deleted file mode 100644
@@ -1,92 +0,0 @@
-* Ingenic JZ4780 NAND/ECC
-
-This file documents the device tree bindings for NAND flash devices on the
-JZ4780. NAND devices are connected to the NEMC controller (described in
-memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
-be children of the NEMC node.
-
-Required NAND controller device properties:
-- compatible: Should be one of:
- * ingenic,jz4740-nand
- * ingenic,jz4725b-nand
- * ingenic,jz4780-nand
-- reg: For each bank with a NAND chip attached, should specify a bank number,
- an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
-
-Optional NAND controller device properties:
-- ecc-engine: To make use of the hardware ECC controller, this
- property must contain a phandle for the ECC controller node. The required
- properties for this node are described below. If this is not specified,
- software ECC will be used instead.
-
-Optional children nodes:
-- Individual NAND chips are children of the NAND controller node.
-
-Required children node properties:
-- reg: An integer ranging from 1 to 6 representing the CS line to use.
-
-Optional children node properties:
-- nand-ecc-step-size: ECC block size in bytes.
-- nand-ecc-strength: ECC strength (max number of correctable bits).
-- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default
-- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false
-- rb-gpios: GPIO specifier for the busy pin.
-- wp-gpios: GPIO specifier for the write protect pin.
-
-Optional child node of NAND chip nodes:
-- partitions: see Documentation/devicetree/bindings/mtd/partition.txt
-
-Example:
-
-nemc: nemc@13410000 {
- ...
-
- nandc: nand-controller@1 {
- compatible = "ingenic,jz4780-nand";
- reg = <1 0 0x1000000>; /* Bank 1 */
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- ecc-engine = <&bch>;
-
- nand@1 {
- reg = <1>;
-
- nand-ecc-step-size = <1024>;
- nand-ecc-strength = <24>;
- nand-ecc-mode = "hw";
- nand-on-flash-bbt;
-
- rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>;
-
- partitions {
- #address-cells = <2>;
- #size-cells = <2>;
- ...
- }
- };
- };
-};
-
-The ECC controller is a separate SoC component used for error correction on
-NAND devices. The following is a description of the device properties for a
-ECC controller.
-
-Required ECC properties:
-- compatible: Should be one of:
- * ingenic,jz4740-ecc
- * ingenic,jz4725b-bch
- * ingenic,jz4780-bch
-- reg: Should specify the ECC controller registers location and length.
-- clocks: Clock for the ECC controller.
-
-Example:
-
-bch: bch@134d0000 {
- compatible = "ingenic,jz4780-bch";
- reg = <0x134d0000 0x10000>;
-
- clocks = <&cgu JZ4780_CLK_BCH>;
-};
new file mode 100644
@@ -0,0 +1,133 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/ingenic,nand.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic SoCs NAND controller devicetree bindings
+
+maintainers:
+ - Paul Cercueil <paul@crapouillou.net>
+
+allOf:
+ - $ref: ../memory-controllers/ingenic,nemc-client.yaml#
+ - $ref: nand-controller.yaml#
+
+properties:
+ compatible:
+ enum:
+ - ingenic,jz4740-nand
+ - ingenic,jz4725b-nand
+ - ingenic,jz4780-nand
+
+ reg:
+ items:
+ - description: Bank number, offset and size of first attached NAND chip
+ - description: Bank number, offset and size of second attached NAND chip
+ - description: Bank number, offset and size of third attached NAND chip
+ - description: Bank number, offset and size of fourth attached NAND chip
+ minItems: 1
+
+ ecc-engine: true
+
+patternProperties:
+ "^nand@[a-f0-9]$":
+ type: object
+ properties:
+ rb-gpios:
+ description: GPIO specifier for the busy pin.
+ maxItems: 1
+
+ wp-gpios:
+ description: GPIO specifier for the write-protect pin.
+ maxItems: 1
+
+ "^partitions$":
+ type: object
+ description:
+ Node containing description of fixed partitions.
+ See Documentation/devicetree/bindings/mtd/partition.txt
+
+required:
+ - compatible
+ - reg
+
+examples:
+ - |
+ #include <dt-bindings/clock/jz4780-cgu.h>
+ nemc: memory-controller@13410000 {
+ compatible = "ingenic,jz4780-nemc";
+ reg = <0x13410000 0x10000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <1 0 0x1b000000 0x1000000>,
+ <2 0 0x1a000000 0x1000000>,
+ <3 0 0x19000000 0x1000000>,
+ <4 0 0x18000000 0x1000000>,
+ <5 0 0x17000000 0x1000000>,
+ <6 0 0x16000000 0x1000000>;
+
+ clocks = <&cgu JZ4780_CLK_NEMC>;
+
+ nand-controller@1 {
+ compatible = "ingenic,jz4780-nand";
+ reg = <1 0 0x1000000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ecc-engine = <&bch>;
+
+ ingenic,nemc-tAS = <10>;
+ ingenic,nemc-tAH = <5>;
+ ingenic,nemc-tBP = <10>;
+ ingenic,nemc-tAW = <15>;
+ ingenic,nemc-tSTRV = <100>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_nemc>;
+
+ nand@1 {
+ reg = <1>;
+
+ nand-ecc-step-size = <1024>;
+ nand-ecc-strength = <24>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_nemc_cs1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ partition@0 {
+ label = "u-boot-spl";
+ reg = <0x0 0x0 0x0 0x800000>;
+ };
+
+ partition@800000 {
+ label = "u-boot";
+ reg = <0x0 0x800000 0x0 0x200000>;
+ };
+
+ partition@a00000 {
+ label = "u-boot-env";
+ reg = <0x0 0xa00000 0x0 0x200000>;
+ };
+
+ partition@c00000 {
+ label = "boot";
+ reg = <0x0 0xc00000 0x0 0x4000000>;
+ };
+
+ partition@4c00000 {
+ label = "system";
+ reg = <0x0 0x4c00000 0x1 0xfb400000>;
+ };
+ };
+ };
+ };
+ };
Convert the ingenic,jz4780-nand.txt doc file to ingenic,nand.yaml. Signed-off-by: Paul Cercueil <paul@crapouillou.net> --- .../bindings/mtd/ingenic,jz4780-nand.txt | 92 ------------ .../devicetree/bindings/mtd/ingenic,nand.yaml | 133 ++++++++++++++++++ 2 files changed, 133 insertions(+), 92 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt create mode 100644 Documentation/devicetree/bindings/mtd/ingenic,nand.yaml