diff mbox series

[v2,02/12] i2c: designware: Empty receive FIFO in slave interrupt handler

Message ID 20221102131125.421512-3-jarkko.nikula@linux.intel.com
State Superseded
Headers show
Series i2c: designware: Slave fixes and generic cleanups | expand

Commit Message

Jarkko Nikula Nov. 2, 2022, 1:11 p.m. UTC
Writes from I2C bus often fail when testing the i2c-designware-slave.c
with the slave-eeprom backend. The same writes work correctly when
testing with a real 24c02 EEPROM chip.

In the tests below an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6.

1. i2cset -y 6 0x65 0x00 0x55

Single byte 0x55 write into address 0x00. No data goes into simulated
EEPROM. Debug prints from the i2c_dw_irq_handler_slave():

0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4

2. i2ctransfer -y 6 w9@0x65 0x00 0xff-

Write 8 bytes with decrementing value starting from 0xff at address 0x00
and forward. Only some of the data goes into arbitrary addresses.
Content is something like below but varies:

00000000  f9 f8 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
00000050  00 00 00 00 00 00 ff fe  00 00 00 00 00 00 00 00  |................|
000000f0  00 00 00 00 00 00 00 00  00 00 00 00 00 fc fb fa  |................|

In this case debug prints were:

0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x510 : INTR_STAT=0x0

Both cases show there is more data coming from the receive FIFO still
after detecting the STOP condition. This can be seen from interrupt
status bits DW_IC_INTR_STOP_DET (0x200) and DW_IC_INTR_RX_FULL (0x4).

Perhaps due interrupt latencies the receive FIFO is not read fast
enough, STOP detection happens synchronously when it occurs on the I2C
bus and the DW_IC_INTR_RX_FULL keeps coming as long as there are more
bytes in the receive FIFO.

Fix this by reading the receive FIFO completely empty whenever
DW_IC_INTR_RX_FULL occurs. Use RFNE, Receive FIFO Not Empty bit in the
DW_IC_STATUS register to loop through bytes in the FIFO.

While at it do not test the return code from i2c_slave_event() for the
I2C_SLAVE_WRITE_RECEIVED since to my understanding this hardware cannot
generate NACK to incoming bytes and debug print itself does not have
much value.

Reported-by: Tian Ye <tianye@sugon.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
---
Hi Tian Ye. I've been testing the i2c-designware-slave.c recently and
discovered these write issues. Your recent patch gave an idea what might
cause them. In my solution I went testing DW_IC_STATUS_RFNE since
according to datasheet it's equivalent to RX_FULL interrupt in case
interrupts are masked. Seems to work here too.
Does this fix the issue you were seeing?
---
 drivers/i2c/busses/i2c-designware-core.h  |  1 +
 drivers/i2c/busses/i2c-designware-slave.c | 12 +++++++-----
 2 files changed, 8 insertions(+), 5 deletions(-)
diff mbox series

Patch

diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index dbf6bdc5f01b..6d1df28dd93b 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -108,6 +108,7 @@ 
 
 #define DW_IC_STATUS_ACTIVITY		BIT(0)
 #define DW_IC_STATUS_TFE		BIT(2)
+#define DW_IC_STATUS_RFNE		BIT(3)
 #define DW_IC_STATUS_MASTER_ACTIVITY	BIT(5)
 #define DW_IC_STATUS_SLAVE_ACTIVITY	BIT(6)
 
diff --git a/drivers/i2c/busses/i2c-designware-slave.c b/drivers/i2c/busses/i2c-designware-slave.c
index 1eac4f4d5573..295774a69b67 100644
--- a/drivers/i2c/busses/i2c-designware-slave.c
+++ b/drivers/i2c/busses/i2c-designware-slave.c
@@ -180,11 +180,13 @@  static int i2c_dw_irq_handler_slave(struct dw_i2c_dev *dev)
 					&val);
 		}
 
-		regmap_read(dev->map, DW_IC_DATA_CMD, &tmp);
-		val = tmp;
-		if (!i2c_slave_event(dev->slave, I2C_SLAVE_WRITE_RECEIVED,
-				     &val))
-			dev_vdbg(dev->dev, "Byte %X acked!", val);
+		do {
+			regmap_read(dev->map, DW_IC_DATA_CMD, &tmp);
+			val = tmp;
+			i2c_slave_event(dev->slave, I2C_SLAVE_WRITE_RECEIVED,
+					&val);
+			regmap_read(dev->map, DW_IC_STATUS, &tmp);
+		} while (tmp & DW_IC_STATUS_RFNE);
 	}
 
 	if (stat & DW_IC_INTR_RD_REQ) {