@@ -98,6 +98,86 @@ void sdhci_uhs2_reset(struct sdhci_host *host, u16 mask)
}
EXPORT_SYMBOL_GPL(sdhci_uhs2_reset);
+void sdhci_uhs2_set_power(struct sdhci_host *host, unsigned char mode,
+ unsigned short vdd)
+{
+ struct mmc_host *mmc = host->mmc;
+ u8 pwr;
+
+ /* FIXME: check if flags & MMC_UHS2_SUPPORT? */
+ if (!(host->mmc->caps & MMC_CAP_UHS2)) {
+ sdhci_set_power(host, mode, vdd);
+ return;
+ }
+
+ if (mode != MMC_POWER_OFF) {
+ pwr = sdhci_get_vdd_value(vdd);
+ if (!pwr)
+ WARN(1, "%s: Invalid vdd %#x\n",
+ mmc_hostname(host->mmc), vdd);
+
+ pwr |= SDHCI_VDD2_POWER_180;
+ }
+
+ if (host->pwr == pwr)
+ return;
+ host ->pwr = pwr;
+
+ if (pwr == 0) {
+ sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
+
+ if (!IS_ERR(host->mmc->supply.vmmc))
+ mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
+ if (!IS_ERR_OR_NULL(host->mmc->supply.vmmc2))
+ mmc_regulator_set_ocr(mmc, mmc->supply.vmmc2, 0);
+
+ if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
+ sdhci_runtime_pm_bus_off(host);
+ } else {
+ if (!IS_ERR(host->mmc->supply.vmmc))
+ mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
+ if (!IS_ERR_OR_NULL(host->mmc->supply.vmmc2))
+ /* support 1.8v only for now */
+ mmc_regulator_set_ocr(mmc, mmc->supply.vmmc2,
+ fls(MMC_VDD2_165_195) - 1);
+
+ /*
+ * Spec says that we should clear the power reg before setting
+ * a new value. Some controllers don't seem to like this though.
+ */
+ if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
+ sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
+
+ /*
+ * At least the Marvell CaFe chip gets confused if we set the
+ * voltage and set turn on power at the same time, so set the
+ * voltage first.
+ */
+ if (host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)
+ sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
+
+ /* vdd first */
+ pwr |= SDHCI_POWER_ON;
+ sdhci_writeb(host, pwr & 0xf, SDHCI_POWER_CONTROL);
+ mdelay(5);
+
+ pwr |= SDHCI_VDD2_POWER_ON;
+ sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
+ mdelay(5);
+
+ if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
+ sdhci_runtime_pm_bus_on(host);
+
+ /*
+ * Some controllers need an extra 10ms delay of 10ms before
+ * they can apply clock after applying power
+ */
+ if (host->quirks & SDHCI_QUIRK_DELAY_AFTER_POWER)
+ mdelay(10);
+ }
+}
+EXPORT_SYMBOL_GPL(sdhci_uhs2_set_power);
+
/*****************************************************************************\
* *
* Driver init/exit *
@@ -211,5 +211,7 @@ struct sdhci_host;
void sdhci_uhs2_dump_regs(struct sdhci_host *host);
void sdhci_uhs2_reset(struct sdhci_host *host, u16 mask);
+void sdhci_uhs2_set_power(struct sdhci_host *host, unsigned char mode,
+ unsigned short vdd);
#endif /* __SDHCI_UHS2_H */
@@ -186,13 +186,14 @@ static void sdhci_disable_card_detection(struct sdhci_host *host)
sdhci_set_card_detection(host, false);
}
-static void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
+void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
{
if (host->bus_on)
return;
host->bus_on = true;
pm_runtime_get_noresume(mmc_dev(host->mmc));
}
+EXPORT_SYMBOL_GPL(sdhci_runtime_pm_bus_on);
void sdhci_runtime_pm_bus_off(struct sdhci_host *host)
{
@@ -2018,36 +2019,47 @@ static void sdhci_set_power_reg(struct sdhci_host *host, unsigned char mode,
sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
}
+unsigned short sdhci_get_vdd_value(unsigned short vdd)
+{
+ u8 pwr;
+
+ switch (1 << vdd) {
+ case MMC_VDD_165_195:
+ /*
+ * Without a regulator, SDHCI does not support 2.0v
+ * so we only get here if the driver deliberately
+ * added the 2.0v range to ocr_avail. Map it to 1.8v
+ * for the purpose of turning on the power.
+ */
+ case MMC_VDD_20_21:
+ pwr = SDHCI_POWER_180;
+ break;
+ case MMC_VDD_29_30:
+ case MMC_VDD_30_31:
+ pwr = SDHCI_POWER_300;
+ break;
+ case MMC_VDD_32_33:
+ case MMC_VDD_33_34:
+ pwr = SDHCI_POWER_330;
+ break;
+ default:
+ pwr = 0;
+ }
+
+ return pwr;
+}
+EXPORT_SYMBOL_GPL(sdhci_get_vdd_value);
+
void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode,
unsigned short vdd)
{
u8 pwr = 0;
if (mode != MMC_POWER_OFF) {
- switch (1 << vdd) {
- case MMC_VDD_165_195:
- /*
- * Without a regulator, SDHCI does not support 2.0v
- * so we only get here if the driver deliberately
- * added the 2.0v range to ocr_avail. Map it to 1.8v
- * for the purpose of turning on the power.
- */
- case MMC_VDD_20_21:
- pwr = SDHCI_POWER_180;
- break;
- case MMC_VDD_29_30:
- case MMC_VDD_30_31:
- pwr = SDHCI_POWER_300;
- break;
- case MMC_VDD_32_33:
- case MMC_VDD_33_34:
- pwr = SDHCI_POWER_330;
- break;
- default:
+ pwr = sdhci_get_vdd_value(vdd);
+ if (!pwr)
WARN(1, "%s: Invalid vdd %#x\n",
mmc_hostname(host->mmc), vdd);
- break;
- }
}
if (host->pwr == pwr)
@@ -831,6 +831,7 @@ static inline void sdhci_read_caps(struct sdhci_host *host)
__sdhci_read_caps(host, NULL, NULL, NULL);
}
+void sdhci_runtime_pm_bus_on(struct sdhci_host *host);
void sdhci_runtime_pm_bus_off(struct sdhci_host *host);
u16 sdhci_calc_clk(struct sdhci_host *host, unsigned int clock,
unsigned int *actual_clock);
@@ -841,6 +842,7 @@ void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
void sdhci_set_power_and_bus_voltage(struct sdhci_host *host,
unsigned char mode,
unsigned short vdd);
+unsigned short sdhci_get_vdd_value(unsigned short vdd);
void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode,
unsigned short vdd);
void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq);