@@ -85,6 +85,49 @@
#define IWCR_HS_CNT2_SHIFT 10
#define IWCR_HS_CNT2_MASK (0x1F << IWCR_HS_CNT2_SHIFT)
+/* need a longer timeout if we're dealing with the fact we may well be
+ * looking at a multi-master environment
+ */
+#define DEF_TIMEOUT 32
+
+#define BUS_ERROR (-EREMOTEIO)
+#define XFER_NAKED (-ECONNREFUSED)
+#define I2C_RETRY (-2000) /* an error has occurred retry transmit */
+
+/* ICR initialize bit values
+ *
+ * 15 FM 0 (100 kHz operation)
+ * 14 UR 0 (No unit reset)
+ * 13 SADIE 0 (Disables the unit from interrupting on slave addresses
+ * matching its slave address)
+ * 12 ALDIE 0 (Disables the unit from interrupt when it loses arbitration
+ * in master mode)
+ * 11 SSDIE 0 (Disables interrupts from a slave stop detected, in slave mode)
+ * 10 BEIE 1 (Enable interrupts from detected bus errors, no ACK sent)
+ * 9 IRFIE 1 (Enable interrupts from full buffer received)
+ * 8 ITEIE 1 (Enables the I2C unit to interrupt when transmit buffer empty)
+ * 7 GCD 1 (Disables i2c unit response to general call messages as a slave)
+ * 6 IUE 0 (Disable unit until we change settings)
+ * 5 SCLE 1 (Enables the i2c clock output for master mode (drives SCL)
+ * 4 MA 0 (Only send stop with the ICR stop bit)
+ * 3 TB 0 (We are not transmitting a byte initially)
+ * 2 ACKNAK 0 (Send an ACK after the unit receives a byte)
+ * 1 STOP 0 (Do not send a STOP)
+ * 0 START 0 (Do not send a START)
+ */
+#define I2C_ICR_INIT (ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE)
+
+/* I2C status register init values
+ *
+ * 10 BED 1 (Clear bus error detected)
+ * 9 SAD 1 (Clear slave address detected)
+ * 7 IRF 1 (Clear IDBR Receive Full)
+ * 6 ITE 1 (Clear IDBR Transmit Empty)
+ * 5 ALD 1 (Clear Arbitration Loss Detected)
+ * 4 SSD 1 (Clear Slave Stop Detected)
+ */
+#define I2C_ISR_INIT 0x7FF /* status register init */
+
struct pxa_reg_layout {
u32 ibmr;
u32 idbr;
@@ -7,54 +7,6 @@
#ifndef _I2C_PXA_H_
#define _I2C_PXA_H_
-#if 0
-#define DEF_TIMEOUT 3
-#else
-/* need a longer timeout if we're dealing with the fact we may well be
- * looking at a multi-master environment
-*/
-#define DEF_TIMEOUT 32
-#endif
-
-#define BUS_ERROR (-EREMOTEIO)
-#define XFER_NAKED (-ECONNREFUSED)
-#define I2C_RETRY (-2000) /* an error has occurred retry transmit */
-
-/* ICR initialize bit values
-*
-* 15. FM 0 (100 Khz operation)
-* 14. UR 0 (No unit reset)
-* 13. SADIE 0 (Disables the unit from interrupting on slave addresses
-* matching its slave address)
-* 12. ALDIE 0 (Disables the unit from interrupt when it loses arbitration
-* in master mode)
-* 11. SSDIE 0 (Disables interrupts from a slave stop detected, in slave mode)
-* 10. BEIE 1 (Enable interrupts from detected bus errors, no ACK sent)
-* 9. IRFIE 1 (Enable interrupts from full buffer received)
-* 8. ITEIE 1 (Enables the I2C unit to interrupt when transmit buffer empty)
-* 7. GCD 1 (Disables i2c unit response to general call messages as a slave)
-* 6. IUE 0 (Disable unit until we change settings)
-* 5. SCLE 1 (Enables the i2c clock output for master mode (drives SCL)
-* 4. MA 0 (Only send stop with the ICR stop bit)
-* 3. TB 0 (We are not transmitting a byte initially)
-* 2. ACKNAK 0 (Send an ACK after the unit receives a byte)
-* 1. STOP 0 (Do not send a STOP)
-* 0. START 0 (Do not send a START)
-*
-*/
-#define I2C_ICR_INIT (ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE)
-
-/* I2C status register init values
- *
- * 10. BED 1 (Clear bus error detected)
- * 9. SAD 1 (Clear slave address detected)
- * 7. IRF 1 (Clear IDBR Receive Full)
- * 6. ITE 1 (Clear IDBR Transmit Empty)
- * 5. ALD 1 (Clear Arbitration Loss Detected)
- * 4. SSD 1 (Clear Slave Stop Detected)
- */
-#define I2C_ISR_INIT 0x7FF /* status register init */
-
struct i2c_pxa_platform_data {
unsigned int class;
unsigned int use_pio :1;
Move driver-private definitions out of the i2c-pxa.h platform data header file into the driver itself. Nothing outside of the driver makes use of these constants. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> --- drivers/i2c/busses/i2c-pxa.c | 43 ++++++++++++++++++++++++ include/linux/platform_data/i2c-pxa.h | 48 --------------------------- 2 files changed, 43 insertions(+), 48 deletions(-)