[v8,00/13] Add support for RaspberryPi RP1 PCI device using a DT overlay

RP1 is an MFD chipset that acts as a south-bridge PCIe endpoint sporting
a pletora of subdevices (i.e.  Ethernet, USB host controller, I2C, PWM,
etc.) whose registers are all reachable starting from an offset from the
BAR address.  The main point here is that while the RP1 as an endpoint
itself is discoverable via usual PCI enumeraiton, the devices it contains
are not discoverable and must be declared e.g. via the devicetree.

This patchset is an attempt to provide a minimum infrastructure to allow
the RP1 chipset to be discovered and perpherals it contains to be added
from a devictree overlay loaded during RP1 PCI endpoint enumeration. To
ensure compatibility with downstream, a devicetree already comprising the
RP1 node is also provided, so it's not strictly necessary to use the
dynamically loaded overlay if the devicetree is already fully defined at
the origin.
To achieve this modularity, the RP1 node DT definitions are arranged by
file inclusion as per following schema (the arrow points to the includer,
see also [9]):
 
 rp1-pci.dtso         rp1.dtso
     ^                    ^
     |                    |
rp1-common.dtsi ----> rp1-nexus.dtsi ----> bcm2712-rpi-5-b-monolithic.dts
                                               ^
                                               |
                                           bcm2712-rpi-5-b.dts

Followup patches should add support for the several peripherals contained
in RP1.

This work is based upon dowstream drivers code and the proposal from RH
et al. (see [1] and [2]). A similar approach is also pursued in [3].

The patches are ordered as follows:

-PATCHES 1 to 4: add binding schemas for clock, gpio and RP1 peripherals.
 They are needed to support the other peripherals, e.g. the ethernet mac
 depends on a clock generated by RP1 and the phy is reset through the
 on-board gpio controller.

-PATCH 5 and 6: add clock and gpio device drivers.

-PATCH 7: the devicetree node describing the RP1 chipset. Please
 note that this patch should be taken by the same maintainer that will
 also take patch 8, since the definition it contains is possibly used
 by the dtso compiled in as binary blob and is closely coupled to the
 driver.

-PATCH 8: this is the main patch to support RP1 chipset. It can work
 either with a fully defined devicetree (i.e. one that already included
 the rp1 node since boot time) or with a runtime loaded dtb overlay
 which is linked as binary blob in the driver obj. This duality is
 useful to comply with both downstream and upstream needs (see [9]).
 The real dtso is in devicetree folder while the dtso in driver folder is
 just a placeholder to include the real dtso.
 In this way it is possible to check the dtso against dt-bindings.
 The reason why drivers/misc has been selected as containing folder
 for this driver can be seen in [6], [7] and [8].

-PATCH 9: the fully fledged devictree containing also the rp1 node.
 This devicetree is similar to the one downstream is using.

-PATCH 10 (OPTIONAL): this patch introduces a new scenario about how
 the rp1 node is specified and loaded in DT. On top of the base DT
 (without rp1 node), the fw loads this overlay and the end result is
 the same devicetree as in patch 9, which is then passed to the next
 stage (either the kernel or u-boot/bootloader).
 While this patch is not strictly necessary and can therefore be dropped
 (see [10]), it's not introducing much extra work and maybe can come
 in handy while debugging.
 
-PATCH 11: add the external clock node (used by RP1) to the main dts.

-PATCH 12: add the relevant kernel CONFIG_ options to defconfig.

-PATCH 13: enable CONFIG_OF_OVERLAY in order for 'make defconfig'
 to produce a configuration valid for the RP1 driver. Without this
 patch, the user has to explicitly enable it since the misc driver
 depends on OF_OVERLAY.

This patchset is also a first attempt to be more agnostic wrt hardware
description standards such as OF devicetree and ACPI, where 'agnostic'
means "using DT in coexistence with ACPI", as been already promoted
by e.g. AL (see [4]). Although there's currently no evidence it will also
run out of the box on purely ACPI system, it is a first step towards
that direction.

Many thanks,
Andrea della Porta

Links:
- [1]: https://lpc.events/event/17/contributions/1421/attachments/1337/2680/LPC2023%20Non-discoverable%20devices%20in%20PCI.pdf
- [2]: https://lore.kernel.org/lkml/20230419231155.GA899497-robh@kernel.org/t/
- [3]: https://lore.kernel.org/all/20240808154658.247873-1-herve.codina@bootlin.com/#t
- [4]: https://lore.kernel.org/all/73e05c77-6d53-4aae-95ac-415456ff0ae4@lunn.ch/
- [5]: https://lore.kernel.org/all/20240626104544.14233-1-svarbanov@suse.de/
- [6]: https://lore.kernel.org/all/20240612140208.GC1504919@google.com/
- [7]: https://lore.kernel.org/all/83f7fa09-d0e6-4f36-a27d-cee08979be2a@app.fastmail.com/
- [8]: https://lore.kernel.org/all/2024081356-mutable-everyday-6f9d@gregkh/
- [9]: https://lore.kernel.org/all/Z87wTfChRC5Ruwc0@apocalypse/
- [10]: https://lore.kernel.org/all/CAMEGJJ0f4YUgdWBhxvQ_dquZHztve9KO7pvQjoDWJ3=zd3cgcg@mail.gmail.com/#t

CHANGES IN V8


PATCH RELATED -------------------------------------------------

- This cover letter and patch 8 commit messages now have
  more details explaining the new DT include files organization.

- Added two new patches numbered 9 and 10 respectively dealing
  with the new DT inclusion schema.


BINDINGS ------------------------------------------------------

- Modified maintainer first name for get_maintainer.pl to be able
  to retrieve the entire name correctly from the .yaml files. As
  a consequence, MAINTAINERS file does not need an entry for
  schemas anymore.

- pci1de4,1.yaml: Added a statement about the ints activation
  type for rp1 peripherals: only level high or rising edge
  are supported since they all are active high only.

RP1 PINCTRL DRIVER ---------------------------------

- Added GPIOCHIP_IRQ_RESOURCE_HELPERS.


RP1 CLOCK DRIVER ------------------------------------

- Added PLL_DIV_INVALID to denote invalid values in pll_sec_div_table[].

- Dropped some empty lines.

- Changed TODO comment to better reflect the intent

- Changed a WARN() into WARN_ONCE() to prevent flooding

- Fixed the hard limit condition "rate > 4000000000ll" in
  rp1_clock_set_rate_and_parent() to "rate > data->max_freq", in order
  to check against the limit specific for that clock.

- Style change: dropped an empty line


RP1 MISC DRIVER -----------------------------------

- rp1_pci.c: Added a suitable dev_err() warning in case
  of_platform_default_populate() fails.

- rp1_pci.c: Fixed the mismatching %d vs %u in dev_dbg().

- rp1_pci.c: Changed the error string printed on pci_alloc_irq_vectors()
  failure, plus minor cosmetic changes such as capitalization of error
  strings. 

- rp1_pci.c: Changed dev_err() to dev_err_probe() where appropriate.

- rp1_pci.c: Updated the year in the top header copyright notice,
  also added a newline between lines. Also, changed the error string
  'Not initialised' to 'Not initialized'.

- rp1_pci.c: Changed MODULE_DESCRIPTION() string to match the one
  in Kconfig.

- rp1-pci.dtso: Minor change to the top header comment to unify
  the multi-line comment style.

- Kconfig: Changed description in the header comment to match the
  description in the tristate option.


Andrea della Porta (13):
  dt-bindings: clock: Add RaspberryPi RP1 clock bindings
  dt-bindings: pinctrl: Add RaspberryPi RP1 gpio/pinctrl/pinmux bindings
  dt-bindings: pci: Add common schema for devices accessible through PCI
    BARs
  dt-bindings: misc: Add device specific bindings for RaspberryPi RP1
  clk: rp1: Add support for clocks provided by RP1
  pinctrl: rp1: Implement RaspberryPi RP1 gpio support
  arm64: dts: rp1: Add support for RaspberryPi's RP1 device
  misc: rp1: RaspberryPi RP1 misc driver
  arm64: dts: Add board DTS for Rpi5 which includes RP1 node
  arm64: dts: Add overlay for RP1 device
  arm64: dts: bcm2712: Add external clock for RP1 chipset on Rpi5
  arm64: defconfig: Enable RP1 misc/clock/gpio drivers
  arm64: defconfig: Enable OF_OVERLAY option

 .../clock/raspberrypi,rp1-clocks.yaml         |   58 +
 .../devicetree/bindings/misc/pci1de4,1.yaml   |  137 ++
 .../devicetree/bindings/pci/pci-ep-bus.yaml   |   58 +
 .../pinctrl/raspberrypi,rp1-gpio.yaml         |  198 +++
 MAINTAINERS                                   |    8 +
 arch/arm64/boot/dts/broadcom/Makefile         |    4 +-
 .../broadcom/bcm2712-rpi-5-b-monolithic.dts   |    8 +
 .../boot/dts/broadcom/bcm2712-rpi-5-b.dts     |    7 +
 arch/arm64/boot/dts/broadcom/rp1-common.dtsi  |   42 +
 arch/arm64/boot/dts/broadcom/rp1-nexus.dtsi   |   14 +
 arch/arm64/boot/dts/broadcom/rp1.dtso         |   11 +
 arch/arm64/configs/defconfig                  |    4 +
 drivers/clk/Kconfig                           |    9 +
 drivers/clk/Makefile                          |    1 +
 drivers/clk/clk-rp1.c                         | 1512 +++++++++++++++++
 drivers/misc/Kconfig                          |    1 +
 drivers/misc/Makefile                         |    1 +
 drivers/misc/rp1/Kconfig                      |   20 +
 drivers/misc/rp1/Makefile                     |    3 +
 drivers/misc/rp1/rp1-pci.dtso                 |   25 +
 drivers/misc/rp1/rp1_pci.c                    |  333 ++++
 drivers/pci/quirks.c                          |    1 +
 drivers/pinctrl/Kconfig                       |   11 +
 drivers/pinctrl/Makefile                      |    1 +
 drivers/pinctrl/pinctrl-rp1.c                 |  790 +++++++++
 .../clock/raspberrypi,rp1-clocks.h            |   61 +
 include/linux/pci_ids.h                       |    3 +
 27 files changed, 3320 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/clock/raspberrypi,rp1-clocks.yaml
 create mode 100644 Documentation/devicetree/bindings/misc/pci1de4,1.yaml
 create mode 100644 Documentation/devicetree/bindings/pci/pci-ep-bus.yaml
 create mode 100644 Documentation/devicetree/bindings/pinctrl/raspberrypi,rp1-gpio.yaml
 create mode 100644 arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b-monolithic.dts
 create mode 100644 arch/arm64/boot/dts/broadcom/rp1-common.dtsi
 create mode 100644 arch/arm64/boot/dts/broadcom/rp1-nexus.dtsi
 create mode 100644 arch/arm64/boot/dts/broadcom/rp1.dtso
 create mode 100644 drivers/clk/clk-rp1.c
 create mode 100644 drivers/misc/rp1/Kconfig
 create mode 100644 drivers/misc/rp1/Makefile
 create mode 100644 drivers/misc/rp1/rp1-pci.dtso
 create mode 100644 drivers/misc/rp1/rp1_pci.c
 create mode 100644 drivers/pinctrl/pinctrl-rp1.c
 create mode 100644 include/dt-bindings/clock/raspberrypi,rp1-clocks.h

Hello,

> Common YAML schema for devices that exports internal peripherals through
> PCI BARs. The BARs are exposed as simple-buses through which the
> peripherals can be accessed.
> 
> This is not intended to be used as a standalone binding, but should be
> included by device specific bindings.

Applied to dt-bindings, thank you!

	Krzysztof