diff mbox series

[v4,1/3] dt-bindings: media: Add bindings for THine THP7312 ISP

Message ID 20231017132103.9914-2-laurent.pinchart@ideasonboard.com
State Superseded
Headers show
Series media: i2c: Add driver for THine THP7312 ISP | expand

Commit Message

Laurent Pinchart Oct. 17, 2023, 1:21 p.m. UTC
From: Paul Elder <paul.elder@ideasonboard.com>

The THP7312 is an external ISP from THine. Add DT bindings for it.

Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
Changes since v2:

- Drop description of reg property
- Improve thine,boot-mode property documentation
- Making thine,boot-mode property optional
- Don't use underscores in supplies names
---
 .../bindings/media/i2c/thine,thp7312.yaml     | 226 ++++++++++++++++++
 MAINTAINERS                                   |   7 +
 2 files changed, 233 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml

Comments

Krzysztof Kozlowski Oct. 18, 2023, 3:02 p.m. UTC | #1
On 17/10/2023 15:21, Laurent Pinchart wrote:
> From: Paul Elder <paul.elder@ideasonboard.com>
> 
> The THP7312 is an external ISP from THine. Add DT bindings for it.
> 
> Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
> Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> ---
> Changes since v2:
> 

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof
Sakari Ailus Oct. 27, 2023, 11:55 a.m. UTC | #2
Hi Laurent,

Thank you for the patchset any my apologies for not reviewing it earlier.

On Tue, Oct 17, 2023 at 04:21:01PM +0300, Laurent Pinchart wrote:
> From: Paul Elder <paul.elder@ideasonboard.com>
> 
> The THP7312 is an external ISP from THine. Add DT bindings for it.
> 
> Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
> Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> ---
> Changes since v2:
> 
> - Drop description of reg property
> - Improve thine,boot-mode property documentation
> - Making thine,boot-mode property optional
> - Don't use underscores in supplies names
> ---
>  .../bindings/media/i2c/thine,thp7312.yaml     | 226 ++++++++++++++++++
>  MAINTAINERS                                   |   7 +
>  2 files changed, 233 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
> new file mode 100644
> index 000000000000..0758d8d44826
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
> @@ -0,0 +1,226 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (c) 2023 Ideas on Board
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/thine,thp7312.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: THine THP7312
> +
> +maintainers:
> +  - Paul Elder <paul.elder@@ideasonboard.com>
> +
> +description:
> +  The THP7312 is a standalone ISP controlled over i2c, and is capable of
> +  various image processing and correction functions, including 3A control. It
> +  can be connected to CMOS image sensors from various vendors, supporting both
> +  MIPI CSI-2 and parallel interfaces. It can also output on either MIPI CSI-2
> +  or parallel. The hardware is capable of transmitting and receiving MIPI
> +  interlaved data strams with data types or multiple virtual channel
> +  identifiers.
> +
> +allOf:
> +  - $ref: ../video-interface-devices.yaml#
> +
> +properties:
> +  compatible:
> +    const: thine,thp7312
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +    description: CLKI clock input
> +
> +  thine,boot-mode:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    minimum: 0
> +    maximum: 1
> +    default: 1
> +    description:
> +      Boot mode of the THP7312, reflecting the value of the BOOT[0] pin strap.
> +      0 is for the SPI/2-wire slave boot, 1 is for the SPI master boot (from
> +      external flash ROM).
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description:
> +      Reference to the GPIO connected to the RESET_N pin, if any.
> +      Must be released (set high) after all supplies are applied.
> +
> +  vddcore-supply:
> +    description:
> +      1.2V supply for core, PLL, MIPI rx and MIPI tx.
> +
> +  vhtermrx-supply:
> +    description:
> +      Supply for input (RX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel.
> +
> +  vddtx-supply:
> +    description:
> +      Supply for output (TX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel.
> +
> +  vddhost-supply:
> +    description:
> +      Supply for host interface. 1.8V, 2.8V, or 3.3V.
> +
> +  vddcmos-supply:
> +    description:
> +      Supply for sensor interface. 1.8V, 2.8V, or 3.3V.
> +
> +  vddgpio-0-supply:
> +    description:
> +      Supply for GPIO_0. 1.8V, 2.8V, or 3.3V.
> +
> +  vddgpio-1-supply:
> +    description:
> +      Supply for GPIO_1. 1.8V, 2.8V, or 3.3V.
> +
> +  orientation: true
> +  rotation: true
> +
> +  port:
> +    $ref: /schemas/graph.yaml#/$defs/port-base
> +    additionalProperties: false
> +
> +    properties:
> +      endpoint:
> +        $ref: /schemas/media/video-interfaces.yaml#
> +        unevaluatedProperties: false
> +
> +        properties:
> +          data-lanes:
> +            description:
> +              This property is for lane reordering between the THP7312 and the
> +              SoC. The sensor supports either two-lane, or four-lane operation.
> +              If this property is omitted four-lane operation is assumed. For
> +              two-lane operation the property must be set to <1 2>.

How are link frequencies determined by the device?

The description above also says the parallel interface is supported. The
bindings do not reflect that however.

Same for the sensor node below.

Is the intention to add support for these later on? In that case you'll
need bus-type and default that to CSI-2 for DTs conforming to these
bindings.

> +            minItems: 2
> +            maxItems: 4
> +            items:
> +              maximum: 4
> +
> +  sensors:
> +    type: object
> +    description: List of connected sensors
> +
> +    properties:
> +      "#address-cells":
> +        const: 1
> +
> +      "#size-cells":
> +        const: 0
> +
> +    patternProperties:
> +      "^sensor@[01]":
> +        type: object
> +        description:
> +          Sensors connected to the first and second input, with one node per
> +          sensor.
> +
> +        properties:
> +          thine,model:
> +            $ref: /schemas/types.yaml#/definitions/string
> +            description:
> +              Model of the connected sensors. Must be a valid compatible string.
> +
> +          reg:
> +            maxItems: 1
> +            description: THP7312 input port number
> +
> +          data-lanes:
> +            $ref: /schemas/media/video-interfaces.yaml#/properties/data-lanes
> +            items:
> +              maxItems: 4
> +            description:
> +              This property is for lane reordering between the THP7312 and the imaging
> +              sensor that it is connected to.
> +
> +        patternProperties:
> +          ".*-supply":
> +            description: Power supplies for the sensor
> +
> +        required:
> +          - reg
> +          - data-lanes
> +
> +        additionalProperties: false
> +
> +    required:
> +      - "#address-cells"
> +      - "#size-cells"
> +
> +    additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - reset-gpios
> +  - clocks
> +  - vddcore-supply
> +  - vhtermrx-supply
> +  - vddtx-supply
> +  - vddhost-supply
> +  - vddcmos-supply
> +  - vddgpio-0-supply
> +  - vddgpio-1-supply
> +  - sensors
> +  - port
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        camera@61 {
> +            compatible = "thine,thp7312";
> +            reg = <0x61>;
> +
> +            pinctrl-names = "default";
> +            pinctrl-0 = <&cam1_pins_default>;
> +
> +            reset-gpios = <&pio 119 GPIO_ACTIVE_LOW>;
> +            clocks = <&camera61_clk>;
> +
> +            vddcore-supply = <&vsys_v4p2>;
> +            vhtermrx-supply = <&vsys_v4p2>;
> +            vddtx-supply = <&vsys_v4p2>;
> +            vddhost-supply = <&vsys_v4p2>;
> +            vddcmos-supply = <&vsys_v4p2>;
> +            vddgpio-0-supply = <&vsys_v4p2>;
> +            vddgpio-1-supply = <&vsys_v4p2>;
> +
> +            orientation = <0>;
> +            rotation = <0>;
> +
> +            sensors {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                sensor@0 {
> +                    thine,model = "sony,imx258";
> +                    reg = <0>;
> +
> +                    data-lanes = <4 1 3 2>;

Does the device support lane mapping?

> +
> +                    dovdd-supply = <&vsys_v4p2>;
> +                    avdd-supply = <&vsys_v4p2>;
> +                    dvdd-supply = <&vsys_v4p2>;
> +                };
> +            };
> +
> +            port {
> +                thp7312_2_endpoint: endpoint {
> +                    remote-endpoint = <&mipi_thp7312_2>;
> +                    data-lanes = <4 2 1 3>;
> +                };
> +            };
> +    	  };
> +    };
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3b47e0b56859..7451367e6780 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -21448,6 +21448,13 @@ S:	Maintained
>  F:	Documentation/ABI/testing/sysfs-class-firmware-attributes
>  F:	drivers/platform/x86/think-lmi.?
>  
> +THP7312 ISP DRIVER
> +M:	Paul Elder <paul.elder@ideasonboard.com>
> +L:	linux-media@vger.kernel.org
> +S:	Maintained
> +T:	git git://linuxtv.org/media_tree.git
> +F:	Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
> +
>  THUNDERBOLT DMA TRAFFIC TEST DRIVER
>  M:	Isaac Hazan <isaac.hazan@intel.com>
>  L:	linux-usb@vger.kernel.org
Laurent Pinchart Oct. 27, 2023, 12:19 p.m. UTC | #3
Hi Sakari,

On Fri, Oct 27, 2023 at 11:55:52AM +0000, Sakari Ailus wrote:
> Hi Laurent,
> 
> Thank you for the patchset any my apologies for not reviewing it earlier.

No worries. Thank you for reviewing it now :-)

> On Tue, Oct 17, 2023 at 04:21:01PM +0300, Laurent Pinchart wrote:
> > From: Paul Elder <paul.elder@ideasonboard.com>
> > 
> > The THP7312 is an external ISP from THine. Add DT bindings for it.
> > 
> > Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
> > Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > ---
> > Changes since v2:
> > 
> > - Drop description of reg property
> > - Improve thine,boot-mode property documentation
> > - Making thine,boot-mode property optional
> > - Don't use underscores in supplies names
> > ---
> >  .../bindings/media/i2c/thine,thp7312.yaml     | 226 ++++++++++++++++++
> >  MAINTAINERS                                   |   7 +
> >  2 files changed, 233 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
> > new file mode 100644
> > index 000000000000..0758d8d44826
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
> > @@ -0,0 +1,226 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +# Copyright (c) 2023 Ideas on Board
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/i2c/thine,thp7312.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: THine THP7312
> > +
> > +maintainers:
> > +  - Paul Elder <paul.elder@@ideasonboard.com>
> > +
> > +description:
> > +  The THP7312 is a standalone ISP controlled over i2c, and is capable of
> > +  various image processing and correction functions, including 3A control. It
> > +  can be connected to CMOS image sensors from various vendors, supporting both
> > +  MIPI CSI-2 and parallel interfaces. It can also output on either MIPI CSI-2
> > +  or parallel. The hardware is capable of transmitting and receiving MIPI
> > +  interlaved data strams with data types or multiple virtual channel
> > +  identifiers.
> > +
> > +allOf:
> > +  - $ref: ../video-interface-devices.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    const: thine,thp7312
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  clocks:
> > +    maxItems: 1
> > +    description: CLKI clock input
> > +
> > +  thine,boot-mode:
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    minimum: 0
> > +    maximum: 1
> > +    default: 1
> > +    description:
> > +      Boot mode of the THP7312, reflecting the value of the BOOT[0] pin strap.
> > +      0 is for the SPI/2-wire slave boot, 1 is for the SPI master boot (from
> > +      external flash ROM).
> > +
> > +  reset-gpios:
> > +    maxItems: 1
> > +    description:
> > +      Reference to the GPIO connected to the RESET_N pin, if any.
> > +      Must be released (set high) after all supplies are applied.
> > +
> > +  vddcore-supply:
> > +    description:
> > +      1.2V supply for core, PLL, MIPI rx and MIPI tx.
> > +
> > +  vhtermrx-supply:
> > +    description:
> > +      Supply for input (RX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel.
> > +
> > +  vddtx-supply:
> > +    description:
> > +      Supply for output (TX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel.
> > +
> > +  vddhost-supply:
> > +    description:
> > +      Supply for host interface. 1.8V, 2.8V, or 3.3V.
> > +
> > +  vddcmos-supply:
> > +    description:
> > +      Supply for sensor interface. 1.8V, 2.8V, or 3.3V.
> > +
> > +  vddgpio-0-supply:
> > +    description:
> > +      Supply for GPIO_0. 1.8V, 2.8V, or 3.3V.
> > +
> > +  vddgpio-1-supply:
> > +    description:
> > +      Supply for GPIO_1. 1.8V, 2.8V, or 3.3V.
> > +
> > +  orientation: true
> > +  rotation: true
> > +
> > +  port:
> > +    $ref: /schemas/graph.yaml#/$defs/port-base
> > +    additionalProperties: false
> > +
> > +    properties:
> > +      endpoint:
> > +        $ref: /schemas/media/video-interfaces.yaml#
> > +        unevaluatedProperties: false
> > +
> > +        properties:
> > +          data-lanes:
> > +            description:
> > +              This property is for lane reordering between the THP7312 and the
> > +              SoC. The sensor supports either two-lane, or four-lane operation.
> > +              If this property is omitted four-lane operation is assumed. For
> > +              two-lane operation the property must be set to <1 2>.
> 
> How are link frequencies determined by the device?

The link frequency is not under direct control of the host. There are
registers to select between mode presets, each of them producing a
particular link frequency.

> The description above also says the parallel interface is supported. The
> bindings do not reflect that however.
> 
> Same for the sensor node below.
> 
> Is the intention to add support for these later on? In that case you'll
> need bus-type and default that to CSI-2 for DTs conforming to these
> bindings.

While documentation claims that parallel interfaces are supported, we
haven't been able to test this at all, due to lack of a suitable
hardware test platform. The intention is indeed to add support for them
later. I will add the bus-type property here.

> > +            minItems: 2
> > +            maxItems: 4
> > +            items:
> > +              maximum: 4
> > +
> > +  sensors:
> > +    type: object
> > +    description: List of connected sensors
> > +
> > +    properties:
> > +      "#address-cells":
> > +        const: 1
> > +
> > +      "#size-cells":
> > +        const: 0
> > +
> > +    patternProperties:
> > +      "^sensor@[01]":
> > +        type: object
> > +        description:
> > +          Sensors connected to the first and second input, with one node per
> > +          sensor.
> > +
> > +        properties:
> > +          thine,model:
> > +            $ref: /schemas/types.yaml#/definitions/string
> > +            description:
> > +              Model of the connected sensors. Must be a valid compatible string.
> > +
> > +          reg:
> > +            maxItems: 1
> > +            description: THP7312 input port number
> > +
> > +          data-lanes:
> > +            $ref: /schemas/media/video-interfaces.yaml#/properties/data-lanes
> > +            items:
> > +              maxItems: 4
> > +            description:
> > +              This property is for lane reordering between the THP7312 and the imaging
> > +              sensor that it is connected to.
> > +
> > +        patternProperties:
> > +          ".*-supply":
> > +            description: Power supplies for the sensor
> > +
> > +        required:
> > +          - reg
> > +          - data-lanes
> > +
> > +        additionalProperties: false
> > +
> > +    required:
> > +      - "#address-cells"
> > +      - "#size-cells"
> > +
> > +    additionalProperties: false
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - reset-gpios
> > +  - clocks
> > +  - vddcore-supply
> > +  - vhtermrx-supply
> > +  - vddtx-supply
> > +  - vddhost-supply
> > +  - vddcmos-supply
> > +  - vddgpio-0-supply
> > +  - vddgpio-1-supply
> > +  - sensors
> > +  - port
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/gpio/gpio.h>
> > +
> > +    i2c {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        camera@61 {
> > +            compatible = "thine,thp7312";
> > +            reg = <0x61>;
> > +
> > +            pinctrl-names = "default";
> > +            pinctrl-0 = <&cam1_pins_default>;
> > +
> > +            reset-gpios = <&pio 119 GPIO_ACTIVE_LOW>;
> > +            clocks = <&camera61_clk>;
> > +
> > +            vddcore-supply = <&vsys_v4p2>;
> > +            vhtermrx-supply = <&vsys_v4p2>;
> > +            vddtx-supply = <&vsys_v4p2>;
> > +            vddhost-supply = <&vsys_v4p2>;
> > +            vddcmos-supply = <&vsys_v4p2>;
> > +            vddgpio-0-supply = <&vsys_v4p2>;
> > +            vddgpio-1-supply = <&vsys_v4p2>;
> > +
> > +            orientation = <0>;
> > +            rotation = <0>;
> > +
> > +            sensors {
> > +                #address-cells = <1>;
> > +                #size-cells = <0>;
> > +
> > +                sensor@0 {
> > +                    thine,model = "sony,imx258";
> > +                    reg = <0>;
> > +
> > +                    data-lanes = <4 1 3 2>;
> 
> Does the device support lane mapping?

Yes it does, both on the input and output.

> > +
> > +                    dovdd-supply = <&vsys_v4p2>;
> > +                    avdd-supply = <&vsys_v4p2>;
> > +                    dvdd-supply = <&vsys_v4p2>;
> > +                };
> > +            };
> > +
> > +            port {
> > +                thp7312_2_endpoint: endpoint {
> > +                    remote-endpoint = <&mipi_thp7312_2>;
> > +                    data-lanes = <4 2 1 3>;
> > +                };
> > +            };
> > +    	  };
> > +    };
> > +...
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 3b47e0b56859..7451367e6780 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -21448,6 +21448,13 @@ S:	Maintained
> >  F:	Documentation/ABI/testing/sysfs-class-firmware-attributes
> >  F:	drivers/platform/x86/think-lmi.?
> >  
> > +THP7312 ISP DRIVER
> > +M:	Paul Elder <paul.elder@ideasonboard.com>
> > +L:	linux-media@vger.kernel.org
> > +S:	Maintained
> > +T:	git git://linuxtv.org/media_tree.git
> > +F:	Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
> > +
> >  THUNDERBOLT DMA TRAFFIC TEST DRIVER
> >  M:	Isaac Hazan <isaac.hazan@intel.com>
> >  L:	linux-usb@vger.kernel.org
Laurent Pinchart Oct. 28, 2023, 3:21 p.m. UTC | #4
On Fri, Oct 27, 2023 at 04:27:21PM +0000, Sakari Ailus wrote:
> On Fri, Oct 27, 2023 at 06:36:49PM +0300, Laurent Pinchart wrote:
> > On Fri, Oct 27, 2023 at 02:52:38PM +0000, Sakari Ailus wrote:
> > > On Fri, Oct 27, 2023 at 03:46:34PM +0300, Laurent Pinchart wrote:
> > > > > > > > +  port:
> > > > > > > > +    $ref: /schemas/graph.yaml#/$defs/port-base
> > > > > > > > +    additionalProperties: false
> > > > > > > > +
> > > > > > > > +    properties:
> > > > > > > > +      endpoint:
> > > > > > > > +        $ref: /schemas/media/video-interfaces.yaml#
> > > > > > > > +        unevaluatedProperties: false
> > > > > > > > +
> > > > > > > > +        properties:
> > > > > > > > +          data-lanes:
> > > > > > > > +            description:
> > > > > > > > +              This property is for lane reordering between the THP7312 and the
> > > > > > > > +              SoC. The sensor supports either two-lane, or four-lane operation.
> > > > > > > > +              If this property is omitted four-lane operation is assumed. For
> > > > > > > > +              two-lane operation the property must be set to <1 2>.
> > > > > > > 
> > > > > > > How are link frequencies determined by the device?
> > > > > > 
> > > > > > The link frequency is not under direct control of the host. There are
> > > > > > registers to select between mode presets, each of them producing a
> > > > > > particular link frequency.
> > > > > 
> > > > > If they are known, one could only allow setting the modes with known-good
> > > > > link requencies. This could be added later on, too, affecting systems with
> > > > > link-frequencies set. I guess you could also add it now, as optional.
> > > > 
> > > > I vote for later :-)
> > > > 
> > > > > Where's the link frequency information available? In documentation or in
> > > > > on the firmware API?
> > > > 
> > > > In the documentation (which is not public I'm afraid).
> > > 
> > > Could you add this information in the driver?
> > > 
> > > Co-incidentally, the driver is lacking the LINK_FREQ control. It should be
> > > added.
> > 
> > Oops. Seems I got caught red-handed. I'll fix that (and add the
> > PIXEL_RATE control too).
> 
> :-)
> 
> The PIXEL_RATE is intended to be the pixel rate on the pixel array. The
> driver doesn't have HBLANK or VBLANK so is it even useful to have
> PIXEL_RATE?

I don't mind leaving it out, it's easier.
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
new file mode 100644
index 000000000000..0758d8d44826
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
@@ -0,0 +1,226 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2023 Ideas on Board
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/thine,thp7312.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: THine THP7312
+
+maintainers:
+  - Paul Elder <paul.elder@@ideasonboard.com>
+
+description:
+  The THP7312 is a standalone ISP controlled over i2c, and is capable of
+  various image processing and correction functions, including 3A control. It
+  can be connected to CMOS image sensors from various vendors, supporting both
+  MIPI CSI-2 and parallel interfaces. It can also output on either MIPI CSI-2
+  or parallel. The hardware is capable of transmitting and receiving MIPI
+  interlaved data strams with data types or multiple virtual channel
+  identifiers.
+
+allOf:
+  - $ref: ../video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: thine,thp7312
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+    description: CLKI clock input
+
+  thine,boot-mode:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 1
+    default: 1
+    description:
+      Boot mode of the THP7312, reflecting the value of the BOOT[0] pin strap.
+      0 is for the SPI/2-wire slave boot, 1 is for the SPI master boot (from
+      external flash ROM).
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      Reference to the GPIO connected to the RESET_N pin, if any.
+      Must be released (set high) after all supplies are applied.
+
+  vddcore-supply:
+    description:
+      1.2V supply for core, PLL, MIPI rx and MIPI tx.
+
+  vhtermrx-supply:
+    description:
+      Supply for input (RX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel.
+
+  vddtx-supply:
+    description:
+      Supply for output (TX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel.
+
+  vddhost-supply:
+    description:
+      Supply for host interface. 1.8V, 2.8V, or 3.3V.
+
+  vddcmos-supply:
+    description:
+      Supply for sensor interface. 1.8V, 2.8V, or 3.3V.
+
+  vddgpio-0-supply:
+    description:
+      Supply for GPIO_0. 1.8V, 2.8V, or 3.3V.
+
+  vddgpio-1-supply:
+    description:
+      Supply for GPIO_1. 1.8V, 2.8V, or 3.3V.
+
+  orientation: true
+  rotation: true
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            description:
+              This property is for lane reordering between the THP7312 and the
+              SoC. The sensor supports either two-lane, or four-lane operation.
+              If this property is omitted four-lane operation is assumed. For
+              two-lane operation the property must be set to <1 2>.
+            minItems: 2
+            maxItems: 4
+            items:
+              maximum: 4
+
+  sensors:
+    type: object
+    description: List of connected sensors
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+    patternProperties:
+      "^sensor@[01]":
+        type: object
+        description:
+          Sensors connected to the first and second input, with one node per
+          sensor.
+
+        properties:
+          thine,model:
+            $ref: /schemas/types.yaml#/definitions/string
+            description:
+              Model of the connected sensors. Must be a valid compatible string.
+
+          reg:
+            maxItems: 1
+            description: THP7312 input port number
+
+          data-lanes:
+            $ref: /schemas/media/video-interfaces.yaml#/properties/data-lanes
+            items:
+              maxItems: 4
+            description:
+              This property is for lane reordering between the THP7312 and the imaging
+              sensor that it is connected to.
+
+        patternProperties:
+          ".*-supply":
+            description: Power supplies for the sensor
+
+        required:
+          - reg
+          - data-lanes
+
+        additionalProperties: false
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - reset-gpios
+  - clocks
+  - vddcore-supply
+  - vhtermrx-supply
+  - vddtx-supply
+  - vddhost-supply
+  - vddcmos-supply
+  - vddgpio-0-supply
+  - vddgpio-1-supply
+  - sensors
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@61 {
+            compatible = "thine,thp7312";
+            reg = <0x61>;
+
+            pinctrl-names = "default";
+            pinctrl-0 = <&cam1_pins_default>;
+
+            reset-gpios = <&pio 119 GPIO_ACTIVE_LOW>;
+            clocks = <&camera61_clk>;
+
+            vddcore-supply = <&vsys_v4p2>;
+            vhtermrx-supply = <&vsys_v4p2>;
+            vddtx-supply = <&vsys_v4p2>;
+            vddhost-supply = <&vsys_v4p2>;
+            vddcmos-supply = <&vsys_v4p2>;
+            vddgpio-0-supply = <&vsys_v4p2>;
+            vddgpio-1-supply = <&vsys_v4p2>;
+
+            orientation = <0>;
+            rotation = <0>;
+
+            sensors {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                sensor@0 {
+                    thine,model = "sony,imx258";
+                    reg = <0>;
+
+                    data-lanes = <4 1 3 2>;
+
+                    dovdd-supply = <&vsys_v4p2>;
+                    avdd-supply = <&vsys_v4p2>;
+                    dvdd-supply = <&vsys_v4p2>;
+                };
+            };
+
+            port {
+                thp7312_2_endpoint: endpoint {
+                    remote-endpoint = <&mipi_thp7312_2>;
+                    data-lanes = <4 2 1 3>;
+                };
+            };
+    	  };
+    };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 3b47e0b56859..7451367e6780 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -21448,6 +21448,13 @@  S:	Maintained
 F:	Documentation/ABI/testing/sysfs-class-firmware-attributes
 F:	drivers/platform/x86/think-lmi.?
 
+THP7312 ISP DRIVER
+M:	Paul Elder <paul.elder@ideasonboard.com>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+T:	git git://linuxtv.org/media_tree.git
+F:	Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml
+
 THUNDERBOLT DMA TRAFFIC TEST DRIVER
 M:	Isaac Hazan <isaac.hazan@intel.com>
 L:	linux-usb@vger.kernel.org