@@ -293,8 +293,6 @@ struct tegra_i2c_dev {
bool is_curr_atomic_xfer;
};
-static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev, bool clk_reinit);
-
static void dvc_writel(struct tegra_i2c_dev *i2c_dev, u32 val,
unsigned long reg)
{
@@ -473,186 +471,6 @@ static int tegra_i2c_init_dma(struct tegra_i2c_dev *i2c_dev)
return err;
}
-static int tegra_i2c_flush_fifos(struct tegra_i2c_dev *i2c_dev)
-{
- ktime_t ktime, ktimeout;
- unsigned int offset;
- u32 mask, val;
-
- if (i2c_dev->hw->has_mst_fifo) {
- mask = I2C_MST_FIFO_CONTROL_TX_FLUSH |
- I2C_MST_FIFO_CONTROL_RX_FLUSH;
- offset = I2C_MST_FIFO_CONTROL;
- } else {
- mask = I2C_FIFO_CONTROL_TX_FLUSH |
- I2C_FIFO_CONTROL_RX_FLUSH;
- offset = I2C_FIFO_CONTROL;
- }
-
- val = i2c_readl(i2c_dev, offset);
- val |= mask;
- i2c_writel(i2c_dev, val, offset);
-
- /*
- * ktime_get() may take up to couple milliseconds in a worst case
- * and normally FIFOs are flushed, hence let's check the state before
- * proceeding to polling.
- */
- if (!(i2c_readl(i2c_dev, offset) & mask))
- return 0;
-
- ktime = ktime_get();
- ktimeout = ktime_add_ms(ktime, 1000);
-
- while (i2c_readl(i2c_dev, offset) & mask) {
- if (ktime_after(ktime, ktimeout))
- goto err_timeout;
-
- if (i2c_dev->is_curr_atomic_xfer)
- mdelay(1);
- else
- fsleep(1000);
-
- ktime = ktime_get();
- }
-
- return 0;
-
-err_timeout:
- dev_err(i2c_dev->dev, "FIFO flushing timed out\n");
-
- return -ETIMEDOUT;
-}
-
-static int tegra_i2c_empty_rx_fifo(struct tegra_i2c_dev *i2c_dev)
-{
- size_t buf_remaining = i2c_dev->msg_buf_remaining;
- u8 *buf = i2c_dev->msg_buf;
- int words_to_transfer;
- int rx_fifo_avail;
- u32 val;
-
- /*
- * Catch overflow due to message fully sent
- * before the check for RX FIFO availability.
- */
- if (WARN_ON_ONCE(!(i2c_dev->msg_buf_remaining)))
- return -EINVAL;
-
- if (i2c_dev->hw->has_mst_fifo) {
- val = i2c_readl(i2c_dev, I2C_MST_FIFO_STATUS);
- rx_fifo_avail = FIELD_GET(I2C_MST_FIFO_STATUS_RX, val);
- } else {
- val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
- rx_fifo_avail = FIELD_GET(I2C_FIFO_STATUS_RX, val);
- }
-
- /* Rounds down to not include partial word at the end of buf */
- words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD;
- if (words_to_transfer > rx_fifo_avail)
- words_to_transfer = rx_fifo_avail;
-
- i2c_readsl(i2c_dev, buf, I2C_RX_FIFO, words_to_transfer);
-
- buf += words_to_transfer * BYTES_PER_FIFO_WORD;
- buf_remaining -= words_to_transfer * BYTES_PER_FIFO_WORD;
- rx_fifo_avail -= words_to_transfer;
-
- /*
- * If there is a partial word at the end of buf, handle it manually to
- * prevent overwriting past the end of buf
- */
- if (rx_fifo_avail > 0 && buf_remaining > 0) {
- /*
- * buf_remaining > 3 check not needed as rx_fifo_avail == 0
- * when (words_to_transfer was > rx_fifo_avail) earlier
- * in this function.
- */
- val = i2c_readl(i2c_dev, I2C_RX_FIFO);
- val = cpu_to_le32(val);
- memcpy(buf, &val, buf_remaining);
- buf_remaining = 0;
- rx_fifo_avail--;
- }
-
- /* RX FIFO must be drained, otherwise it's an Overflow case. */
- if (WARN_ON_ONCE(rx_fifo_avail))
- return -EINVAL;
-
- i2c_dev->msg_buf_remaining = buf_remaining;
- i2c_dev->msg_buf = buf;
-
- return 0;
-}
-
-static int tegra_i2c_fill_tx_fifo(struct tegra_i2c_dev *i2c_dev)
-{
- size_t buf_remaining = i2c_dev->msg_buf_remaining;
- u8 *buf = i2c_dev->msg_buf;
- int words_to_transfer;
- int tx_fifo_avail;
- u32 val;
-
- if (i2c_dev->hw->has_mst_fifo) {
- val = i2c_readl(i2c_dev, I2C_MST_FIFO_STATUS);
- tx_fifo_avail = FIELD_GET(I2C_MST_FIFO_STATUS_TX, val);
- } else {
- val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
- tx_fifo_avail = FIELD_GET(I2C_FIFO_STATUS_TX, val);
- }
-
- /* Rounds down to not include partial word at the end of buf */
- words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD;
-
- /* It's very common to have < 4 bytes, so optimize that case. */
- if (words_to_transfer) {
- if (words_to_transfer > tx_fifo_avail)
- words_to_transfer = tx_fifo_avail;
-
- /*
- * Update state before writing to FIFO. If this casues us
- * to finish writing all bytes (AKA buf_remaining goes to 0) we
- * have a potential for an interrupt (PACKET_XFER_COMPLETE is
- * not maskable). We need to make sure that the isr sees
- * buf_remaining as 0 and doesn't call us back re-entrantly.
- */
- buf_remaining -= words_to_transfer * BYTES_PER_FIFO_WORD;
- tx_fifo_avail -= words_to_transfer;
- i2c_dev->msg_buf_remaining = buf_remaining;
- i2c_dev->msg_buf = buf +
- words_to_transfer * BYTES_PER_FIFO_WORD;
- barrier();
-
- i2c_writesl(i2c_dev, buf, I2C_TX_FIFO, words_to_transfer);
-
- buf += words_to_transfer * BYTES_PER_FIFO_WORD;
- }
-
- /*
- * If there is a partial word at the end of buf, handle it manually to
- * prevent reading past the end of buf, which could cross a page
- * boundary and fault.
- */
- if (tx_fifo_avail > 0 && buf_remaining > 0) {
- /*
- * buf_remaining > 3 check not needed as tx_fifo_avail == 0
- * when (words_to_transfer was > tx_fifo_avail) earlier
- * in this function for non-zero words_to_transfer.
- */
- memcpy(&val, buf, buf_remaining);
- val = le32_to_cpu(val);
-
- /* Again update before writing to FIFO to make sure isr sees. */
- i2c_dev->msg_buf_remaining = 0;
- i2c_dev->msg_buf = NULL;
- barrier();
-
- i2c_writel(i2c_dev, val, I2C_TX_FIFO);
- }
-
- return 0;
-}
-
/*
* One of the Tegra I2C blocks is inside the DVC (Digital Voltage Controller)
* block. This block is identical to the rest of the I2C blocks, except that
@@ -674,66 +492,33 @@ static void tegra_dvc_init(struct tegra_i2c_dev *i2c_dev)
dvc_writel(i2c_dev, val, DVC_CTRL_REG1);
}
-static int __maybe_unused tegra_i2c_runtime_resume(struct device *dev)
+static void tegra_i2c_vi_init(struct tegra_i2c_dev *i2c_dev)
{
- struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
- int ret;
-
- ret = pinctrl_pm_select_default_state(i2c_dev->dev);
- if (ret)
- return ret;
-
- ret = clk_enable(i2c_dev->fast_clk);
- if (ret) {
- dev_err(dev, "failed to enable fast clock: %d\n", ret);
- return ret;
- }
-
- ret = clk_enable(i2c_dev->slow_clk);
- if (ret) {
- dev_err(dev, "failed to enable slow clock: %d\n", ret);
- goto disable_fast_clk;
- }
-
- ret = clk_enable(i2c_dev->div_clk);
- if (ret) {
- dev_err(dev, "failed to enable div clock: %d\n", ret);
- goto disable_slow_clk;
- }
-
- /*
- * VI I2C device is attached to VE power domain which goes through
- * power ON/OFF during PM runtime resume/suspend. So, controller
- * should go through reset and need to re-initialize after power
- * domain ON.
- */
- if (i2c_dev->is_vi) {
- ret = tegra_i2c_init(i2c_dev, true);
- if (ret)
- goto disable_div_clk;
- }
+ u32 value;
- return 0;
+ value = FIELD_PREP(I2C_INTERFACE_TIMING_THIGH, 2) |
+ FIELD_PREP(I2C_INTERFACE_TIMING_TLOW, 4);
+ i2c_writel(i2c_dev, value, I2C_INTERFACE_TIMING_0);
-disable_div_clk:
- clk_disable(i2c_dev->div_clk);
-disable_slow_clk:
- clk_disable(i2c_dev->slow_clk);
-disable_fast_clk:
- clk_disable(i2c_dev->fast_clk);
+ value = FIELD_PREP(I2C_INTERFACE_TIMING_TBUF, 4) |
+ FIELD_PREP(I2C_INTERFACE_TIMING_TSU_STO, 7) |
+ FIELD_PREP(I2C_INTERFACE_TIMING_THD_STA, 4) |
+ FIELD_PREP(I2C_INTERFACE_TIMING_TSU_STA, 4);
+ i2c_writel(i2c_dev, value, I2C_INTERFACE_TIMING_1);
- return ret;
-}
+ value = FIELD_PREP(I2C_HS_INTERFACE_TIMING_THIGH, 3) |
+ FIELD_PREP(I2C_HS_INTERFACE_TIMING_TLOW, 8);
+ i2c_writel(i2c_dev, value, I2C_HS_INTERFACE_TIMING_0);
-static int __maybe_unused tegra_i2c_runtime_suspend(struct device *dev)
-{
- struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
+ value = FIELD_PREP(I2C_HS_INTERFACE_TIMING_TSU_STO, 11) |
+ FIELD_PREP(I2C_HS_INTERFACE_TIMING_THD_STA, 11) |
+ FIELD_PREP(I2C_HS_INTERFACE_TIMING_TSU_STA, 11);
+ i2c_writel(i2c_dev, value, I2C_HS_INTERFACE_TIMING_1);
- clk_disable(i2c_dev->div_clk);
- clk_disable(i2c_dev->slow_clk);
- clk_disable(i2c_dev->fast_clk);
+ value = FIELD_PREP(I2C_BC_SCLK_THRESHOLD, 9) | I2C_BC_STOP_COND;
+ i2c_writel(i2c_dev, value, I2C_BUS_CLEAR_CNFG);
- return pinctrl_pm_select_idle_state(i2c_dev->dev);
+ i2c_writel(i2c_dev, 0x0, I2C_TLOW_SEXT);
}
static int tegra_i2c_wait_for_config_load(struct tegra_i2c_dev *i2c_dev)
@@ -765,33 +550,55 @@ static int tegra_i2c_wait_for_config_load(struct tegra_i2c_dev *i2c_dev)
return 0;
}
-static void tegra_i2c_vi_init(struct tegra_i2c_dev *i2c_dev)
+static int tegra_i2c_flush_fifos(struct tegra_i2c_dev *i2c_dev)
{
- u32 value;
+ ktime_t ktime, ktimeout;
+ unsigned int offset;
+ u32 mask, val;
- value = FIELD_PREP(I2C_INTERFACE_TIMING_THIGH, 2) |
- FIELD_PREP(I2C_INTERFACE_TIMING_TLOW, 4);
- i2c_writel(i2c_dev, value, I2C_INTERFACE_TIMING_0);
+ if (i2c_dev->hw->has_mst_fifo) {
+ mask = I2C_MST_FIFO_CONTROL_TX_FLUSH |
+ I2C_MST_FIFO_CONTROL_RX_FLUSH;
+ offset = I2C_MST_FIFO_CONTROL;
+ } else {
+ mask = I2C_FIFO_CONTROL_TX_FLUSH |
+ I2C_FIFO_CONTROL_RX_FLUSH;
+ offset = I2C_FIFO_CONTROL;
+ }
- value = FIELD_PREP(I2C_INTERFACE_TIMING_TBUF, 4) |
- FIELD_PREP(I2C_INTERFACE_TIMING_TSU_STO, 7) |
- FIELD_PREP(I2C_INTERFACE_TIMING_THD_STA, 4) |
- FIELD_PREP(I2C_INTERFACE_TIMING_TSU_STA, 4);
- i2c_writel(i2c_dev, value, I2C_INTERFACE_TIMING_1);
+ val = i2c_readl(i2c_dev, offset);
+ val |= mask;
+ i2c_writel(i2c_dev, val, offset);
+
+ /*
+ * ktime_get() may take up to couple milliseconds in a worst case
+ * and normally FIFOs are flushed, hence let's check the state before
+ * proceeding to polling.
+ */
+ if (!(i2c_readl(i2c_dev, offset) & mask))
+ return 0;
+
+ ktime = ktime_get();
+ ktimeout = ktime_add_ms(ktime, 1000);
+
+ while (i2c_readl(i2c_dev, offset) & mask) {
+ if (ktime_after(ktime, ktimeout))
+ goto err_timeout;
- value = FIELD_PREP(I2C_HS_INTERFACE_TIMING_THIGH, 3) |
- FIELD_PREP(I2C_HS_INTERFACE_TIMING_TLOW, 8);
- i2c_writel(i2c_dev, value, I2C_HS_INTERFACE_TIMING_0);
+ if (i2c_dev->is_curr_atomic_xfer)
+ mdelay(1);
+ else
+ fsleep(1000);
- value = FIELD_PREP(I2C_HS_INTERFACE_TIMING_TSU_STO, 11) |
- FIELD_PREP(I2C_HS_INTERFACE_TIMING_THD_STA, 11) |
- FIELD_PREP(I2C_HS_INTERFACE_TIMING_TSU_STA, 11);
- i2c_writel(i2c_dev, value, I2C_HS_INTERFACE_TIMING_1);
+ ktime = ktime_get();
+ }
- value = FIELD_PREP(I2C_BC_SCLK_THRESHOLD, 9) | I2C_BC_STOP_COND;
- i2c_writel(i2c_dev, value, I2C_BUS_CLEAR_CNFG);
+ return 0;
- i2c_writel(i2c_dev, 0x0, I2C_TLOW_SEXT);
+err_timeout:
+ dev_err(i2c_dev->dev, "FIFO flushing timed out\n");
+
+ return -ETIMEDOUT;
}
static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev, bool clk_reinit)
@@ -903,6 +710,135 @@ static int tegra_i2c_disable_packet_mode(struct tegra_i2c_dev *i2c_dev)
return tegra_i2c_wait_for_config_load(i2c_dev);
}
+static int tegra_i2c_empty_rx_fifo(struct tegra_i2c_dev *i2c_dev)
+{
+ size_t buf_remaining = i2c_dev->msg_buf_remaining;
+ u8 *buf = i2c_dev->msg_buf;
+ int words_to_transfer;
+ int rx_fifo_avail;
+ u32 val;
+
+ /*
+ * Catch overflow due to message fully sent
+ * before the check for RX FIFO availability.
+ */
+ if (WARN_ON_ONCE(!(i2c_dev->msg_buf_remaining)))
+ return -EINVAL;
+
+ if (i2c_dev->hw->has_mst_fifo) {
+ val = i2c_readl(i2c_dev, I2C_MST_FIFO_STATUS);
+ rx_fifo_avail = FIELD_GET(I2C_MST_FIFO_STATUS_RX, val);
+ } else {
+ val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
+ rx_fifo_avail = FIELD_GET(I2C_FIFO_STATUS_RX, val);
+ }
+
+ /* Rounds down to not include partial word at the end of buf */
+ words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD;
+ if (words_to_transfer > rx_fifo_avail)
+ words_to_transfer = rx_fifo_avail;
+
+ i2c_readsl(i2c_dev, buf, I2C_RX_FIFO, words_to_transfer);
+
+ buf += words_to_transfer * BYTES_PER_FIFO_WORD;
+ buf_remaining -= words_to_transfer * BYTES_PER_FIFO_WORD;
+ rx_fifo_avail -= words_to_transfer;
+
+ /*
+ * If there is a partial word at the end of buf, handle it manually to
+ * prevent overwriting past the end of buf
+ */
+ if (rx_fifo_avail > 0 && buf_remaining > 0) {
+ /*
+ * buf_remaining > 3 check not needed as rx_fifo_avail == 0
+ * when (words_to_transfer was > rx_fifo_avail) earlier
+ * in this function.
+ */
+ val = i2c_readl(i2c_dev, I2C_RX_FIFO);
+ val = cpu_to_le32(val);
+ memcpy(buf, &val, buf_remaining);
+ buf_remaining = 0;
+ rx_fifo_avail--;
+ }
+
+ /* RX FIFO must be drained, otherwise it's an Overflow case. */
+ if (WARN_ON_ONCE(rx_fifo_avail))
+ return -EINVAL;
+
+ i2c_dev->msg_buf_remaining = buf_remaining;
+ i2c_dev->msg_buf = buf;
+
+ return 0;
+}
+
+static int tegra_i2c_fill_tx_fifo(struct tegra_i2c_dev *i2c_dev)
+{
+ size_t buf_remaining = i2c_dev->msg_buf_remaining;
+ u8 *buf = i2c_dev->msg_buf;
+ int words_to_transfer;
+ int tx_fifo_avail;
+ u32 val;
+
+ if (i2c_dev->hw->has_mst_fifo) {
+ val = i2c_readl(i2c_dev, I2C_MST_FIFO_STATUS);
+ tx_fifo_avail = FIELD_GET(I2C_MST_FIFO_STATUS_TX, val);
+ } else {
+ val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
+ tx_fifo_avail = FIELD_GET(I2C_FIFO_STATUS_TX, val);
+ }
+
+ /* Rounds down to not include partial word at the end of buf */
+ words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD;
+
+ /* It's very common to have < 4 bytes, so optimize that case. */
+ if (words_to_transfer) {
+ if (words_to_transfer > tx_fifo_avail)
+ words_to_transfer = tx_fifo_avail;
+
+ /*
+ * Update state before writing to FIFO. If this casues us
+ * to finish writing all bytes (AKA buf_remaining goes to 0) we
+ * have a potential for an interrupt (PACKET_XFER_COMPLETE is
+ * not maskable). We need to make sure that the isr sees
+ * buf_remaining as 0 and doesn't call us back re-entrantly.
+ */
+ buf_remaining -= words_to_transfer * BYTES_PER_FIFO_WORD;
+ tx_fifo_avail -= words_to_transfer;
+ i2c_dev->msg_buf_remaining = buf_remaining;
+ i2c_dev->msg_buf = buf +
+ words_to_transfer * BYTES_PER_FIFO_WORD;
+ barrier();
+
+ i2c_writesl(i2c_dev, buf, I2C_TX_FIFO, words_to_transfer);
+
+ buf += words_to_transfer * BYTES_PER_FIFO_WORD;
+ }
+
+ /*
+ * If there is a partial word at the end of buf, handle it manually to
+ * prevent reading past the end of buf, which could cross a page
+ * boundary and fault.
+ */
+ if (tx_fifo_avail > 0 && buf_remaining > 0) {
+ /*
+ * buf_remaining > 3 check not needed as tx_fifo_avail == 0
+ * when (words_to_transfer was > tx_fifo_avail) earlier
+ * in this function for non-zero words_to_transfer.
+ */
+ memcpy(&val, buf, buf_remaining);
+ val = le32_to_cpu(val);
+
+ /* Again update before writing to FIFO to make sure isr sees. */
+ i2c_dev->msg_buf_remaining = 0;
+ i2c_dev->msg_buf = NULL;
+ barrier();
+
+ i2c_writel(i2c_dev, val, I2C_TX_FIFO);
+ }
+
+ return 0;
+}
+
static irqreturn_t tegra_i2c_isr(int irq, void *dev_id)
{
const u32 status_err = I2C_INT_NO_ACK | I2C_INT_ARBITRATION_LOST;
@@ -1454,27 +1390,6 @@ static u32 tegra_i2c_func(struct i2c_adapter *adap)
return ret;
}
-static int tegra_i2c_parse_dt(struct tegra_i2c_dev *i2c_dev)
-{
- struct device_node *np = i2c_dev->dev->of_node;
- u32 bus_clk_rate = I2C_MAX_STANDARD_MODE_FREQ;
- bool multi_mode;
-
- of_property_read_u32(np, "clock-frequency", &bus_clk_rate);
- i2c_dev->bus_clk_rate = bus_clk_rate;
-
- multi_mode = of_property_read_bool(np, "multi-master");
- i2c_dev->is_multimaster_mode = multi_mode;
-
- if (of_device_is_compatible(np, "nvidia,tegra20-i2c-dvc"))
- i2c_dev->is_dvc = true;
-
- if (of_device_is_compatible(np, "nvidia,tegra210-i2c-vi"))
- i2c_dev->is_vi = true;
-
- return 0;
-}
-
static const struct i2c_algorithm tegra_i2c_algo = {
.master_xfer = tegra_i2c_xfer,
.master_xfer_atomic = tegra_i2c_xfer_atomic,
@@ -1687,6 +1602,27 @@ static const struct of_device_id tegra_i2c_of_match[] = {
};
MODULE_DEVICE_TABLE(of, tegra_i2c_of_match);
+static int tegra_i2c_parse_dt(struct tegra_i2c_dev *i2c_dev)
+{
+ struct device_node *np = i2c_dev->dev->of_node;
+ u32 bus_clk_rate = I2C_MAX_STANDARD_MODE_FREQ;
+ bool multi_mode;
+
+ of_property_read_u32(np, "clock-frequency", &bus_clk_rate);
+ i2c_dev->bus_clk_rate = bus_clk_rate;
+
+ multi_mode = of_property_read_bool(np, "multi-master");
+ i2c_dev->is_multimaster_mode = multi_mode;
+
+ if (of_device_is_compatible(np, "nvidia,tegra20-i2c-dvc"))
+ i2c_dev->is_dvc = true;
+
+ if (of_device_is_compatible(np, "nvidia,tegra210-i2c-vi"))
+ i2c_dev->is_vi = true;
+
+ return 0;
+}
+
static int tegra_i2c_init_clocks(struct tegra_i2c_dev *i2c_dev)
{
const struct tegra_i2c_hw_feature *hw = i2c_dev->hw;
@@ -1930,6 +1866,68 @@ static int tegra_i2c_remove(struct platform_device *pdev)
return 0;
}
+static int __maybe_unused tegra_i2c_runtime_resume(struct device *dev)
+{
+ struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
+ int ret;
+
+ ret = pinctrl_pm_select_default_state(i2c_dev->dev);
+ if (ret)
+ return ret;
+
+ ret = clk_enable(i2c_dev->fast_clk);
+ if (ret) {
+ dev_err(dev, "failed to enable fast clock: %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_enable(i2c_dev->slow_clk);
+ if (ret) {
+ dev_err(dev, "failed to enable slow clock: %d\n", ret);
+ goto disable_fast_clk;
+ }
+
+ ret = clk_enable(i2c_dev->div_clk);
+ if (ret) {
+ dev_err(dev, "failed to enable div clock: %d\n", ret);
+ goto disable_slow_clk;
+ }
+
+ /*
+ * VI I2C device is attached to VE power domain which goes through
+ * power ON/OFF during PM runtime resume/suspend. So, controller
+ * should go through reset and need to re-initialize after power
+ * domain ON.
+ */
+ if (i2c_dev->is_vi) {
+ ret = tegra_i2c_init(i2c_dev, true);
+ if (ret)
+ goto disable_div_clk;
+ }
+
+ return 0;
+
+disable_div_clk:
+ clk_disable(i2c_dev->div_clk);
+disable_slow_clk:
+ clk_disable(i2c_dev->slow_clk);
+disable_fast_clk:
+ clk_disable(i2c_dev->fast_clk);
+
+ return ret;
+}
+
+static int __maybe_unused tegra_i2c_runtime_suspend(struct device *dev)
+{
+ struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
+
+ clk_disable(i2c_dev->div_clk);
+ clk_disable(i2c_dev->slow_clk);
+ clk_disable(i2c_dev->fast_clk);
+
+ return pinctrl_pm_select_idle_state(i2c_dev->dev);
+}
+
static int __maybe_unused tegra_i2c_suspend(struct device *dev)
{
struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
Reorder location of functions in the code in order to have definition of functions closer to the place of the invocation. This change makes easier to navigate around the code and removes the need to have a prototype for tegra_i2c_init(). Signed-off-by: Dmitry Osipenko <digetx@gmail.com> --- drivers/i2c/busses/i2c-tegra.c | 550 ++++++++++++++++----------------- 1 file changed, 274 insertions(+), 276 deletions(-)