@@ -252,15 +252,42 @@ static int tegra_csi_s_stream(struct v4l2_subdev *subdev, int enable)
return ret;
}
+ if (csi_chan->mipi) {
+ ret = tegra_mipi_enable(csi_chan->mipi);
+ if (ret < 0) {
+ dev_err(csi->dev,
+ "failed to enable MIPI pads: %d\n",
+ ret);
+ goto rpm_put;
+ }
+
+ /*
+ * CSI MIPI pads PULLUP, PULLDN and TERM impedances
+ * need to be calibrated after power on.
+ * So, trigger the calibration start here and results
+ * will be latched and applied to the pads when link is
+ * in LP11 state during start of sensor streaming.
+ */
+ tegra_mipi_calibrate(csi_chan->mipi);
+ }
+
ret = csi->ops->csi_start_streaming(csi_chan);
if (ret < 0)
- goto rpm_put;
+ goto disable_mipi;
return 0;
}
csi->ops->csi_stop_streaming(csi_chan);
+disable_mipi:
+ if (csi_chan->mipi) {
+ ret = tegra_mipi_disable(csi_chan->mipi);
+ if (ret < 0)
+ dev_err(csi->dev,
+ "failed to disable MIPI pads: %d\n", ret);
+ }
+
rpm_put:
pm_runtime_put(csi->dev);
return ret;
@@ -294,6 +321,7 @@ static int tegra_csi_channel_alloc(struct tegra_csi *csi,
unsigned int num_pads)
{
struct tegra_csi_channel *chan;
+ int ret = 0;
chan = kzalloc(sizeof(*chan), GFP_KERNEL);
if (!chan)
@@ -312,7 +340,16 @@ static int tegra_csi_channel_alloc(struct tegra_csi *csi,
chan->pads[0].flags = MEDIA_PAD_FL_SOURCE;
}
- return 0;
+ if (IS_ENABLED(CONFIG_VIDEO_TEGRA_TPG))
+ return 0;
+
+ chan->mipi = tegra_mipi_request(csi->dev, node);
+ if (IS_ERR(chan->mipi)) {
+ ret = PTR_ERR(chan->mipi);
+ dev_err(csi->dev, "failed to get mipi device: %d\n", ret);
+ }
+
+ return ret;
}
static int tegra_csi_tpg_channels_alloc(struct tegra_csi *csi)
@@ -473,6 +510,9 @@ static void tegra_csi_channels_cleanup(struct tegra_csi *csi)
struct tegra_csi_channel *chan, *tmp;
list_for_each_entry_safe(chan, tmp, &csi->csi_chans, list) {
+ if (chan->mipi)
+ tegra_mipi_free(chan->mipi);
+
subdev = &chan->subdev;
if (subdev->dev) {
if (!IS_ENABLED(CONFIG_VIDEO_TEGRA_TPG))
@@ -50,6 +50,7 @@ struct tegra_csi;
* @framerate: active framerate for TPG
* @h_blank: horizontal blanking for TPG active format
* @v_blank: vertical blanking for TPG active format
+ * @mipi: mipi device for corresponding csi channel pads
*/
struct tegra_csi_channel {
struct list_head list;
@@ -65,6 +66,7 @@ struct tegra_csi_channel {
unsigned int framerate;
unsigned int h_blank;
unsigned int v_blank;
+ struct tegra_mipi_device *mipi;
};
/**
@@ -187,6 +187,7 @@ tegra_channel_get_remote_subdev(struct tegra_vi_channel *chan, bool sensor)
int tegra_channel_set_stream(struct tegra_vi_channel *chan, bool on)
{
struct v4l2_subdev *subdev;
+ struct tegra_csi_channel *csi_chan;
int ret;
/* stream CSI */
@@ -198,11 +199,28 @@ int tegra_channel_set_stream(struct tegra_vi_channel *chan, bool on)
if (IS_ENABLED(CONFIG_VIDEO_TEGRA_TPG))
return 0;
+ if (on)
+ csi_chan = v4l2_get_subdevdata(subdev);
+
subdev = tegra_channel_get_remote_subdev(chan, on);
ret = v4l2_subdev_call(subdev, video, s_stream, on);
if (on && ret < 0 && ret != -ENOIOCTLCMD)
return ret;
+ /*
+ * CSI subdev stream on triggers start of MIPI pads calibration.
+ * Calibration results are latched and applied to the pads when
+ * link is in LP11 state which will hapen during sensor streaming.
+ * So, wait for calibration to complete here.
+ */
+ if (on && csi_chan->mipi) {
+ ret = tegra_mipi_wait(csi_chan->mipi);
+ if (ret < 0)
+ dev_err(csi_chan->csi->dev,
+ "MIPI calibration failed: %d\n", ret);
+ return ret;
+ }
+
return 0;
}
CSI MIPI pads need to be enabled and calibrated for capturing from the external sensor or transmitter. MIPI CAL unit calibrates MIPI pads pull-up, pull-down and termination impedances. Calibration is done by co-work of MIPI BIAS pad and MIPI CAL control unit. Triggering calibration start can happen any time after MIPI pads are enabled but calibration results will be latched and applied to MIPI pads by MIPI CAL unit only when the link is in LP11 state and then calibration status register gets updated. This patch enables CSI MIPI pads and calibrates them during streaming. Tegra CSI receiver is able to catch the very first clock transition. So, CSI receiver is always enabled prior to sensor streaming and trigger of calibration start is done during CSI subdev streaming and status of calibration is verified after sensor stream on. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> --- drivers/staging/media/tegra-video/csi.c | 44 +++++++++++++++++++++++++++++++-- drivers/staging/media/tegra-video/csi.h | 2 ++ drivers/staging/media/tegra-video/vi.c | 18 ++++++++++++++ 3 files changed, 62 insertions(+), 2 deletions(-)