@@ -99,6 +99,19 @@ config ARM_SCMI_TRANSPORT_OPTEE
If you want the ARM SCMI PROTOCOL stack to include support for a
transport based on OP-TEE SCMI service, answer Y.
+config ARM_SCMI_TRANSPORT_QCOM_HVC
+ bool "SCMI transport based on hvc doorbell & shmem for Qualcomm SoCs"
+ depends on ARCH_QCOM
+ select ARM_SCMI_HAVE_TRANSPORT
+ select ARM_SCMI_HAVE_SHMEM
+ default y
+ help
+ Enable hvc doorbell & shmem based transport for SCMI.
+
+ If you want the ARM SCMI PROTOCOL stack to include support for a
+ hvc doorbell and shmem transport on Qualcomm virtual platforms,
+ answer Y.
+
config ARM_SCMI_TRANSPORT_SMC
bool "SCMI transport based on SMC"
depends on HAVE_ARM_SMCCC_DISCOVERY
@@ -10,6 +10,7 @@ scmi-transport-$(CONFIG_ARM_SCMI_TRANSPORT_SMC) += smc.o
scmi-transport-$(CONFIG_ARM_SCMI_HAVE_MSG) += msg.o
scmi-transport-$(CONFIG_ARM_SCMI_TRANSPORT_VIRTIO) += virtio.o
scmi-transport-$(CONFIG_ARM_SCMI_TRANSPORT_OPTEE) += optee.o
+scmi-transport-$(CONFIG_ARM_SCMI_TRANSPORT_QCOM_HVC) += qcom_hvc.o
scmi-protocols-y = base.o clock.o perf.o power.o reset.o sensors.o system.o voltage.o powercap.o
scmi-module-objs := $(scmi-driver-y) $(scmi-protocols-y) $(scmi-transport-y)
@@ -24,4 +25,5 @@ ifeq ($(CONFIG_THUMB2_KERNEL)$(CONFIG_CC_IS_CLANG),yy)
# pointer in Thumb2 mode, which is forcibly enabled by Clang when profiling
# hooks are inserted via the -pg switch.
CFLAGS_REMOVE_smc.o += $(CC_FLAGS_FTRACE)
+CFLAGS_REMOVE_qcom_hvc.o += $(CC_FLAGS_FTRACE)
endif
@@ -298,6 +298,9 @@ extern const struct scmi_desc scmi_virtio_desc;
#ifdef CONFIG_ARM_SCMI_TRANSPORT_OPTEE
extern const struct scmi_desc scmi_optee_desc;
#endif
+#ifdef CONFIG_ARM_SCMI_TRANSPORT_QCOM_HVC
+extern const struct scmi_desc scmi_qcom_hvc_desc;
+#endif
void scmi_rx_callback(struct scmi_chan_info *cinfo, u32 msg_hdr, void *priv);
@@ -2918,6 +2918,10 @@ static const struct of_device_id scmi_of_match[] = {
#endif
#ifdef CONFIG_ARM_SCMI_TRANSPORT_VIRTIO
{ .compatible = "arm,scmi-virtio", .data = &scmi_virtio_desc},
+#endif
+#ifdef CONFIG_ARM_SCMI_TRANSPORT_QCOM_HVC
+ { .compatible = "qcom,scmi-hvc-shmem",
+ .data = &scmi_qcom_hvc_desc },
#endif
{ /* Sentinel */ },
};
new file mode 100644
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * System Control and Management Interface (SCMI) Message
+ * Qualcomm HVC/shmem Transport driver
+ *
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright 2020 NXP
+ *
+ * This is based on drivers/firmware/arm_scmi/smc.c
+ */
+
+#include <linux/arm-smccc.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/slab.h>
+
+#include "common.h"
+
+/**
+ * struct scmi_qcom_hvc - Structure representing a SCMI qcom hvc transport
+ *
+ * @irq: An optional IRQ for completion
+ * @cinfo: SCMI channel info
+ * @shmem: Transmit/Receive shared memory area
+ * @shmem_lock: Lock to protect access to Tx/Rx shared memory area.
+ * @func_id: hvc call function-id
+ * @cap_id: hvc doorbell's capability id
+ */
+
+struct scmi_qcom_hvc {
+ int irq;
+ struct scmi_chan_info *cinfo;
+ struct scmi_shared_mem __iomem *shmem;
+ /* Protect access to shmem area */
+ struct mutex shmem_lock;
+ u32 func_id;
+ u64 cap_id;
+};
+
+static irqreturn_t qcom_hvc_msg_done_isr(int irq, void *data)
+{
+ struct scmi_qcom_hvc *scmi_info = data;
+
+ scmi_rx_callback(scmi_info->cinfo, shmem_read_header(scmi_info->shmem), NULL);
+
+ return IRQ_HANDLED;
+}
+
+static bool qcom_hvc_chan_available(struct device_node *of_node, int idx)
+{
+ struct device_node *np = of_parse_phandle(of_node, "shmem", 0);
+
+ if (!np)
+ return false;
+
+ of_node_put(np);
+ return true;
+}
+
+static int qcom_hvc_chan_setup(struct scmi_chan_info *cinfo,
+ struct device *dev, bool tx)
+{
+ struct device *cdev = cinfo->dev;
+ struct scmi_qcom_hvc *scmi_info;
+ struct device_node *np;
+ resource_size_t size;
+ struct resource res;
+ u32 func_id;
+ u64 cap_id;
+ int ret;
+
+ if (!tx)
+ return -ENODEV;
+
+ scmi_info = devm_kzalloc(dev, sizeof(*scmi_info), GFP_KERNEL);
+ if (!scmi_info)
+ return -ENOMEM;
+
+ np = of_parse_phandle(cdev->of_node, "shmem", 0);
+ if (!of_device_is_compatible(np, "arm,scmi-shmem")) {
+ of_node_put(np);
+ return -ENXIO;
+ }
+
+ ret = of_address_to_resource(np, 0, &res);
+ of_node_put(np);
+ if (ret) {
+ dev_err(cdev, "failed to get SCMI Tx shared memory\n");
+ return ret;
+ }
+
+ size = resource_size(&res);
+
+ /* The func-id & capability-id are kept in last 16 bytes of shmem.
+ * +-------+
+ * | |
+ * | shmem |
+ * | |
+ * | |
+ * +-------+ <-- (size - 16)
+ * | funcId|
+ * +-------+ <-- (size - 8)
+ * | capId |
+ * +-------+ <-- size
+ */
+
+ scmi_info->shmem = devm_ioremap(dev, res.start, size);
+ if (!scmi_info->shmem) {
+ dev_err(dev, "failed to ioremap SCMI Tx shared memory\n");
+ return -EADDRNOTAVAIL;
+ }
+
+ func_id = readl((void __iomem *)(scmi_info->shmem) + size - 16);
+
+#ifdef CONFIG_ARM64
+ cap_id = readq((void __iomem *)(scmi_info->shmem) + size - 8);
+#else
+ /* capability-id is 32 bit long on 32bit machines */
+ cap_id = readl((void __iomem *)(scmi_info->shmem) + size - 8);
+#endif
+
+ /*
+ * If there is an interrupt named "a2p", then the service and
+ * completion of a message is signaled by an interrupt rather than by
+ * the return of the hvc call.
+ */
+ scmi_info->irq = of_irq_get_byname(cdev->of_node, "a2p");
+ if (scmi_info->irq > 0) {
+ ret = request_irq(scmi_info->irq, qcom_hvc_msg_done_isr,
+ IRQF_NO_SUSPEND, dev_name(dev), scmi_info);
+ if (ret) {
+ dev_err(dev, "failed to setup SCMI completion irq\n");
+ return ret;
+ }
+ } else {
+ cinfo->no_completion_irq = true;
+ }
+
+ scmi_info->func_id = func_id;
+ scmi_info->cap_id = cap_id;
+ scmi_info->cinfo = cinfo;
+ mutex_init(&scmi_info->shmem_lock);
+ cinfo->transport_info = scmi_info;
+
+ return 0;
+}
+
+static int qcom_hvc_chan_free(int id, void *p, void *data)
+{
+ struct scmi_chan_info *cinfo = p;
+ struct scmi_qcom_hvc *scmi_info = cinfo->transport_info;
+
+ /* Ignore any possible further reception on the IRQ path */
+ if (scmi_info->irq > 0)
+ free_irq(scmi_info->irq, scmi_info);
+
+ cinfo->transport_info = NULL;
+ scmi_info->cinfo = NULL;
+
+ return 0;
+}
+
+static int qcom_hvc_send_message(struct scmi_chan_info *cinfo,
+ struct scmi_xfer *xfer)
+{
+ struct scmi_qcom_hvc *scmi_info = cinfo->transport_info;
+ struct arm_smccc_res res;
+
+ /*
+ * Channel will be released only once response has been
+ * surely fully retrieved, so after .mark_txdone()
+ */
+ mutex_lock(&scmi_info->shmem_lock);
+
+ shmem_tx_prepare(scmi_info->shmem, xfer, cinfo);
+
+ arm_smccc_1_1_hvc(scmi_info->func_id, (unsigned long)scmi_info->cap_id,
+ 0, 0, 0, 0, 0, 0, &res);
+
+ if (res.a0) {
+ mutex_unlock(&scmi_info->shmem_lock);
+ return -EOPNOTSUPP;
+ }
+
+ return 0;
+}
+
+static void qcom_hvc_fetch_response(struct scmi_chan_info *cinfo,
+ struct scmi_xfer *xfer)
+{
+ struct scmi_qcom_hvc *scmi_info = cinfo->transport_info;
+
+ shmem_fetch_response(scmi_info->shmem, xfer);
+}
+
+static void qcom_hvc_mark_txdone(struct scmi_chan_info *cinfo, int ret,
+ struct scmi_xfer *__unused)
+{
+ struct scmi_qcom_hvc *scmi_info = cinfo->transport_info;
+
+ mutex_unlock(&scmi_info->shmem_lock);
+}
+
+static bool
+qcom_hvc_poll_done(struct scmi_chan_info *cinfo, struct scmi_xfer *xfer)
+{
+ struct scmi_qcom_hvc *scmi_info = cinfo->transport_info;
+
+ return shmem_poll_done(scmi_info->shmem, xfer);
+}
+
+static const struct scmi_transport_ops scmi_qcom_hvc_ops = {
+ .chan_available = qcom_hvc_chan_available,
+ .chan_setup = qcom_hvc_chan_setup,
+ .chan_free = qcom_hvc_chan_free,
+ .send_message = qcom_hvc_send_message,
+ .mark_txdone = qcom_hvc_mark_txdone,
+ .fetch_response = qcom_hvc_fetch_response,
+ .poll_done = qcom_hvc_poll_done,
+};
+
+const struct scmi_desc scmi_qcom_hvc_desc = {
+ .ops = &scmi_qcom_hvc_ops,
+ .max_rx_timeout_ms = 30,
+ .max_msg = 20,
+ .max_msg_size = 128,
+};
Add a new transport channel to the SCMI firmware interface driver for SCMI message exchange on Qualcomm virtual platforms. The hypervisor associates an object-id also known as capability-id with each hvc doorbell object. The capability-id is used to identify the doorbell from the VM's capability namespace, similar to a file-descriptor. The hypervisor, in addition to the function-id, expects the capability-id to be passed in x1 register when HVC call is invoked. The qcom hvc doorbell/shared memory transport uses a statically defined shared memory region that binds with "arm,scmi-shmem" device tree node. The function-id & capability-id are allocated by the hypervisor on bootup and are stored in the shmem region by the firmware before starting Linux. Currently, there is no usecase for the atomic support therefore this driver doesn't include the changes for the same. Signed-off-by: Nikunj Kela <quic_nkela@quicinc.com> --- drivers/firmware/arm_scmi/Kconfig | 13 ++ drivers/firmware/arm_scmi/Makefile | 2 + drivers/firmware/arm_scmi/common.h | 3 + drivers/firmware/arm_scmi/driver.c | 4 + drivers/firmware/arm_scmi/qcom_hvc.c | 232 +++++++++++++++++++++++++++ 5 files changed, 254 insertions(+) create mode 100644 drivers/firmware/arm_scmi/qcom_hvc.c