new file mode 100644
@@ -0,0 +1,170 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX System Controller Firmware (SCFW)
+
+maintainers:
+ - Dong Aisheng <aisheng.dong@nxp.com>
+
+description: System Controller Device Node
+ The System Controller Firmware (SCFW) is a low-level system function
+ which runs on a dedicated Cortex-M core to provide power, clock, and
+ resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
+ (QM, QP), and i.MX8QX (QXP, DX).
+ The AP communicates with the SC using a multi-ported MU module found
+ in the LSIO subsystem. The current definition of this MU module provides
+ 5 remote AP connections to the SC to support up to 5 execution environments
+ (TZ, HV, standard Linux, etc.). The SC side of this MU module interfaces
+ with the LSIO DSC IP bus. The SC firmware will communicate with this MU
+ using the MSI bus.
+
+properties:
+ $nodename:
+ const: 'scu'
+
+ compatible:
+ const: fsl,imx-scu
+
+ clock-controller:
+ description: |
+ $ref: /schemas/clock/fsl,scu-clk.yaml
+ Clock controller node that provides the clocks controlled by the SCU
+
+ imx8qx-ocotp:
+ description: |
+ $ref: /schemas/nvmem/fsl,scu-ocotp.yaml
+ OCOTP controller node provided by the SCU
+
+ keys:
+ description: |
+ $ref: /schemas/input/fsl,scu-key.yaml
+ Keys provided by the SCU
+
+ mboxes:
+ description: |
+ $ref: /schemas/mailbox/fsl,mu.yaml
+ List of phandle of 4 MU channels for tx, 4 MU channels for
+ rx, and 1 optional MU channel for general interrupt.
+ All MU channels must be in the same MU instance.
+ Cross instances are not allowed. The MU instance can only
+ be one of LSIO MU0~M4 for imx8qxp and imx8qm. Users need
+ to make sure use the one which is not conflict with other
+ execution environments. e.g. ATF.
+ minItems: 1
+ maxItems: 10
+
+ mbox-names:
+ description:
+ include "gip3" if want to support general MU interrupt.
+ minItems: 1
+ maxItems: 10
+
+ pinctrl:
+ description: |
+ $ref: /schemas/pinctrl/fsl,scu-pinctrl.yaml
+ Pin controller provided by the SCU
+
+ power-controller:
+ description: |
+ $ref: /schemas/power/fsl,scu-pd.yaml
+ Power domains controller node that provides the power domains
+ controlled by the SCU
+
+ rtc:
+ description: |
+ $ref: /schemas/rtc/fsl,scu-rtc.yaml
+ RTC controller provided by the SCU
+
+ thermal-sensor:
+ description: |
+ $ref: /schemas/thermal/fsl,scu-thermal.yaml
+ Thermal sensor provided by the SCU
+
+ watchdog:
+ description: |
+ $ref: /schemas/watchdog/fsl,scu-wdt.yaml
+ Watchdog controller provided by the SCU
+
+required:
+ - compatible
+ - mbox-names
+ - mboxes
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/firmware/imx/rsrc.h>
+ #include <dt-bindings/input/input.h>
+ #include <dt-bindings/pinctrl/pads-imx8qxp.h>
+
+ firmware {
+ scu {
+ compatible = "fsl,imx-scu";
+ mbox-names = "tx0", "tx1", "tx2", "tx3",
+ "rx0", "rx1", "rx2", "rx3",
+ "gip3";
+ mboxes = <&lsio_mu1 0 0
+ &lsio_mu1 0 1
+ &lsio_mu1 0 2
+ &lsio_mu1 0 3
+ &lsio_mu1 1 0
+ &lsio_mu1 1 1
+ &lsio_mu1 1 2
+ &lsio_mu1 1 3
+ &lsio_mu1 3 3>;
+
+ clock-controller {
+ compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
+ #clock-cells = <2>;
+ };
+
+ pinctrl {
+ compatible = "fsl,imx8qxp-iomuxc";
+
+ pinctrl_lpuart0: lpuart0grp {
+ fsl,pins = <
+ IMX8QXP_UART0_RX_ADMA_UART0_RX 0x06000020
+ IMX8QXP_UART0_TX_ADMA_UART0_TX 0x06000020
+ >;
+ };
+ };
+
+ imx8qx-ocotp {
+ compatible = "fsl,imx8qxp-scu-ocotp";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ fec_mac0: mac@2c4 {
+ reg = <0x2c4 6>;
+ };
+ };
+
+ power-controller {
+ compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd";
+ #power-domain-cells = <1>;
+ };
+
+ rtc {
+ compatible = "fsl,imx8qxp-sc-rtc";
+ };
+
+ keys {
+ compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key";
+ linux,keycodes = <KEY_POWER>;
+ };
+
+ watchdog {
+ compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt";
+ timeout-sec = <60>;
+ };
+
+ thermal-sensor {
+ compatible = "fsl,imx8qxp-sc-thermal", "fsl,imx-sc-thermal";
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };