mbox series

[v2,0/3] TI TPS6594 PMIC support (RTC, pinctrl, regulators, device trees)

Message ID 20230328091448.648452-1-eblanc@baylibre.com
Headers show
Series TI TPS6594 PMIC support (RTC, pinctrl, regulators, device trees) | expand

Message

Esteban Blanc March 28, 2023, 9:14 a.m. UTC
TPS6594 is a Power Management IC which provides regulators and others
features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and
PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can
communicate through the I2C or SPI interfaces.
TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.

This series adds support to TI TPS6594 PMIC and its derivatives.

This should be applied on top of other patch series:
- https://lore.kernel.org/all/20230216114410.183489-1-jpanis@baylibre.com/
  For core MFD driver

The features implemented in this series are:
- RTC (child device)
- Pinmux/GPIO (child device)
- Regulator (child device)

RTC description:
The TPS6594 family has an RTC built-in, except for LP8764.
It provides time and an alarm.

Pinmux/GPIO:
TPS6594 family has 11 GPIOs. Those GPIO can also serve different
functions such as I2C or SPI interface, watchdog disable functions.
The driver provides both pinmuxing for the functions and GPIO capability.

Regulator:
TPS6594/TPS6593: 5 BUCKs and 4LDOs
LP8764: 4 BUCKs and no LDO
Bucks can be used in multipahse mode

Changes since v1:
Rtc:
- Removed struct tps6594_rtc
- Removed some dev_err messages
- Removed some comments
- Remove some whitespaces in comments and error messages
- Check if RTC is running before reading a timestamp in read_rtc
- Stop RTC at the end of probe to wait for a timestamp to be set
- Add default MFD_TPS6594 to Kconfig

Pinctrl:
- Removed #define DEBUG
- Add default MFD_TPS6594 to Kconfig
- Fix typo and reword help message of Kconfig

Regulators:
Further to Mark Brown review:
- File header whole block C++ style
- Configuring modes not supported: omit all mode operations
- Log the error before notifying
- Request the interrupts while registering the regulators (then remove
  the lookup function)
Further to Matti review:
- Postponed: devm_regulator_irq_helper() and 
  regulator_irq_map_event_simple() can probably be used but code
  refactoring is not so trivial. This can be done later as an enhancement
  after this patch list is merged. 
Buck Multi phase management:
- Multiphase property can take an array when 2 multi phase buck, buck12
  and buck34
- Configuration multi phase buck34 without multiphase buck12 is not
  supported (when only one multiphase, must be buck12). Not clear from the
  spec but confirmed by TI.
- Supported multiphase conficurations: buck12, buck123, buck1234, 
  buck12 + buck34
- All interrupts are attached to the multiphase buck (ie: for regulator
  buck12, buck1 & buck2 interrupts are registered)

Esteban Blanc (2):
  rtc: tps6594: add driver for TPS6594 PMIC RTC
  pinctrl: tps6594: add for TPS6594 PMIC

Jerome Neanne (1):
  regulator: tps6594-regulator: Add driver for TI TPS6594 regulators

 drivers/pinctrl/Kconfig               |  10 +
 drivers/pinctrl/Makefile              |   1 +
 drivers/pinctrl/pinctrl-tps6594.c     | 365 +++++++++++++++
 drivers/regulator/Kconfig             |  13 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/tps6594-regulator.c | 628 ++++++++++++++++++++++++++
 drivers/rtc/Kconfig                   |   9 +
 drivers/rtc/Makefile                  |   1 +
 drivers/rtc/rtc-tps6594.c             | 462 +++++++++++++++++++
 9 files changed, 1490 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-tps6594.c
 create mode 100644 drivers/regulator/tps6594-regulator.c
 create mode 100644 drivers/rtc/rtc-tps6594.c