-up on RX. This is needed to avoid
+			 * garbage data when the TX pin of the Bluetooth module
+			 * is floating which may cause spurious wakeups.
+			 */
+			pins = "gpio41";
+			function = "gpio";
+			bias-pull-up;
+		};
+	};
+
+	reg_edp_1p2_en_default: reg-edp-1p2-en-deault-state {
+		pins = "gpio19";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	reg_edp_1p8_en_default: reg-edp-1p8-en-deault-state {
+		pins = "gpio20";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	reg_lcm_en_default: reg-lcm-en-deault-state {
+		pins = "gpio26";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	reg_audio_en_default: reg-audio-en-deault-state {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	reg_tp_en_default: reg-tp-en-deault-state {
+		pins = "gpio25";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	soc_bkoff_default: soc-bkoff-deault-state {
+		pins = "gpio10";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	sdc1_default: sdc1-default-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "sdc1_cmd";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "sdc1_data";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rclk-pins {
+			pins = "sdc1_rclk";
+			bias-pull-down;
+		};
+	};
+
+	sdc1_sleep: sdc1-sleep-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "sdc1_cmd";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "sdc1_data";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		rclk-pins {
+			pins = "sdc1_rclk";
+			bias-pull-down;
+		};
+	};
+};