@@ -503,6 +503,7 @@ M: Kim Seer Paller <kimseer.paller@analog.com>
S: Supported
W: https://ez.analog.com/linux-software-drivers
F: Documentation/devicetree/bindings/gpio/gpio-adg1414.yaml
+F: drivers/gpio/gpio-adg1414.c
ADM1025 HARDWARE MONITOR DRIVER
M: Jean Delvare <jdelvare@suse.com>
@@ -1797,6 +1797,16 @@ config GPIO_74X164
shift registers. This driver can be used to provide access
to more GPIO outputs.
+config GPIO_ADG1414
+ tristate "ADG1414 Serially-Controlled Octal SPST Switches"
+ depends on SPI
+ help
+ Say yes here to build support for Analog Devices ADG1414
+ Serially-Controlled Octal SPST Switches
+
+ To compile this driver as a module, choose M here: the
+ module will be called gpio-adg1414.
+
config GPIO_MAX3191X
tristate "Maxim MAX3191x industrial serializer"
select CRC8
@@ -24,6 +24,7 @@ obj-$(CONFIG_GPIO_104_IDI_48) += gpio-104-idi-48.o
obj-$(CONFIG_GPIO_104_IDIO_16) += gpio-104-idio-16.o
obj-$(CONFIG_GPIO_74X164) += gpio-74x164.o
obj-$(CONFIG_GPIO_74XX_MMIO) += gpio-74xx-mmio.o
+obj-$(CONFIG_GPIO_ADG1414) += gpio-adg1414.o
obj-$(CONFIG_GPIO_ADNP) += gpio-adnp.o
obj-$(CONFIG_GPIO_ADP5520) += gpio-adp5520.o
obj-$(CONFIG_GPIO_ADP5585) += gpio-adp5585.o
new file mode 100644
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ADG1414 Serially-Controlled Octal SPST Switches
+ *
+ * Copyright 2025 Analog Devices Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+#define ADG1414_MAX_DEVICES 4
+
+struct adg1414_state {
+ struct spi_device *spi;
+ struct gpio_chip chip;
+ struct regmap *regmap;
+ struct mutex lock; /* protect sensor state */
+ u32 buf;
+
+ __be32 tx __aligned(ARCH_DMA_MINALIGN);
+};
+
+static int adg1414_spi_write(void *context, const void *data, size_t count)
+{
+ struct adg1414_state *st = context;
+
+ struct spi_transfer xfer = {
+ .tx_buf = &st->tx,
+ .len = count,
+ };
+
+ return spi_sync_transfer(st->spi, &xfer, 1);
+}
+
+static int adg1414_spi_read(void *context, const void *reg, size_t reg_size,
+ void *val, size_t val_size)
+{
+ return 0;
+}
+
+static int adg1414_get(struct gpio_chip *chip, unsigned int offset)
+{
+ struct adg1414_state *st = gpiochip_get_data(chip);
+
+ guard(mutex)(&st->lock);
+
+ return st->buf & BIT(offset);
+}
+
+static void adg1414_set(struct gpio_chip *chip, unsigned int offset, int value)
+{
+ struct adg1414_state *st = gpiochip_get_data(chip);
+
+ guard(mutex)(&st->lock);
+
+ if (value)
+ st->buf |= BIT(offset);
+ else
+ st->buf &= ~BIT(offset);
+
+ st->tx = cpu_to_be32(st->buf << (32 - st->chip.ngpio));
+
+ adg1414_spi_write(st, 0, st->chip.ngpio / 8);
+}
+
+static const struct regmap_bus adg1414_regmap_bus = {
+ .write = adg1414_spi_write,
+ .read = adg1414_spi_read,
+ .reg_format_endian_default = REGMAP_ENDIAN_BIG,
+ .val_format_endian_default = REGMAP_ENDIAN_BIG,
+};
+
+static const struct regmap_config adg1414_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+};
+
+static int adg1414_get_direction(struct gpio_chip *chip,
+ unsigned int offset)
+{
+ return GPIO_LINE_DIRECTION_OUT;
+}
+
+static int adg1414_probe(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct adg1414_state *st;
+ struct gpio_desc *reset;
+ u32 num_devices;
+ int ret;
+
+ st = devm_kzalloc(dev, sizeof(*st), GFP_KERNEL);
+ if (!st)
+ return -ENOMEM;
+
+ st->spi = spi;
+
+ st->regmap = devm_regmap_init(dev, &adg1414_regmap_bus, st,
+ &adg1414_regmap_config);
+ if (IS_ERR(st->regmap))
+ return dev_err_probe(dev, PTR_ERR(st->regmap),
+ "Failed to initialize regmap");
+
+ /* Use reset pin to reset the device */
+ reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(reset))
+ return dev_err_probe(dev, PTR_ERR(reset),
+ "Failed to get reset gpio");
+
+ if (reset) {
+ fsleep(1);
+ gpiod_set_value_cansleep(reset, 0);
+ }
+
+ num_devices = 1;
+ ret = device_property_read_u32(dev, "#daisy-chained-devices",
+ &num_devices);
+ if (!ret) {
+ if (!num_devices || num_devices > ADG1414_MAX_DEVICES)
+ return dev_err_probe(dev, ret,
+ "Failed to get daisy-chained-devices property\n");
+ }
+
+ st->chip.label = "adg1414";
+ st->chip.parent = dev;
+ st->chip.get_direction = adg1414_get_direction;
+ st->chip.set = adg1414_set;
+ st->chip.get = adg1414_get;
+ st->chip.base = -1;
+ st->chip.ngpio = num_devices * 8;
+ st->chip.can_sleep = true;
+
+ ret = devm_mutex_init(dev, &st->lock);
+ if (ret)
+ return ret;
+
+ return devm_gpiochip_add_data(dev, &st->chip, st);
+}
+
+static const struct of_device_id adg1414_of_match[] = {
+ { .compatible = "adi,adg1414-gpio" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, adg1414_of_match);
+
+static struct spi_driver adg1414_driver = {
+ .driver = {
+ .name = "adg1414-gpio",
+ .of_match_table = adg1414_of_match,
+ },
+ .probe = adg1414_probe,
+};
+module_spi_driver(adg1414_driver);
+
+MODULE_AUTHOR("Kim Seer Paller <kimseer.paller@analog.com>");
+MODULE_DESCRIPTION("ADG1414 Serially-Controlled Octal SPST Switches");
+MODULE_LICENSE("GPL");
The ADG1414 is a 9.5 Ω RON ±15 V/+12 V/±5 V iCMOS Serially-Controlled Octal SPST Switches Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com> --- MAINTAINERS | 1 + drivers/gpio/Kconfig | 10 +++ drivers/gpio/Makefile | 1 + drivers/gpio/gpio-adg1414.c | 162 ++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 174 insertions(+)