diff mbox series

[33/37] arm64: dts: renesas: rzg3l-smarc-som: add initial support for RZ/G3S SMARC Carrier-II SoM

Message ID 20230912045157.177966-34-claudiu.beznea.uj@bp.renesas.com
State New
Headers show
Series Add new Renesas RZ/G3S SoC and RZ/G3S SMARC EVK | expand

Commit Message

Claudiu Sept. 12, 2023, 4:51 a.m. UTC
From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>

Add initial support for RZ/G3S SMARC Carrier-II SoM. SoM contains the following
devices:
- RZ/G3S microcontroller: Renesas R9A08G045S33GBG
- 9-channel PMIC: Renesas RAA215300
- Clock Generator: Renesas 5L35023B
- 128M QSPI Flash: Renesas AT25QL128A
- 8G LPDDR4 SDRAM: Micron MT53D512M16D1DS-046
- 64GB eMMC Flash: Micron MTFC64GBCAQTC
- 2x Gigabit Ethernet Transceiver: Microchip KSZ9131RNX
- 5x Current Monitors: Renesas ISL28025FR12Z

The following interfaces are available on SoM board:
- 2 uSD interfaces
- 12-pin, 1.0mm pitch connector to the RZ/G3S ADC IO
- 4-pin, 1.0mm pitch connector to the RZ/G3S I3C IO
- JTAG connector

At the moment the 24MHz output of 5L35023B, memory SD ch0 (with all its
bits) were described in device tree.

SD channel 0 of RZ/G3S is connected to an uSD card interface
and an eMMC. The selection b/w them is done though a hardware switch.
The DT will select b/w uSD and eMMC though SW_SD0_DEV_SEL build flag.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
---
 .../boot/dts/renesas/rzg3s-smarc-som.dtsi     | 147 ++++++++++++++++++
 1 file changed, 147 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi

Comments

Geert Uytterhoeven Sept. 15, 2023, 2:28 p.m. UTC | #1
Hi Claudiu,

Thanks for your patch!

On Tue, Sep 12, 2023 at 6:53 AM Claudiu <claudiu.beznea@tuxon.dev> wrote:
> From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
>
> Add initial support for RZ/G3S SMARC Carrier-II SoM. SoM contains the following
> devices:
> - RZ/G3S microcontroller: Renesas R9A08G045S33GBG
> - 9-channel PMIC: Renesas RAA215300
> - Clock Generator: Renesas 5L35023B
> - 128M QSPI Flash: Renesas AT25QL128A
> - 8G LPDDR4 SDRAM: Micron MT53D512M16D1DS-046

That's an 8 Gib part, so 1 GiB?

> - 64GB eMMC Flash: Micron MTFC64GBCAQTC
> - 2x Gigabit Ethernet Transceiver: Microchip KSZ9131RNX
> - 5x Current Monitors: Renesas ISL28025FR12Z
>
> The following interfaces are available on SoM board:
> - 2 uSD interfaces
> - 12-pin, 1.0mm pitch connector to the RZ/G3S ADC IO
> - 4-pin, 1.0mm pitch connector to the RZ/G3S I3C IO
> - JTAG connector

Please drop the description of parts you are not adding to the DTS yet.

> At the moment the 24MHz output of 5L35023B, memory SD ch0 (with all its
> bits) were described in device tree.
>
> SD channel 0 of RZ/G3S is connected to an uSD card interface
> and an eMMC. The selection b/w them is done though a hardware switch.
> The DT will select b/w uSD and eMMC though SW_SD0_DEV_SEL build flag.
>
> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>

> --- /dev/null
> +++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
> @@ -0,0 +1,147 @@
> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +/*
> + * Device Tree Source for the R9A08G045S33 SMARC Carrier-II's SoM board.
> + *
> + * Copyright (C) 2023 Renesas Electronics Corp.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
> +
> +/*
> + * Signals of SW_CONFIG switches:
> + * @SW_SD0_DEV_SEL:
> + *     0 - SD0 is connected to eMMC
> + *     1 - SD0 is connected to uSD0 card
> + */
> +#define SW_SD0_DEV_SEL 1
> +
> +/ {
> +       aliases {
> +               mmc0 = &sdhi0;
> +       };
> +
> +       chosen {
> +               bootargs = "ignore_loglevel";
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       memory@48000000 {
> +               device-type = "memory";
> +               /* First 128MB is reserved for secure area. */
> +               reg = <0x0 0x48000000 0x0 0x38000000>;
> +       };
> +
> +       reg_3p3v: regulator0 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "fixed-3.3V";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +#if SW_SD0_DEV_SEL
> +       vccq_sdhi0: regulator1 {
> +               compatible = "regulator-gpio";
> +               regulator-name = "SDHI0 VccQ";
> +               regulator-min-microvolt = <1800000>;
> +               regulator-max-microvolt = <3300000>;
> +               gpios = <&pinctrl RZG2L_GPIO(2, 2) GPIO_ACTIVE_HIGH>;
> +               gpios-states = <1>;
> +               states = <3300000 1>, <1800000 0>;
> +       };
> +#else
> +       reg_1p8v: regulator1 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "fixed-1.8V";
> +               regulator-min-microvolt = <1800000>;
> +               regulator-max-microvolt = <1800000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +#endif
> +};
> +
> +&extal_clk {
> +       clock-frequency = <24000000>;
> +};
> +
> +#if SW_SD0_DEV_SEL
> +/* SD0 slot */
> +&sdhi0 {
> +       pinctrl-0 = <&sdhi0_pins>;
> +       pinctrl-1 = <&sdhi0_uhs_pins>;
> +       pinctrl-names = "default", "state_uhs";
> +       vmmc-supply = <&reg_3p3v>;
> +       vqmmc-supply = <&vccq_sdhi0>;
> +       bus-width = <4>;
> +       sd-uhs-sdr50;
> +       sd-uhs-sdr104;
> +       max-frequency = <125000000>;
> +       status = "okay";
> +};
> +#else
> +/* eMMC */
> +&sdhi0 {
> +       pinctrl-0 = <&sdhi0_emmc_pins>;
> +       pinctrl-1 = <&sdhi0_emmc_pins>;
> +       pinctrl-names = "default", "state_uhs";
> +       vmmc-supply = <&reg_3p3v>;
> +       vqmmc-supply = <&reg_1p8v>;
> +       bus-width = <8>;
> +       mmc-hs200-1_8v;
> +       non-removable;
> +       fixed-emmc-driver-type = <1>;
> +       max-frequency = <125000000>;
> +       status = "okay";
> +};
> +#endif
> +
> +&pinctrl {
> +       sd0-pwr-en-hog {
> +               gpio-hog;
> +               gpios = <RZG2L_GPIO(2, 1) GPIO_ACTIVE_HIGH>;

According to the schematics, P2_1 controls power to the uSD slot.
Hence shouldn't reg_3p3v above be modelled using regulator-gpio,
with enable-gpios pointing to P2_1?

> +               output-high;
> +               line-name = "sd0_pwr_en";
> +       };
Gr{oetje,eeting}s,

                        Geert
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
new file mode 100644
index 000000000000..ea53b9ff7b6f
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
@@ -0,0 +1,147 @@ 
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the R9A08G045S33 SMARC Carrier-II's SoM board.
+ *
+ * Copyright (C) 2023 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/*
+ * Signals of SW_CONFIG switches:
+ * @SW_SD0_DEV_SEL:
+ *	0 - SD0 is connected to eMMC
+ *	1 - SD0 is connected to uSD0 card
+ */
+#define SW_SD0_DEV_SEL	1
+
+/ {
+	aliases {
+		mmc0 = &sdhi0;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@48000000 {
+		device-type = "memory";
+		/* First 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	reg_3p3v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+#if SW_SD0_DEV_SEL
+	vccq_sdhi0: regulator1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&pinctrl RZG2L_GPIO(2, 2) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
+	};
+#else
+	reg_1p8v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+#endif
+};
+
+&extal_clk {
+	clock-frequency = <24000000>;
+};
+
+#if SW_SD0_DEV_SEL
+/* SD0 slot */
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_uhs_pins>;
+	pinctrl-names = "default", "state_uhs";
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	max-frequency = <125000000>;
+	status = "okay";
+};
+#else
+/* eMMC */
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_emmc_pins>;
+	pinctrl-1 = <&sdhi0_emmc_pins>;
+	pinctrl-names = "default", "state_uhs";
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	fixed-emmc-driver-type = <1>;
+	max-frequency = <125000000>;
+	status = "okay";
+};
+#endif
+
+&pinctrl {
+	sd0-pwr-en-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(2, 1) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "sd0_pwr_en";
+	};
+
+	sdhi0_pins: sd0 {
+		data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <3300>;
+		};
+
+		ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <3300>;
+		};
+
+		cd {
+			pinmux = <RZG2L_PORT_PINMUX(0, 0, 1)>; /* SD0_CD */
+		};
+	};
+
+	sdhi0_uhs_pins: sd0-uhs {
+		data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <1800>;
+		};
+
+		ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		cd {
+			pinmux = <RZG2L_PORT_PINMUX(0, 0, 1)>; /* SD0_CD */
+		};
+	};
+
+	sdhi0_emmc_pins: sd0-emmc {
+		pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+		       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7",
+		       "SD0_CLK", "SD0_CMD", "SD0_RST#";
+		power-source = <1800>;
+	};
+};