diff mbox series

[v3,2/3] gpio: pcie-idio-24: Migrate to the regmap API

Message ID 278e328cd1689a4e331e7515050c12c29f2a4785.1678034378.git.william.gray@linaro.org
State Superseded
Headers show
Series Migrate the PCIe-IDIO-24 and WS16C48 GPIO drivers to the regmap API | expand

Commit Message

William Breathitt Gray March 5, 2023, 5:01 p.m. UTC
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.

For the PCIe-IDIO-24 series of devices, the following BARs are
available:

    BAR[0]: memory mapped PEX8311
    BAR[1]: I/O mapped PEX8311
    BAR[2]: I/O mapped card registers

There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS
lines (which may be configured for either output or input). The GPIO
lines are exposed by the following card registers:

    Base +0x0-0x2 (Read/Write): FET Outputs
    Base +0xB (Read/Write): TTL/CMOS
    Base +0x4-0x6 (Read): Isolated Inputs
    Base +0x7 (Read): TTL/CMOS

In order for the device to support interrupts, the PLX PEX8311 internal
PCI wire interrupt and local interrupt input must first be enabled.

The following card registers for Change-Of-State may be used:

    Base +0x8-0xA (Read): COS Status Inputs
    Base +0x8-0xA (Write): COS Clear Inputs
    Base +0xB (Read): COS Status TTL/CMOS
    Base +0xB (Write): COS Clear TTL/CMOS
    Base +0xE (Read/Write): COS Enable

The COS Enable register is used to enable/disable interrupts and
configure the interrupt levels; each bit maps to a group of eight inputs
as described below:

    Bit 0: IRQ EN Rising Edge IN0-7
    Bit 1: IRQ EN Rising Edge IN8-15
    Bit 2: IRQ EN Rising Edge IN16-23
    Bit 3: IRQ EN Rising Edge TTL0-7
    Bit 4: IRQ EN Falling Edge IN0-7
    Bit 5: IRQ EN Falling Edge IN8-15
    Bit 6: IRQ EN Falling Edge IN16-23
    Bit 7: IRQ EN Falling Edge TTL0-7

An interrupt is asserted when a change-of-state matching the interrupt
level configuration respective for a particular group of eight inputs
with enabled COS is detected.

The COS Status registers may be read to determine which inputs have
changed; if interrupts were enabled, an IRQ will be generated for the
set bits in these registers. Writing the value read from the COS Status
register back to the respective COS Clear register will clear just those
interrupts.

Cc: Arnaud de Turckheim <quarium@gmail.com>
Cc: John Hentges <jhentges@accesio.com>
Cc: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
---
Changes in v3:
 - Adjust ws16c48_set_type_config() for parameter list
 - Add mutex to prevent clobbering the COS_ENABLE register when masking
   IRQ and setting their type configuration
Changes in v2:
 - Simplify PCIe-IDIO-24 register offset defines to remove superfluous
   arithmetic
 - Check for NULL pointer after chip->irq_drv_data allocation
 - Set gpio_regmap drvdata and use gpio_regmap_get_drvdata() to get the
   regmap in idio_24_reg_map_xlate()

 drivers/gpio/Kconfig             |   3 +
 drivers/gpio/gpio-pcie-idio-24.c | 709 ++++++++++++-------------------
 2 files changed, 285 insertions(+), 427 deletions(-)

Comments

kernel test robot March 5, 2023, 8:03 p.m. UTC | #1
Hi William,

I love your patch! Perhaps something to improve:

[auto build test WARNING on 4827aae061337251bb91801b316157a78b845ec7]

url:    https://github.com/intel-lab-lkp/linux/commits/William-Breathitt-Gray/regmap-Pass-irq_drv_data-as-a-parameter-for-set_type_config/20230306-010313
base:   4827aae061337251bb91801b316157a78b845ec7
patch link:    https://lore.kernel.org/r/278e328cd1689a4e331e7515050c12c29f2a4785.1678034378.git.william.gray%40linaro.org
patch subject: [PATCH v3 2/3] gpio: pcie-idio-24: Migrate to the regmap API
config: i386-randconfig-a013 (https://download.01.org/0day-ci/archive/20230306/202303060355.RtbgFd25-lkp@intel.com/config)
compiler: clang version 14.0.6 (https://github.com/llvm/llvm-project f28c006a5895fc0e329fe15fead81e37457cb1d1)
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # https://github.com/intel-lab-lkp/linux/commit/e60d5c32ff098c33b1e171190079ed3f40180008
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review William-Breathitt-Gray/regmap-Pass-irq_drv_data-as-a-parameter-for-set_type_config/20230306-010313
        git checkout e60d5c32ff098c33b1e171190079ed3f40180008
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=i386 olddefconfig
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=i386 SHELL=/bin/bash drivers/gpio/

If you fix the issue, kindly add following tag where applicable
| Reported-by: kernel test robot <lkp@intel.com>
| Link: https://lore.kernel.org/oe-kbuild-all/202303060355.RtbgFd25-lkp@intel.com/

All warnings (new ones prefixed by >>):

>> drivers/gpio/gpio-pcie-idio-24.c:365:2: warning: variable 'idio24gpio' is uninitialized when used here [-Wuninitialized]
           idio24gpio->map = devm_regmap_init_mmio(dev, idio_24_regs,
           ^~~~~~~~~~
   drivers/gpio/gpio-pcie-idio-24.c:333:33: note: initialize the variable 'idio24gpio' to silence this warning
           struct idio_24_gpio *idio24gpio;
                                          ^
                                           = NULL
   1 warning generated.


vim +/idio24gpio +365 drivers/gpio/gpio-pcie-idio-24.c

   329	
   330	static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
   331	{
   332		struct device *const dev = &pdev->dev;
   333		struct idio_24_gpio *idio24gpio;
   334		int err;
   335		const size_t pci_plx_bar_index = 1;
   336		const size_t pci_bar_index = 2;
   337		const char *const name = pci_name(pdev);
   338		struct gpio_regmap_config gpio_config = {};
   339		void __iomem *pex8311_intcsr;
   340		void __iomem *idio_24_regs;
   341		struct regmap *pex8311_intcsr_map;
   342		struct regmap_irq_chip *chip;
   343		struct regmap_irq_chip_data *chip_data;
   344	
   345		err = pcim_enable_device(pdev);
   346		if (err) {
   347			dev_err(dev, "Failed to enable PCI device (%d)\n", err);
   348			return err;
   349		}
   350	
   351		err = pcim_iomap_regions(pdev, BIT(pci_plx_bar_index) | BIT(pci_bar_index), name);
   352		if (err) {
   353			dev_err(dev, "Unable to map PCI I/O addresses (%d)\n", err);
   354			return err;
   355		}
   356	
   357		pex8311_intcsr = pcim_iomap_table(pdev)[pci_plx_bar_index] + PLX_PEX8311_PCI_LCS_INTCSR;
   358		idio_24_regs = pcim_iomap_table(pdev)[pci_bar_index];
   359	
   360		pex8311_intcsr_map = devm_regmap_init_mmio(dev, pex8311_intcsr,
   361							   &pex8311_intcsr_regmap_config);
   362		if (IS_ERR(pex8311_intcsr_map))
   363			return dev_err_probe(dev, PTR_ERR(pex8311_intcsr_map),
   364					     "Unable to initialize PEX8311 register map\n");
 > 365		idio24gpio->map = devm_regmap_init_mmio(dev, idio_24_regs,
   366						    &idio_24_regmap_config);
   367		if (IS_ERR(idio24gpio->map))
   368			return dev_err_probe(dev, PTR_ERR(idio24gpio->map),
   369					     "Unable to initialize register map\n");
   370	
   371		idio24gpio = devm_kzalloc(dev, sizeof(*idio24gpio), GFP_KERNEL);
   372		if (!idio24gpio)
   373			return -ENOMEM;
   374	
   375		mutex_init(&idio24gpio->lock);
   376	
   377		/* Initialize all IRQ type configuration to IRQ_TYPE_EDGE_BOTH */
   378		idio24gpio->irq_type = GENMASK(7, 0);
   379	
   380		chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
   381		if (!chip)
   382			return -ENOMEM;
   383	
   384		chip->name = name;
   385		chip->status_base = IDIO_24_COS_STATUS_BASE;
   386		chip->mask_base = IDIO_24_COS_ENABLE;
   387		chip->ack_base = IDIO_24_COS_STATUS_BASE;
   388		chip->num_regs = 4;
   389		chip->irqs = idio_24_regmap_irqs;
   390		chip->num_irqs = ARRAY_SIZE(idio_24_regmap_irqs);
   391		chip->handle_mask_sync = idio_24_handle_mask_sync;
   392		chip->set_type_config = idio_24_set_type_config;
   393		chip->irq_drv_data = idio24gpio;
   394	
   395		/* Software board reset */
   396		err = regmap_write(idio24gpio->map, IDIO_24_SOFT_RESET, 0);
   397		if (err)
   398			return err;
   399		/*
   400		 * enable PLX PEX8311 internal PCI wire interrupt and local interrupt
   401		 * input
   402		 */
   403		err = regmap_update_bits(pex8311_intcsr_map, 0x0, IDIO_24_ENABLE_IRQ,
   404					 IDIO_24_ENABLE_IRQ);
   405		if (err)
   406			return err;
   407	
   408		err = devm_regmap_add_irq_chip(dev, idio24gpio->map, pdev->irq, 0, 0,
   409					       chip, &chip_data);
   410		if (err)
   411			return dev_err_probe(dev, err, "IRQ registration failed\n");
   412	
   413		gpio_config.parent = dev;
   414		gpio_config.regmap = idio24gpio->map;
   415		gpio_config.ngpio = IDIO_24_NGPIO;
   416		gpio_config.names = idio_24_names;
   417		gpio_config.reg_dat_base = GPIO_REGMAP_ADDR(IDIO_24_OUT_BASE);
   418		gpio_config.reg_set_base = GPIO_REGMAP_ADDR(IDIO_24_OUT_BASE);
   419		gpio_config.reg_dir_out_base = GPIO_REGMAP_ADDR(IDIO_24_CONTROL_REG);
   420		gpio_config.ngpio_per_reg = IDIO_24_NGPIO_PER_REG;
   421		gpio_config.irq_domain = regmap_irq_get_domain(chip_data);
   422		gpio_config.reg_mask_xlate = idio_24_reg_mask_xlate;
   423		gpio_config.drvdata = idio24gpio->map;
   424	
   425		return PTR_ERR_OR_ZERO(devm_gpio_regmap_register(dev, &gpio_config));
   426	}
   427
kernel test robot March 6, 2023, 8:31 a.m. UTC | #2
Hi William,

url:    https://github.com/intel-lab-lkp/linux/commits/William-Breathitt-Gray/regmap-Pass-irq_drv_data-as-a-parameter-for-set_type_config/20230306-010313
base:   4827aae061337251bb91801b316157a78b845ec7
patch link:    https://lore.kernel.org/r/278e328cd1689a4e331e7515050c12c29f2a4785.1678034378.git.william.gray%40linaro.org
patch subject: [PATCH v3 2/3] gpio: pcie-idio-24: Migrate to the regmap API
config: loongarch-randconfig-m041-20230305 (https://download.01.org/0day-ci/archive/20230306/202303060606.ooBzB3pr-lkp@intel.com/config)
compiler: loongarch64-linux-gcc (GCC) 12.1.0

If you fix the issue, kindly add following tag where applicable
| Reported-by: kernel test robot <lkp@intel.com>
| Reported-by: Dan Carpenter <error27@gmail.com>
| Link: https://lore.kernel.org/r/202303060606.ooBzB3pr-lkp@intel.com/

smatch warnings:
drivers/gpio/gpio-pcie-idio-24.c:365 idio_24_probe() error: potentially dereferencing uninitialized 'idio24gpio'.

vim +/idio24gpio +365 drivers/gpio/gpio-pcie-idio-24.c

58556204662812 William Breathitt Gray 2018-01-09  330  static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
58556204662812 William Breathitt Gray 2018-01-09  331  {
58556204662812 William Breathitt Gray 2018-01-09  332  	struct device *const dev = &pdev->dev;
58556204662812 William Breathitt Gray 2018-01-09  333  	struct idio_24_gpio *idio24gpio;
58556204662812 William Breathitt Gray 2018-01-09  334  	int err;
10a2f11d3c9e48 Arnaud de Turckheim    2020-11-04  335  	const size_t pci_plx_bar_index = 1;
58556204662812 William Breathitt Gray 2018-01-09  336  	const size_t pci_bar_index = 2;
58556204662812 William Breathitt Gray 2018-01-09  337  	const char *const name = pci_name(pdev);
e60d5c32ff098c William Breathitt Gray 2023-03-05  338  	struct gpio_regmap_config gpio_config = {};
e60d5c32ff098c William Breathitt Gray 2023-03-05  339  	void __iomem *pex8311_intcsr;
e60d5c32ff098c William Breathitt Gray 2023-03-05  340  	void __iomem *idio_24_regs;
e60d5c32ff098c William Breathitt Gray 2023-03-05  341  	struct regmap *pex8311_intcsr_map;
e60d5c32ff098c William Breathitt Gray 2023-03-05  342  	struct regmap_irq_chip *chip;
e60d5c32ff098c William Breathitt Gray 2023-03-05  343  	struct regmap_irq_chip_data *chip_data;
58556204662812 William Breathitt Gray 2018-01-09  344  
58556204662812 William Breathitt Gray 2018-01-09  345  	err = pcim_enable_device(pdev);
58556204662812 William Breathitt Gray 2018-01-09  346  	if (err) {
58556204662812 William Breathitt Gray 2018-01-09  347  		dev_err(dev, "Failed to enable PCI device (%d)\n", err);
58556204662812 William Breathitt Gray 2018-01-09  348  		return err;
58556204662812 William Breathitt Gray 2018-01-09  349  	}
58556204662812 William Breathitt Gray 2018-01-09  350  
10a2f11d3c9e48 Arnaud de Turckheim    2020-11-04  351  	err = pcim_iomap_regions(pdev, BIT(pci_plx_bar_index) | BIT(pci_bar_index), name);
58556204662812 William Breathitt Gray 2018-01-09  352  	if (err) {
58556204662812 William Breathitt Gray 2018-01-09  353  		dev_err(dev, "Unable to map PCI I/O addresses (%d)\n", err);
58556204662812 William Breathitt Gray 2018-01-09  354  		return err;
58556204662812 William Breathitt Gray 2018-01-09  355  	}
58556204662812 William Breathitt Gray 2018-01-09  356  
e60d5c32ff098c William Breathitt Gray 2023-03-05  357  	pex8311_intcsr = pcim_iomap_table(pdev)[pci_plx_bar_index] + PLX_PEX8311_PCI_LCS_INTCSR;
e60d5c32ff098c William Breathitt Gray 2023-03-05  358  	idio_24_regs = pcim_iomap_table(pdev)[pci_bar_index];
e60d5c32ff098c William Breathitt Gray 2023-03-05  359  
e60d5c32ff098c William Breathitt Gray 2023-03-05  360  	pex8311_intcsr_map = devm_regmap_init_mmio(dev, pex8311_intcsr,
e60d5c32ff098c William Breathitt Gray 2023-03-05  361  						   &pex8311_intcsr_regmap_config);
e60d5c32ff098c William Breathitt Gray 2023-03-05  362  	if (IS_ERR(pex8311_intcsr_map))
e60d5c32ff098c William Breathitt Gray 2023-03-05  363  		return dev_err_probe(dev, PTR_ERR(pex8311_intcsr_map),
e60d5c32ff098c William Breathitt Gray 2023-03-05  364  				     "Unable to initialize PEX8311 register map\n");
e60d5c32ff098c William Breathitt Gray 2023-03-05 @365  	idio24gpio->map = devm_regmap_init_mmio(dev, idio_24_regs,
e60d5c32ff098c William Breathitt Gray 2023-03-05  366  					    &idio_24_regmap_config);

Heh.  This needs to be after the idio24gpio = devm_kzalloc().

e60d5c32ff098c William Breathitt Gray 2023-03-05  367  	if (IS_ERR(idio24gpio->map))
e60d5c32ff098c William Breathitt Gray 2023-03-05  368  		return dev_err_probe(dev, PTR_ERR(idio24gpio->map),
e60d5c32ff098c William Breathitt Gray 2023-03-05  369  				     "Unable to initialize register map\n");
e60d5c32ff098c William Breathitt Gray 2023-03-05  370  
e60d5c32ff098c William Breathitt Gray 2023-03-05  371  	idio24gpio = devm_kzalloc(dev, sizeof(*idio24gpio), GFP_KERNEL);
e60d5c32ff098c William Breathitt Gray 2023-03-05  372  	if (!idio24gpio)
e60d5c32ff098c William Breathitt Gray 2023-03-05  373  		return -ENOMEM;
e60d5c32ff098c William Breathitt Gray 2023-03-05  374  
e60d5c32ff098c William Breathitt Gray 2023-03-05  375  	mutex_init(&idio24gpio->lock);
e60d5c32ff098c William Breathitt Gray 2023-03-05  376  
e60d5c32ff098c William Breathitt Gray 2023-03-05  377  	/* Initialize all IRQ type configuration to IRQ_TYPE_EDGE_BOTH */
e60d5c32ff098c William Breathitt Gray 2023-03-05  378  	idio24gpio->irq_type = GENMASK(7, 0);
e60d5c32ff098c William Breathitt Gray 2023-03-05  379  
e60d5c32ff098c William Breathitt Gray 2023-03-05  380  	chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
e60d5c32ff098c William Breathitt Gray 2023-03-05  381  	if (!chip)
e60d5c32ff098c William Breathitt Gray 2023-03-05  382  		return -ENOMEM;
e60d5c32ff098c William Breathitt Gray 2023-03-05  383  
e60d5c32ff098c William Breathitt Gray 2023-03-05  384  	chip->name = name;
diff mbox series

Patch

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 406e8bda487f..06c7a96e6033 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -1578,7 +1578,10 @@  config GPIO_PCI_IDIO_16
 
 config GPIO_PCIE_IDIO_24
 	tristate "ACCES PCIe-IDIO-24 GPIO support"
+	select REGMAP_IRQ
+	select REGMAP_MMIO
 	select GPIOLIB_IRQCHIP
+	select GPIO_REGMAP
 	help
 	  Enables GPIO support for the ACCES PCIe-IDIO-24 family (PCIe-IDIO-24,
 	  PCIe-IDI-24, PCIe-IDO-24, PCIe-IDIO-12). An interrupt is generated
diff --git a/drivers/gpio/gpio-pcie-idio-24.c b/drivers/gpio/gpio-pcie-idio-24.c
index 8a9b98fa418f..41c409998cd9 100644
--- a/drivers/gpio/gpio-pcie-idio-24.c
+++ b/drivers/gpio/gpio-pcie-idio-24.c
@@ -15,17 +15,16 @@ 
  * This driver supports the following ACCES devices: PCIe-IDIO-24,
  * PCIe-IDI-24, PCIe-IDO-24, and PCIe-IDIO-12.
  */
-#include <linux/bitmap.h>
-#include <linux/bitops.h>
+#include <linux/bits.h>
 #include <linux/device.h>
-#include <linux/errno.h>
-#include <linux/gpio/driver.h>
-#include <linux/interrupt.h>
-#include <linux/irqdesc.h>
+#include <linux/err.h>
+#include <linux/gpio/regmap.h>
+#include <linux/irq.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/mutex.h>
 #include <linux/pci.h>
-#include <linux/spinlock.h>
+#include <linux/regmap.h>
 #include <linux/types.h>
 
 /*
@@ -68,416 +67,253 @@ 
 #define PLX_PEX8311_PCI_LCS_INTCSR  0x68
 #define INTCSR_INTERNAL_PCI_WIRE    BIT(8)
 #define INTCSR_LOCAL_INPUT          BIT(11)
+#define IDIO_24_ENABLE_IRQ          (INTCSR_INTERNAL_PCI_WIRE | INTCSR_LOCAL_INPUT)
 
-/**
- * struct idio_24_gpio_reg - GPIO device registers structure
- * @out0_7:	Read: FET Outputs 0-7
- *		Write: FET Outputs 0-7
- * @out8_15:	Read: FET Outputs 8-15
- *		Write: FET Outputs 8-15
- * @out16_23:	Read: FET Outputs 16-23
- *		Write: FET Outputs 16-23
- * @ttl_out0_7:	Read: TTL/CMOS Outputs 0-7
- *		Write: TTL/CMOS Outputs 0-7
- * @in0_7:	Read: Isolated Inputs 0-7
- *		Write: Reserved
- * @in8_15:	Read: Isolated Inputs 8-15
- *		Write: Reserved
- * @in16_23:	Read: Isolated Inputs 16-23
- *		Write: Reserved
- * @ttl_in0_7:	Read: TTL/CMOS Inputs 0-7
- *		Write: Reserved
- * @cos0_7:	Read: COS Status Inputs 0-7
- *		Write: COS Clear Inputs 0-7
- * @cos8_15:	Read: COS Status Inputs 8-15
- *		Write: COS Clear Inputs 8-15
- * @cos16_23:	Read: COS Status Inputs 16-23
- *		Write: COS Clear Inputs 16-23
- * @cos_ttl0_7:	Read: COS Status TTL/CMOS 0-7
- *		Write: COS Clear TTL/CMOS 0-7
- * @ctl:	Read: Control Register
- *		Write: Control Register
- * @reserved:	Read: Reserved
- *		Write: Reserved
- * @cos_enable:	Read: COS Enable
- *		Write: COS Enable
- * @soft_reset:	Read: IRQ Output Pin Status
- *		Write: Software Board Reset
- */
-struct idio_24_gpio_reg {
-	u8 out0_7;
-	u8 out8_15;
-	u8 out16_23;
-	u8 ttl_out0_7;
-	u8 in0_7;
-	u8 in8_15;
-	u8 in16_23;
-	u8 ttl_in0_7;
-	u8 cos0_7;
-	u8 cos8_15;
-	u8 cos16_23;
-	u8 cos_ttl0_7;
-	u8 ctl;
-	u8 reserved;
-	u8 cos_enable;
-	u8 soft_reset;
-};
+#define IDIO_24_OUT_BASE 0x0
+#define IDIO_24_TTLCMOS_OUT_REG 0x3
+#define IDIO_24_IN_BASE 0x4
+#define IDIO_24_TTLCMOS_IN_REG 0x7
+#define IDIO_24_COS_STATUS_BASE 0x8
+#define IDIO_24_CONTROL_REG 0xC
+#define IDIO_24_COS_ENABLE 0xE
+#define IDIO_24_SOFT_RESET 0xF
 
-/**
- * struct idio_24_gpio - GPIO device private data structure
- * @chip:	instance of the gpio_chip
- * @lock:	synchronization lock to prevent I/O race conditions
- * @reg:	I/O address offset for the GPIO device registers
- * @irq_mask:	I/O bits affected by interrupts
- */
-struct idio_24_gpio {
-	struct gpio_chip chip;
-	raw_spinlock_t lock;
-	__u8 __iomem *plx;
-	struct idio_24_gpio_reg __iomem *reg;
-	unsigned long irq_mask;
-};
-
-static int idio_24_gpio_get_direction(struct gpio_chip *chip,
-	unsigned int offset)
-{
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	const unsigned long out_mode_mask = BIT(1);
-
-	/* FET Outputs */
-	if (offset < 24)
-		return GPIO_LINE_DIRECTION_OUT;
+#define CONTROL_REG_OUT_MODE BIT(1)
 
-	/* Isolated Inputs */
-	if (offset < 48)
-		return GPIO_LINE_DIRECTION_IN;
+#define COS_ENABLE_RISING BIT(1)
+#define COS_ENABLE_FALLING BIT(4)
+#define COS_ENABLE_BOTH (COS_ENABLE_RISING | COS_ENABLE_FALLING)
 
-	/* TTL/CMOS I/O */
-	/* OUT MODE = 1 when TTL/CMOS Output Mode is set */
-	if (ioread8(&idio24gpio->reg->ctl) & out_mode_mask)
-		return GPIO_LINE_DIRECTION_OUT;
-
-	return GPIO_LINE_DIRECTION_IN;
-}
+static const struct regmap_range pex8311_intcsr_wr_ranges[] = {
+	regmap_reg_range(0x0, 0x0),
+};
+static const struct regmap_range pex8311_intcsr_rd_ranges[] = {
+	regmap_reg_range(0x0, 0x0),
+};
+static const struct regmap_range pex8311_intcsr_volatile_ranges[] = {
+	regmap_reg_range(0x0, 0x0),
+};
+static const struct regmap_access_table pex8311_intcsr_wr_table = {
+	.yes_ranges = pex8311_intcsr_wr_ranges,
+	.n_yes_ranges = ARRAY_SIZE(pex8311_intcsr_wr_ranges),
+};
+static const struct regmap_access_table pex8311_intcsr_rd_table = {
+	.yes_ranges = pex8311_intcsr_rd_ranges,
+	.n_yes_ranges = ARRAY_SIZE(pex8311_intcsr_rd_ranges),
+};
+static const struct regmap_access_table pex8311_intcsr_volatile_table = {
+	.yes_ranges = pex8311_intcsr_volatile_ranges,
+	.n_yes_ranges = ARRAY_SIZE(pex8311_intcsr_volatile_ranges),
+};
 
-static int idio_24_gpio_direction_input(struct gpio_chip *chip,
-	unsigned int offset)
-{
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	unsigned long flags;
-	unsigned int ctl_state;
-	const unsigned long out_mode_mask = BIT(1);
+static const struct regmap_config pex8311_intcsr_regmap_config = {
+	.name = "pex8311_intcsr",
+	.reg_bits = 32,
+	.reg_stride = 1,
+	.val_bits = 32,
+	.io_port = true,
+	.max_register = 0x0,
+	.wr_table = &pex8311_intcsr_wr_table,
+	.rd_table = &pex8311_intcsr_rd_table,
+	.volatile_table = &pex8311_intcsr_volatile_table,
+};
 
-	/* TTL/CMOS I/O */
-	if (offset > 47) {
-		raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+static const struct regmap_range idio_24_wr_ranges[] = {
+	regmap_reg_range(0x0, 0x3), regmap_reg_range(0x8, 0xC),
+	regmap_reg_range(0xE, 0xF),
+};
+static const struct regmap_range idio_24_rd_ranges[] = {
+	regmap_reg_range(0x0, 0xC), regmap_reg_range(0xE, 0xF),
+};
+static const struct regmap_range idio_24_volatile_ranges[] = {
+	regmap_reg_range(0x4, 0xB), regmap_reg_range(0xF, 0xF),
+};
+static const struct regmap_access_table idio_24_wr_table = {
+	.yes_ranges = idio_24_wr_ranges,
+	.n_yes_ranges = ARRAY_SIZE(idio_24_wr_ranges),
+};
+static const struct regmap_access_table idio_24_rd_table = {
+	.yes_ranges = idio_24_rd_ranges,
+	.n_yes_ranges = ARRAY_SIZE(idio_24_rd_ranges),
+};
+static const struct regmap_access_table idio_24_volatile_table = {
+	.yes_ranges = idio_24_volatile_ranges,
+	.n_yes_ranges = ARRAY_SIZE(idio_24_volatile_ranges),
+};
 
-		/* Clear TTL/CMOS Output Mode */
-		ctl_state = ioread8(&idio24gpio->reg->ctl) & ~out_mode_mask;
-		iowrite8(ctl_state, &idio24gpio->reg->ctl);
+static const struct regmap_config idio_24_regmap_config = {
+	.reg_bits = 8,
+	.reg_stride = 1,
+	.val_bits = 8,
+	.io_port = true,
+	.max_register = 0xF,
+	.wr_table = &idio_24_wr_table,
+	.rd_table = &idio_24_rd_table,
+	.volatile_table = &idio_24_volatile_table,
+	.cache_type = REGCACHE_FLAT,
+};
 
-		raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+#define IDIO_24_NGPIO_PER_REG 8
+#define IDIO_24_REGMAP_IRQ(_id)						\
+	[24 + _id] = {							\
+		.reg_offset = (_id) / IDIO_24_NGPIO_PER_REG,		\
+		.mask = BIT((_id) % IDIO_24_NGPIO_PER_REG),		\
+		.type = { .types_supported = IRQ_TYPE_EDGE_BOTH },	\
 	}
+#define IDIO_24_IIN_IRQ(_id) IDIO_24_REGMAP_IRQ(_id)
+#define IDIO_24_TTL_IRQ(_id) IDIO_24_REGMAP_IRQ(24 + _id)
+
+static const struct regmap_irq idio_24_regmap_irqs[] = {
+	IDIO_24_IIN_IRQ(0), IDIO_24_IIN_IRQ(1), IDIO_24_IIN_IRQ(2), /* IIN 0-2 */
+	IDIO_24_IIN_IRQ(3), IDIO_24_IIN_IRQ(4), IDIO_24_IIN_IRQ(5), /* IIN 3-5 */
+	IDIO_24_IIN_IRQ(6), IDIO_24_IIN_IRQ(7), IDIO_24_IIN_IRQ(8), /* IIN 6-8 */
+	IDIO_24_IIN_IRQ(9), IDIO_24_IIN_IRQ(10), IDIO_24_IIN_IRQ(11), /* IIN 9-11 */
+	IDIO_24_IIN_IRQ(12), IDIO_24_IIN_IRQ(13), IDIO_24_IIN_IRQ(14), /* IIN 12-14 */
+	IDIO_24_IIN_IRQ(15), IDIO_24_IIN_IRQ(16), IDIO_24_IIN_IRQ(17), /* IIN 15-17 */
+	IDIO_24_IIN_IRQ(18), IDIO_24_IIN_IRQ(19), IDIO_24_IIN_IRQ(20), /* IIN 18-20 */
+	IDIO_24_IIN_IRQ(21), IDIO_24_IIN_IRQ(22), IDIO_24_IIN_IRQ(23), /* IIN 21-23 */
+	IDIO_24_TTL_IRQ(0), IDIO_24_TTL_IRQ(1), IDIO_24_TTL_IRQ(2), /* TTL 0-2 */
+	IDIO_24_TTL_IRQ(3), IDIO_24_TTL_IRQ(4), IDIO_24_TTL_IRQ(5), /* TTL 3-5 */
+	IDIO_24_TTL_IRQ(6), IDIO_24_TTL_IRQ(7), /* TTL 6-7 */
+};
 
-	return 0;
-}
+/**
+ * struct idio_24_gpio - GPIO device private data structure
+ * @map:	regmap for the device
+ * @lock:	synchronization lock to prevent I/O race conditions
+ * @irq_type:	type configuration for IRQs
+ */
+struct idio_24_gpio {
+	struct regmap *map;
+	struct mutex lock;
+	u8 irq_type;
+};
 
-static int idio_24_gpio_direction_output(struct gpio_chip *chip,
-	unsigned int offset, int value)
+static int idio_24_set_type_config(unsigned int **const buf,
+				   const unsigned int type,
+				   const struct regmap_irq *const irq_data,
+				   const int idx, void *const irq_drv_data)
 {
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	unsigned long flags;
-	unsigned int ctl_state;
-	const unsigned long out_mode_mask = BIT(1);
-
-	/* TTL/CMOS I/O */
-	if (offset > 47) {
-		raw_spin_lock_irqsave(&idio24gpio->lock, flags);
-
-		/* Set TTL/CMOS Output Mode */
-		ctl_state = ioread8(&idio24gpio->reg->ctl) | out_mode_mask;
-		iowrite8(ctl_state, &idio24gpio->reg->ctl);
-
-		raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+	const unsigned int offset = irq_data->reg_offset;
+	const unsigned int rising = COS_ENABLE_RISING << offset;
+	const unsigned int falling = COS_ENABLE_FALLING << offset;
+	const unsigned int mask = COS_ENABLE_BOTH << offset;
+	struct idio_24_gpio *const idio24gpio = irq_drv_data;
+	unsigned int new;
+	unsigned int cos_enable;
+	int ret;
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		new = rising;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		new = falling;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		new = mask;
+		break;
+	default:
+		return -EINVAL;
 	}
 
-	chip->set(chip, offset, value);
-	return 0;
-}
-
-static int idio_24_gpio_get(struct gpio_chip *chip, unsigned int offset)
-{
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	const unsigned long offset_mask = BIT(offset % 8);
-	const unsigned long out_mode_mask = BIT(1);
+	mutex_lock(&idio24gpio->lock);
 
-	/* FET Outputs */
-	if (offset < 8)
-		return !!(ioread8(&idio24gpio->reg->out0_7) & offset_mask);
+	/* replace old bitmap with new bitmap */
+	idio24gpio->irq_type = (idio24gpio->irq_type & ~mask) | (new & mask);
 
-	if (offset < 16)
-		return !!(ioread8(&idio24gpio->reg->out8_15) & offset_mask);
+	ret = regmap_read(idio24gpio->map, IDIO_24_COS_ENABLE, &cos_enable);
+	if (ret)
+		goto exit_early;
 
-	if (offset < 24)
-		return !!(ioread8(&idio24gpio->reg->out16_23) & offset_mask);
-
-	/* Isolated Inputs */
-	if (offset < 32)
-		return !!(ioread8(&idio24gpio->reg->in0_7) & offset_mask);
-
-	if (offset < 40)
-		return !!(ioread8(&idio24gpio->reg->in8_15) & offset_mask);
-
-	if (offset < 48)
-		return !!(ioread8(&idio24gpio->reg->in16_23) & offset_mask);
-
-	/* TTL/CMOS Outputs */
-	if (ioread8(&idio24gpio->reg->ctl) & out_mode_mask)
-		return !!(ioread8(&idio24gpio->reg->ttl_out0_7) & offset_mask);
-
-	/* TTL/CMOS Inputs */
-	return !!(ioread8(&idio24gpio->reg->ttl_in0_7) & offset_mask);
-}
-
-static int idio_24_gpio_get_multiple(struct gpio_chip *chip,
-	unsigned long *mask, unsigned long *bits)
-{
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	unsigned long offset;
-	unsigned long gpio_mask;
-	void __iomem *ports[] = {
-		&idio24gpio->reg->out0_7, &idio24gpio->reg->out8_15,
-		&idio24gpio->reg->out16_23, &idio24gpio->reg->in0_7,
-		&idio24gpio->reg->in8_15, &idio24gpio->reg->in16_23,
-	};
-	size_t index;
-	unsigned long port_state;
-	const unsigned long out_mode_mask = BIT(1);
-
-	/* clear bits array to a clean slate */
-	bitmap_zero(bits, chip->ngpio);
-
-	for_each_set_clump8(offset, gpio_mask, mask, ARRAY_SIZE(ports) * 8) {
-		index = offset / 8;
-
-		/* read bits from current gpio port (port 6 is TTL GPIO) */
-		if (index < 6)
-			port_state = ioread8(ports[index]);
-		else if (ioread8(&idio24gpio->reg->ctl) & out_mode_mask)
-			port_state = ioread8(&idio24gpio->reg->ttl_out0_7);
-		else
-			port_state = ioread8(&idio24gpio->reg->ttl_in0_7);
-
-		port_state &= gpio_mask;
-
-		bitmap_set_value8(bits, port_state, offset);
+	/* if COS is currently enabled then update the edge type */
+	if (cos_enable & mask) {
+		ret = regmap_update_bits(idio24gpio->map, IDIO_24_COS_ENABLE,
+					 mask, idio24gpio->irq_type);
+		goto exit_early;
 	}
 
-	return 0;
-}
+exit_early:
+	mutex_unlock(&idio24gpio->lock);
 
-static void idio_24_gpio_set(struct gpio_chip *chip, unsigned int offset,
-	int value)
-{
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	const unsigned long out_mode_mask = BIT(1);
-	void __iomem *base;
-	const unsigned int mask = BIT(offset % 8);
-	unsigned long flags;
-	unsigned int out_state;
-
-	/* Isolated Inputs */
-	if (offset > 23 && offset < 48)
-		return;
-
-	/* TTL/CMOS Inputs */
-	if (offset > 47 && !(ioread8(&idio24gpio->reg->ctl) & out_mode_mask))
-		return;
-
-	/* TTL/CMOS Outputs */
-	if (offset > 47)
-		base = &idio24gpio->reg->ttl_out0_7;
-	/* FET Outputs */
-	else if (offset > 15)
-		base = &idio24gpio->reg->out16_23;
-	else if (offset > 7)
-		base = &idio24gpio->reg->out8_15;
-	else
-		base = &idio24gpio->reg->out0_7;
-
-	raw_spin_lock_irqsave(&idio24gpio->lock, flags);
-
-	if (value)
-		out_state = ioread8(base) | mask;
-	else
-		out_state = ioread8(base) & ~mask;
-
-	iowrite8(out_state, base);
-
-	raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+	return ret;
 }
 
-static void idio_24_gpio_set_multiple(struct gpio_chip *chip,
-	unsigned long *mask, unsigned long *bits)
+static int idio_24_handle_mask_sync(struct regmap *const map, const int index,
+				    const unsigned int mask_buf_def,
+				    const unsigned int mask_buf,
+				    void *const irq_drv_data)
 {
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	unsigned long offset;
-	unsigned long gpio_mask;
-	void __iomem *ports[] = {
-		&idio24gpio->reg->out0_7, &idio24gpio->reg->out8_15,
-		&idio24gpio->reg->out16_23
-	};
-	size_t index;
-	unsigned long bitmask;
-	unsigned long flags;
-	unsigned long out_state;
-	const unsigned long out_mode_mask = BIT(1);
-
-	for_each_set_clump8(offset, gpio_mask, mask, ARRAY_SIZE(ports) * 8) {
-		index = offset / 8;
-
-		bitmask = bitmap_get_value8(bits, offset) & gpio_mask;
-
-		raw_spin_lock_irqsave(&idio24gpio->lock, flags);
-
-		/* read bits from current gpio port (port 6 is TTL GPIO) */
-		if (index < 6) {
-			out_state = ioread8(ports[index]);
-		} else if (ioread8(&idio24gpio->reg->ctl) & out_mode_mask) {
-			out_state = ioread8(&idio24gpio->reg->ttl_out0_7);
-		} else {
-			/* skip TTL GPIO if set for input */
-			raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
-			continue;
-		}
+	const unsigned int type_mask = COS_ENABLE_BOTH << index;
+	struct idio_24_gpio *const idio24gpio = irq_drv_data;
+	u8 type;
+	int ret;
 
-		/* set requested bit states */
-		out_state &= ~gpio_mask;
-		out_state |= bitmask;
+	mutex_lock(&idio24gpio->lock);
 
-		/* write bits for current gpio port (port 6 is TTL GPIO) */
-		if (index < 6)
-			iowrite8(out_state, ports[index]);
-		else
-			iowrite8(out_state, &idio24gpio->reg->ttl_out0_7);
+	/* if all are masked, then disable interrupts, else set to type */
+	type = (mask_buf == mask_buf_def) ? ~type_mask : idio24gpio->irq_type;
 
-		raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
-	}
-}
+	ret = regmap_update_bits(map, IDIO_24_COS_ENABLE, type_mask, type);
 
-static void idio_24_irq_ack(struct irq_data *data)
-{
-}
-
-static void idio_24_irq_mask(struct irq_data *data)
-{
-	struct gpio_chip *const chip = irq_data_get_irq_chip_data(data);
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	unsigned long flags;
-	const unsigned long bit_offset = irqd_to_hwirq(data) - 24;
-	unsigned char new_irq_mask;
-	const unsigned long bank_offset = bit_offset / 8;
-	unsigned char cos_enable_state;
-
-	raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+	mutex_unlock(&idio24gpio->lock);
 
-	idio24gpio->irq_mask &= ~BIT(bit_offset);
-	new_irq_mask = idio24gpio->irq_mask >> bank_offset * 8;
-
-	if (!new_irq_mask) {
-		cos_enable_state = ioread8(&idio24gpio->reg->cos_enable);
-
-		/* Disable Rising Edge detection */
-		cos_enable_state &= ~BIT(bank_offset);
-		/* Disable Falling Edge detection */
-		cos_enable_state &= ~BIT(bank_offset + 4);
-
-		iowrite8(cos_enable_state, &idio24gpio->reg->cos_enable);
-	}
-
-	raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+	return ret;
 }
 
-static void idio_24_irq_unmask(struct irq_data *data)
+static int idio_24_reg_mask_xlate(struct gpio_regmap *const gpio,
+				  const unsigned int base,
+				  const unsigned int offset,
+				  unsigned int *const reg,
+				  unsigned int *const mask)
 {
-	struct gpio_chip *const chip = irq_data_get_irq_chip_data(data);
-	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
-	unsigned long flags;
-	unsigned char prev_irq_mask;
-	const unsigned long bit_offset = irqd_to_hwirq(data) - 24;
-	const unsigned long bank_offset = bit_offset / 8;
-	unsigned char cos_enable_state;
-
-	raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+	const unsigned int out_stride = offset / IDIO_24_NGPIO_PER_REG;
+	const unsigned int in_stride = (offset - 24) / IDIO_24_NGPIO_PER_REG;
+	struct regmap *const map = gpio_regmap_get_drvdata(gpio);
+	int err;
+	unsigned int ctrl_reg;
 
-	prev_irq_mask = idio24gpio->irq_mask >> bank_offset * 8;
-	idio24gpio->irq_mask |= BIT(bit_offset);
+	switch (base) {
+	case IDIO_24_OUT_BASE:
+		*mask = BIT(offset % IDIO_24_NGPIO_PER_REG);
 
-	if (!prev_irq_mask) {
-		cos_enable_state = ioread8(&idio24gpio->reg->cos_enable);
+		/* FET Outputs */
+		if (offset < 24) {
+			*reg = IDIO_24_OUT_BASE + out_stride;
+			return 0;
+		}
 
-		/* Enable Rising Edge detection */
-		cos_enable_state |= BIT(bank_offset);
-		/* Enable Falling Edge detection */
-		cos_enable_state |= BIT(bank_offset + 4);
+		/* Isolated Inputs */
+		if (offset < 48) {
+			*reg = IDIO_24_IN_BASE + in_stride;
+			return 0;
+		}
 
-		iowrite8(cos_enable_state, &idio24gpio->reg->cos_enable);
-	}
+		err = regmap_read(map, IDIO_24_CONTROL_REG, &ctrl_reg);
+		if (err)
+			return err;
 
-	raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
-}
+		/* TTL/CMOS Outputs */
+		if (ctrl_reg & CONTROL_REG_OUT_MODE) {
+			*reg = IDIO_24_TTLCMOS_OUT_REG;
+			return 0;
+		}
 
-static int idio_24_irq_set_type(struct irq_data *data, unsigned int flow_type)
-{
-	/* The only valid irq types are none and both-edges */
-	if (flow_type != IRQ_TYPE_NONE &&
-		(flow_type & IRQ_TYPE_EDGE_BOTH) != IRQ_TYPE_EDGE_BOTH)
+		/* TTL/CMOS Inputs */
+		*reg = IDIO_24_TTLCMOS_IN_REG;
+		return 0;
+	case IDIO_24_CONTROL_REG:
+		/* We can only set direction for TTL/CMOS lines */
+		if (offset < 48)
+			return -EOPNOTSUPP;
+
+		*reg = IDIO_24_CONTROL_REG;
+		*mask = CONTROL_REG_OUT_MODE;
+		return 0;
+	default:
+		/* Should never reach this path */
 		return -EINVAL;
-
-	return 0;
-}
-
-static struct irq_chip idio_24_irqchip = {
-	.name = "pcie-idio-24",
-	.irq_ack = idio_24_irq_ack,
-	.irq_mask = idio_24_irq_mask,
-	.irq_unmask = idio_24_irq_unmask,
-	.irq_set_type = idio_24_irq_set_type
-};
-
-static irqreturn_t idio_24_irq_handler(int irq, void *dev_id)
-{
-	struct idio_24_gpio *const idio24gpio = dev_id;
-	unsigned long irq_status;
-	struct gpio_chip *const chip = &idio24gpio->chip;
-	unsigned long irq_mask;
-	int gpio;
-
-	raw_spin_lock(&idio24gpio->lock);
-
-	/* Read Change-Of-State status */
-	irq_status = ioread32(&idio24gpio->reg->cos0_7);
-
-	raw_spin_unlock(&idio24gpio->lock);
-
-	/* Make sure our device generated IRQ */
-	if (!irq_status)
-		return IRQ_NONE;
-
-	/* Handle only unmasked IRQ */
-	irq_mask = idio24gpio->irq_mask & irq_status;
-
-	for_each_set_bit(gpio, &irq_mask, chip->ngpio - 24)
-		generic_handle_domain_irq(chip->irq.domain, gpio + 24);
-
-	raw_spin_lock(&idio24gpio->lock);
-
-	/* Clear Change-Of-State status */
-	iowrite32(irq_status, &idio24gpio->reg->cos0_7);
-
-	raw_spin_unlock(&idio24gpio->lock);
-
-	return IRQ_HANDLED;
+	}
 }
 
 #define IDIO_24_NGPIO 56
@@ -499,11 +335,12 @@  static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	const size_t pci_plx_bar_index = 1;
 	const size_t pci_bar_index = 2;
 	const char *const name = pci_name(pdev);
-	struct gpio_irq_chip *girq;
-
-	idio24gpio = devm_kzalloc(dev, sizeof(*idio24gpio), GFP_KERNEL);
-	if (!idio24gpio)
-		return -ENOMEM;
+	struct gpio_regmap_config gpio_config = {};
+	void __iomem *pex8311_intcsr;
+	void __iomem *idio_24_regs;
+	struct regmap *pex8311_intcsr_map;
+	struct regmap_irq_chip *chip;
+	struct regmap_irq_chip_data *chip_data;
 
 	err = pcim_enable_device(pdev);
 	if (err) {
@@ -517,57 +354,75 @@  static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		return err;
 	}
 
-	idio24gpio->plx = pcim_iomap_table(pdev)[pci_plx_bar_index];
-	idio24gpio->reg = pcim_iomap_table(pdev)[pci_bar_index];
-
-	idio24gpio->chip.label = name;
-	idio24gpio->chip.parent = dev;
-	idio24gpio->chip.owner = THIS_MODULE;
-	idio24gpio->chip.base = -1;
-	idio24gpio->chip.ngpio = IDIO_24_NGPIO;
-	idio24gpio->chip.names = idio_24_names;
-	idio24gpio->chip.get_direction = idio_24_gpio_get_direction;
-	idio24gpio->chip.direction_input = idio_24_gpio_direction_input;
-	idio24gpio->chip.direction_output = idio_24_gpio_direction_output;
-	idio24gpio->chip.get = idio_24_gpio_get;
-	idio24gpio->chip.get_multiple = idio_24_gpio_get_multiple;
-	idio24gpio->chip.set = idio_24_gpio_set;
-	idio24gpio->chip.set_multiple = idio_24_gpio_set_multiple;
-
-	girq = &idio24gpio->chip.irq;
-	girq->chip = &idio_24_irqchip;
-	/* This will let us handle the parent IRQ in the driver */
-	girq->parent_handler = NULL;
-	girq->num_parents = 0;
-	girq->parents = NULL;
-	girq->default_type = IRQ_TYPE_NONE;
-	girq->handler = handle_edge_irq;
-
-	raw_spin_lock_init(&idio24gpio->lock);
+	pex8311_intcsr = pcim_iomap_table(pdev)[pci_plx_bar_index] + PLX_PEX8311_PCI_LCS_INTCSR;
+	idio_24_regs = pcim_iomap_table(pdev)[pci_bar_index];
+
+	pex8311_intcsr_map = devm_regmap_init_mmio(dev, pex8311_intcsr,
+						   &pex8311_intcsr_regmap_config);
+	if (IS_ERR(pex8311_intcsr_map))
+		return dev_err_probe(dev, PTR_ERR(pex8311_intcsr_map),
+				     "Unable to initialize PEX8311 register map\n");
+	idio24gpio->map = devm_regmap_init_mmio(dev, idio_24_regs,
+					    &idio_24_regmap_config);
+	if (IS_ERR(idio24gpio->map))
+		return dev_err_probe(dev, PTR_ERR(idio24gpio->map),
+				     "Unable to initialize register map\n");
+
+	idio24gpio = devm_kzalloc(dev, sizeof(*idio24gpio), GFP_KERNEL);
+	if (!idio24gpio)
+		return -ENOMEM;
+
+	mutex_init(&idio24gpio->lock);
+
+	/* Initialize all IRQ type configuration to IRQ_TYPE_EDGE_BOTH */
+	idio24gpio->irq_type = GENMASK(7, 0);
+
+	chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->name = name;
+	chip->status_base = IDIO_24_COS_STATUS_BASE;
+	chip->mask_base = IDIO_24_COS_ENABLE;
+	chip->ack_base = IDIO_24_COS_STATUS_BASE;
+	chip->num_regs = 4;
+	chip->irqs = idio_24_regmap_irqs;
+	chip->num_irqs = ARRAY_SIZE(idio_24_regmap_irqs);
+	chip->handle_mask_sync = idio_24_handle_mask_sync;
+	chip->set_type_config = idio_24_set_type_config;
+	chip->irq_drv_data = idio24gpio;
 
 	/* Software board reset */
-	iowrite8(0, &idio24gpio->reg->soft_reset);
+	err = regmap_write(idio24gpio->map, IDIO_24_SOFT_RESET, 0);
+	if (err)
+		return err;
 	/*
 	 * enable PLX PEX8311 internal PCI wire interrupt and local interrupt
 	 * input
 	 */
-	iowrite8((INTCSR_INTERNAL_PCI_WIRE | INTCSR_LOCAL_INPUT) >> 8,
-		 idio24gpio->plx + PLX_PEX8311_PCI_LCS_INTCSR + 1);
-
-	err = devm_gpiochip_add_data(dev, &idio24gpio->chip, idio24gpio);
-	if (err) {
-		dev_err(dev, "GPIO registering failed (%d)\n", err);
+	err = regmap_update_bits(pex8311_intcsr_map, 0x0, IDIO_24_ENABLE_IRQ,
+				 IDIO_24_ENABLE_IRQ);
+	if (err)
 		return err;
-	}
-
-	err = devm_request_irq(dev, pdev->irq, idio_24_irq_handler, IRQF_SHARED,
-		name, idio24gpio);
-	if (err) {
-		dev_err(dev, "IRQ handler registering failed (%d)\n", err);
-		return err;
-	}
 
-	return 0;
+	err = devm_regmap_add_irq_chip(dev, idio24gpio->map, pdev->irq, 0, 0,
+				       chip, &chip_data);
+	if (err)
+		return dev_err_probe(dev, err, "IRQ registration failed\n");
+
+	gpio_config.parent = dev;
+	gpio_config.regmap = idio24gpio->map;
+	gpio_config.ngpio = IDIO_24_NGPIO;
+	gpio_config.names = idio_24_names;
+	gpio_config.reg_dat_base = GPIO_REGMAP_ADDR(IDIO_24_OUT_BASE);
+	gpio_config.reg_set_base = GPIO_REGMAP_ADDR(IDIO_24_OUT_BASE);
+	gpio_config.reg_dir_out_base = GPIO_REGMAP_ADDR(IDIO_24_CONTROL_REG);
+	gpio_config.ngpio_per_reg = IDIO_24_NGPIO_PER_REG;
+	gpio_config.irq_domain = regmap_irq_get_domain(chip_data);
+	gpio_config.reg_mask_xlate = idio_24_reg_mask_xlate;
+	gpio_config.drvdata = idio24gpio->map;
+
+	return PTR_ERR_OR_ZERO(devm_gpio_regmap_register(dev, &gpio_config));
 }
 
 static const struct pci_device_id idio_24_pci_dev_id[] = {