diff mbox series

[net-next,v4,8/8] net: txgbe: Support phylink MAC layer

Message ID 20230422045621.360918-9-jiawenwu@trustnetic.com
State Superseded
Headers show
Series TXGBE PHYLINK support | expand

Commit Message

Jiawen Wu April 22, 2023, 4:56 a.m. UTC
Add phylink support to Wangxun 10Gb Ethernet controller for the 10GBASE-R
interface.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |  1 +
 .../ethernet/wangxun/txgbe/txgbe_ethtool.c    | 28 ++++++
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   | 23 ++---
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 91 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  5 +
 5 files changed, 135 insertions(+), 13 deletions(-)

Comments

Simon Horman April 23, 2023, 7:57 p.m. UTC | #1
On Sat, Apr 22, 2023 at 12:56:21PM +0800, Jiawen Wu wrote:
> Add phylink support to Wangxun 10Gb Ethernet controller for the 10GBASE-R
> interface.
> 
> Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

...

> +static int txgbe_phylink_init(struct txgbe *txgbe)
> +{
> +	struct phylink_config *config;
> +	struct fwnode_handle *fwnode;
> +	struct wx *wx = txgbe->wx;
> +	phy_interface_t phy_mode;
> +	struct phylink *phylink;
> +
> +	config = devm_kzalloc(&wx->pdev->dev, sizeof(*config), GFP_KERNEL);
> +	if (!config)
> +		return -ENOMEM;
> +
> +	config->dev = &wx->netdev->dev;
> +	config->type = PHYLINK_NETDEV;
> +	config->mac_capabilities = MAC_10000FD | MAC_1000FD | MAC_SYM_PAUSE | MAC_ASYM_PAUSE;
> +	phy_mode = PHY_INTERFACE_MODE_10GBASER;
> +	__set_bit(PHY_INTERFACE_MODE_10GBASER, config->supported_interfaces);
> +	fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_PHYLINK]);
> +	phylink = phylink_create(config, fwnode, phy_mode, &txgbe_mac_ops);
> +	if (IS_ERR(phylink))
> +		return PTR_ERR(phylink);
> +
> +	txgbe->phylink = phylink;
> +
> +	return 0;
> +}

Hi Jiawen,

txgbe_phylink_init() seems unused.
Perhaps it needs to be wired-up somewhere?
Jiawen Wu April 24, 2023, 1:49 a.m. UTC | #2
On Monday, April 24, 2023 3:58 AM, Simon Horman wrote:
> On Sat, Apr 22, 2023 at 12:56:21PM +0800, Jiawen Wu wrote:
> > Add phylink support to Wangxun 10Gb Ethernet controller for the 10GBASE-R
> > interface.
> >
> > Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
> 
> ...
> 
> > +static int txgbe_phylink_init(struct txgbe *txgbe)
> > +{
> > +	struct phylink_config *config;
> > +	struct fwnode_handle *fwnode;
> > +	struct wx *wx = txgbe->wx;
> > +	phy_interface_t phy_mode;
> > +	struct phylink *phylink;
> > +
> > +	config = devm_kzalloc(&wx->pdev->dev, sizeof(*config), GFP_KERNEL);
> > +	if (!config)
> > +		return -ENOMEM;
> > +
> > +	config->dev = &wx->netdev->dev;
> > +	config->type = PHYLINK_NETDEV;
> > +	config->mac_capabilities = MAC_10000FD | MAC_1000FD | MAC_SYM_PAUSE | MAC_ASYM_PAUSE;
> > +	phy_mode = PHY_INTERFACE_MODE_10GBASER;
> > +	__set_bit(PHY_INTERFACE_MODE_10GBASER, config->supported_interfaces);
> > +	fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_PHYLINK]);
> > +	phylink = phylink_create(config, fwnode, phy_mode, &txgbe_mac_ops);
> > +	if (IS_ERR(phylink))
> > +		return PTR_ERR(phylink);
> > +
> > +	txgbe->phylink = phylink;
> > +
> > +	return 0;
> > +}
> 
> Hi Jiawen,
> 
> txgbe_phylink_init() seems unused.
> Perhaps it needs to be wired-up somewhere?
> 

Oops, I forgot to add it to txgbe_init_phy().
diff mbox series

Patch

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index dde979b623fa..e303bff0b13a 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -43,6 +43,7 @@  config TXGBE
 	select I2C_DESIGNWARE_PLATFORM
 	select GPIOLIB_IRQCHIP
 	select GPIOLIB
+	select PHYLINK
 	select PCS_XPCS
 	select LIBWX
 	select SFP
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
index d914e9a05404..859da112586a 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
@@ -6,11 +6,39 @@ 
 #include <linux/netdevice.h>
 
 #include "../libwx/wx_ethtool.h"
+#include "../libwx/wx_type.h"
+#include "txgbe_type.h"
 #include "txgbe_ethtool.h"
 
+static int txgbe_nway_reset(struct net_device *netdev)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_nway_reset(txgbe->phylink);
+}
+
+static int txgbe_get_link_ksettings(struct net_device *netdev,
+				    struct ethtool_link_ksettings *cmd)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_ksettings_get(txgbe->phylink, cmd);
+}
+
+static int txgbe_set_link_ksettings(struct net_device *netdev,
+				    const struct ethtool_link_ksettings *cmd)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_ksettings_set(txgbe->phylink, cmd);
+}
+
 static const struct ethtool_ops txgbe_ethtool_ops = {
 	.get_drvinfo		= wx_get_drvinfo,
+	.nway_reset		= txgbe_nway_reset,
 	.get_link		= ethtool_op_get_link,
+	.get_link_ksettings	= txgbe_get_link_ksettings,
+	.set_link_ksettings	= txgbe_set_link_ksettings,
 };
 
 void txgbe_set_ethtool_ops(struct net_device *netdev)
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
index b1ede19f4ff8..04091355a5d8 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
@@ -7,6 +7,7 @@ 
 #include <linux/netdevice.h>
 #include <linux/string.h>
 #include <linux/etherdevice.h>
+#include <linux/phylink.h>
 #include <net/ip.h>
 #include <linux/if_vlan.h>
 
@@ -204,7 +205,8 @@  static int txgbe_request_irq(struct wx *wx)
 
 static void txgbe_up_complete(struct wx *wx)
 {
-	u32 reg;
+	struct net_device *netdev = wx->netdev;
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
 
 	wx_control_hw(wx, true);
 	wx_configure_vectors(wx);
@@ -213,24 +215,16 @@  static void txgbe_up_complete(struct wx *wx)
 	smp_mb__before_atomic();
 	wx_napi_enable_all(wx);
 
+	phylink_start(txgbe->phylink);
+
 	/* clear any pending interrupts, may auto mask */
 	rd32(wx, WX_PX_IC(0));
 	rd32(wx, WX_PX_IC(1));
 	rd32(wx, WX_PX_MISC_IC);
 	txgbe_irq_enable(wx, true);
 
-	/* Configure MAC Rx and Tx when link is up */
-	reg = rd32(wx, WX_MAC_RX_CFG);
-	wr32(wx, WX_MAC_RX_CFG, reg);
-	wr32(wx, WX_MAC_PKT_FLT, WX_MAC_PKT_FLT_PR);
-	reg = rd32(wx, WX_MAC_WDG_TIMEOUT);
-	wr32(wx, WX_MAC_WDG_TIMEOUT, reg);
-	reg = rd32(wx, WX_MAC_TX_CFG);
-	wr32(wx, WX_MAC_TX_CFG, (reg & ~WX_MAC_TX_CFG_SPEED_MASK) | WX_MAC_TX_CFG_SPEED_10G);
-
 	/* enable transmits */
-	netif_tx_start_all_queues(wx->netdev);
-	netif_carrier_on(wx->netdev);
+	netif_tx_start_all_queues(netdev);
 }
 
 static void txgbe_reset(struct wx *wx)
@@ -264,7 +258,6 @@  static void txgbe_disable_device(struct wx *wx)
 		wx_disable_rx_queue(wx, wx->rx_ring[i]);
 
 	netif_tx_stop_all_queues(netdev);
-	netif_carrier_off(netdev);
 	netif_tx_disable(netdev);
 
 	wx_irq_disable(wx);
@@ -295,8 +288,12 @@  static void txgbe_disable_device(struct wx *wx)
 
 static void txgbe_down(struct wx *wx)
 {
+	struct net_device *netdev = wx->netdev;
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
 	txgbe_disable_device(wx);
 	txgbe_reset(wx);
+	phylink_stop(txgbe->phylink);
 
 	wx_clean_all_tx_rings(wx);
 	wx_clean_all_rx_rings(wx);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 3e5be9aa3b04..937ee9a703ec 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -8,11 +8,13 @@ 
 #include <linux/gpio/driver.h>
 #include <linux/gpio/property.h>
 #include <linux/pcs/pcs-xpcs.h>
+#include <linux/phylink.h>
 #include <linux/mdio.h>
 #include <linux/i2c.h>
 #include <linux/pci.h>
 
 #include "../libwx/wx_type.h"
+#include "../libwx/wx_lib.h"
 #include "../libwx/wx_hw.h"
 #include "txgbe_type.h"
 #include "txgbe_phy.h"
@@ -153,6 +155,95 @@  static int txgbe_mdio_pcs_init(struct txgbe *txgbe)
 	return 0;
 }
 
+static struct phylink_pcs *txgbe_phylink_mac_select(struct phylink_config *config,
+						    phy_interface_t interface)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(to_net_dev(config->dev));
+
+	return &txgbe->xpcs->pcs;
+}
+
+static void txgbe_mac_config(struct phylink_config *config, unsigned int mode,
+			     const struct phylink_link_state *state)
+{
+}
+
+static void txgbe_mac_link_down(struct phylink_config *config,
+				unsigned int mode, phy_interface_t interface)
+{
+	struct wx *wx = netdev_priv(to_net_dev(config->dev));
+
+	wr32m(wx, WX_MAC_TX_CFG, WX_MAC_TX_CFG_TE, 0);
+}
+
+static void txgbe_mac_link_up(struct phylink_config *config,
+			      struct phy_device *phy,
+			      unsigned int mode, phy_interface_t interface,
+			      int speed, int duplex,
+			      bool tx_pause, bool rx_pause)
+{
+	struct wx *wx = netdev_priv(to_net_dev(config->dev));
+	u32 txcfg, wdg;
+
+	txcfg = rd32(wx, WX_MAC_TX_CFG);
+	txcfg &= ~WX_MAC_TX_CFG_SPEED_MASK;
+
+	switch (speed) {
+	case SPEED_10000:
+		txcfg |= WX_MAC_TX_CFG_SPEED_10G;
+		break;
+	case SPEED_1000:
+	case SPEED_100:
+	case SPEED_10:
+		txcfg |= WX_MAC_TX_CFG_SPEED_1G;
+		break;
+	default:
+		break;
+	}
+
+	wr32(wx, WX_MAC_TX_CFG, txcfg | WX_MAC_TX_CFG_TE);
+
+	/* Re configure MAC Rx */
+	wr32m(wx, WX_MAC_RX_CFG, WX_MAC_RX_CFG_RE, WX_MAC_RX_CFG_RE);
+	wr32(wx, WX_MAC_PKT_FLT, WX_MAC_PKT_FLT_PR);
+	wdg = rd32(wx, WX_MAC_WDG_TIMEOUT);
+	wr32(wx, WX_MAC_WDG_TIMEOUT, wdg);
+}
+
+static const struct phylink_mac_ops txgbe_mac_ops = {
+	.mac_select_pcs = txgbe_phylink_mac_select,
+	.mac_config = txgbe_mac_config,
+	.mac_link_down = txgbe_mac_link_down,
+	.mac_link_up = txgbe_mac_link_up,
+};
+
+static int txgbe_phylink_init(struct txgbe *txgbe)
+{
+	struct phylink_config *config;
+	struct fwnode_handle *fwnode;
+	struct wx *wx = txgbe->wx;
+	phy_interface_t phy_mode;
+	struct phylink *phylink;
+
+	config = devm_kzalloc(&wx->pdev->dev, sizeof(*config), GFP_KERNEL);
+	if (!config)
+		return -ENOMEM;
+
+	config->dev = &wx->netdev->dev;
+	config->type = PHYLINK_NETDEV;
+	config->mac_capabilities = MAC_10000FD | MAC_1000FD | MAC_SYM_PAUSE | MAC_ASYM_PAUSE;
+	phy_mode = PHY_INTERFACE_MODE_10GBASER;
+	__set_bit(PHY_INTERFACE_MODE_10GBASER, config->supported_interfaces);
+	fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_PHYLINK]);
+	phylink = phylink_create(config, fwnode, phy_mode, &txgbe_mac_ops);
+	if (IS_ERR(phylink))
+		return PTR_ERR(phylink);
+
+	txgbe->phylink = phylink;
+
+	return 0;
+}
+
 static int txgbe_gpio_get(struct gpio_chip *chip, unsigned int offset)
 {
 	struct wx *wx = gpiochip_get_data(chip);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 89a635593ae2..95ed19912a34 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -80,6 +80,10 @@ 
 				TXGBE_PX_MISC_INT_ERR | \
 				TXGBE_PX_MISC_GPIO)
 
+/* Port cfg registers */
+#define TXGBE_CFG_PORT_ST                       0x14404
+#define TXGBE_CFG_PORT_ST_LINK_UP               BIT(0)
+
 /* I2C registers */
 #define TXGBE_I2C_BASE                          0x14900
 
@@ -180,6 +184,7 @@  struct txgbe {
 	struct txgbe_nodes nodes;
 	struct mdio_device *mdiodev;
 	struct dw_xpcs *xpcs;
+	struct phylink *phylink;
 	struct platform_device *sfp_dev;
 	struct platform_device *i2c_dev;
 	struct gpio_chip *gpio;