diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig
index fdd8bc08569e..3c3eedea35f7 100644
--- a/drivers/soc/mediatek/Kconfig
+++ b/drivers/soc/mediatek/Kconfig
@@ -73,4 +73,14 @@ config MTK_MMSYS
 	  Say yes here to add support for the MediaTek Multimedia
 	  Subsystem (MMSYS).
 
+config MTK_SVS
+	tristate "MediaTek Smart Voltage Scaling(SVS)"
+	depends on MTK_EFUSE && NVMEM
+	help
+	  The Smart Voltage Scaling(SVS) engine is a piece of hardware
+	  which has several controllers(banks) for calculating suitable
+	  voltage to different power domains(CPU/GPU/CCI) according to
+	  chip process corner, temperatures and other factors. Then DVFS
+	  driver could apply SVS bank voltage to PMIC/Buck.
+
 endmenu
diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile
index 90270f8114ed..0e9e703c931a 100644
--- a/drivers/soc/mediatek/Makefile
+++ b/drivers/soc/mediatek/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_MTK_SCPSYS) += mtk-scpsys.o
 obj-$(CONFIG_MTK_SCPSYS_PM_DOMAINS) += mtk-pm-domains.o
 obj-$(CONFIG_MTK_MMSYS) += mtk-mmsys.o
 obj-$(CONFIG_MTK_MMSYS) += mtk-mutex.o
+obj-$(CONFIG_MTK_SVS) += mtk-svs.o
diff --git a/drivers/soc/mediatek/mtk-svs.c b/drivers/soc/mediatek/mtk-svs.c
new file mode 100644
index 000000000000..2d7ea3d607c4
--- /dev/null
+++ b/drivers/soc/mediatek/mtk-svs.c
@@ -0,0 +1,1422 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/pm_opp.h>
+#include <linux/pm_qos.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+/* svs bank 1-line software id */
+#define SVSB_CPU_LITTLE			BIT(0)
+#define SVSB_CPU_BIG			BIT(1)
+#define SVSB_CCI			BIT(2)
+#define SVSB_GPU			BIT(3)
+
+/* svs bank mode support */
+#define SVSB_MODE_ALL_DISABLE		0
+#define SVSB_MODE_INIT01		BIT(1)
+#define SVSB_MODE_INIT02		BIT(2)
+
+/* svs bank volt flags */
+#define SVSB_INIT01_PD_REQ		BIT(0)
+#define SVSB_INIT01_VOLT_IGNORE		BIT(1)
+#define SVSB_INIT01_VOLT_INC_ONLY	BIT(2)
+
+/* svs bank register common configuration */
+#define SVSB_DET_MAX			0xffff
+#define SVSB_DET_WINDOW			0xa28
+#define SVSB_DTHI			0x1
+#define SVSB_DTLO			0xfe
+#define SVSB_EN_INIT01			0x1
+#define SVSB_EN_INIT02			0x5
+#define SVSB_EN_OFF			0x0
+#define SVSB_INTEN_INIT0x		0x00005f01
+#define SVSB_INTSTS_CLEAN		0x00ffffff
+#define SVSB_INTSTS_COMPLETE		0x1
+#define SVSB_RUNCONFIG_DEFAULT		0x80000000
+
+/* svs bank related setting */
+#define MAX_OPP_ENTRIES			16
+#define SVSB_DC_SIGNED_BIT		BIT(15)
+#define SVSB_DET_CLK_EN			BIT(31)
+
+static DEFINE_SPINLOCK(svs_lock);
+
+/**
+ * enum svsb_phase - svs bank phase enumeration
+ * @SVSB_PHASE_ERROR: svs bank encounters unexpected condition
+ * @SVSB_PHASE_INIT01: svs bank basic init for data calibration
+ * @SVSB_PHASE_INIT02: svs bank can provide voltages to opp table
+ * @SVSB_PHASE_MAX: total number of svs bank phase (debug purpose)
+ *
+ * Each svs bank has its own independent phase and we enable each svs bank by
+ * running their phase orderly. However, when svs bank encounters unexpected
+ * condition, it will fire an irq (PHASE_ERROR) to inform svs software.
+ *
+ * svs bank general phase-enabled order:
+ * SVSB_PHASE_INIT01 -> SVSB_PHASE_INIT02
+ */
+enum svsb_phase {
+	SVSB_PHASE_ERROR = 0,
+	SVSB_PHASE_INIT01,
+	SVSB_PHASE_INIT02,
+	SVSB_PHASE_MAX,
+};
+
+enum svs_reg_index {
+	DESCHAR = 0,
+	TEMPCHAR,
+	DETCHAR,
+	AGECHAR,
+	DCCONFIG,
+	AGECONFIG,
+	FREQPCT30,
+	FREQPCT74,
+	LIMITVALS,
+	VBOOT,
+	DETWINDOW,
+	CONFIG,
+	TSCALCS,
+	RUNCONFIG,
+	SVSEN,
+	INIT2VALS,
+	DCVALUES,
+	AGEVALUES,
+	VOP30,
+	VOP74,
+	TEMP,
+	INTSTS,
+	INTSTSRAW,
+	INTEN,
+	CHKINT,
+	CHKSHIFT,
+	STATUS,
+	VDESIGN30,
+	VDESIGN74,
+	DVT30,
+	DVT74,
+	AGECOUNT,
+	SMSTATE0,
+	SMSTATE1,
+	CTL0,
+	DESDETSEC,
+	TEMPAGESEC,
+	CTRLSPARE0,
+	CTRLSPARE1,
+	CTRLSPARE2,
+	CTRLSPARE3,
+	CORESEL,
+	THERMINTST,
+	INTST,
+	THSTAGE0ST,
+	THSTAGE1ST,
+	THSTAGE2ST,
+	THAHBST0,
+	THAHBST1,
+	SPARE0,
+	SPARE1,
+	SPARE2,
+	SPARE3,
+	THSLPEVEB,
+	SVS_REG_MAX,
+};
+
+static const u32 svs_regs_v2[] = {
+	[DESCHAR]		= 0xc00,
+	[TEMPCHAR]		= 0xc04,
+	[DETCHAR]		= 0xc08,
+	[AGECHAR]		= 0xc0c,
+	[DCCONFIG]		= 0xc10,
+	[AGECONFIG]		= 0xc14,
+	[FREQPCT30]		= 0xc18,
+	[FREQPCT74]		= 0xc1c,
+	[LIMITVALS]		= 0xc20,
+	[VBOOT]			= 0xc24,
+	[DETWINDOW]		= 0xc28,
+	[CONFIG]		= 0xc2c,
+	[TSCALCS]		= 0xc30,
+	[RUNCONFIG]		= 0xc34,
+	[SVSEN]			= 0xc38,
+	[INIT2VALS]		= 0xc3c,
+	[DCVALUES]		= 0xc40,
+	[AGEVALUES]		= 0xc44,
+	[VOP30]			= 0xc48,
+	[VOP74]			= 0xc4c,
+	[TEMP]			= 0xc50,
+	[INTSTS]		= 0xc54,
+	[INTSTSRAW]		= 0xc58,
+	[INTEN]			= 0xc5c,
+	[CHKINT]		= 0xc60,
+	[CHKSHIFT]		= 0xc64,
+	[STATUS]		= 0xc68,
+	[VDESIGN30]		= 0xc6c,
+	[VDESIGN74]		= 0xc70,
+	[DVT30]			= 0xc74,
+	[DVT74]			= 0xc78,
+	[AGECOUNT]		= 0xc7c,
+	[SMSTATE0]		= 0xc80,
+	[SMSTATE1]		= 0xc84,
+	[CTL0]			= 0xc88,
+	[DESDETSEC]		= 0xce0,
+	[TEMPAGESEC]		= 0xce4,
+	[CTRLSPARE0]		= 0xcf0,
+	[CTRLSPARE1]		= 0xcf4,
+	[CTRLSPARE2]		= 0xcf8,
+	[CTRLSPARE3]		= 0xcfc,
+	[CORESEL]		= 0xf00,
+	[THERMINTST]		= 0xf04,
+	[INTST]			= 0xf08,
+	[THSTAGE0ST]		= 0xf0c,
+	[THSTAGE1ST]		= 0xf10,
+	[THSTAGE2ST]		= 0xf14,
+	[THAHBST0]		= 0xf18,
+	[THAHBST1]		= 0xf1c,
+	[SPARE0]		= 0xf20,
+	[SPARE1]		= 0xf24,
+	[SPARE2]		= 0xf28,
+	[SPARE3]		= 0xf2c,
+	[THSLPEVEB]		= 0xf30,
+};
+
+/**
+ * struct svs_platform - svs platform control
+ * @name: svs platform name
+ * @base: svs platform register base
+ * @dev: svs platform device
+ * @main_clk: main clock for svs bank
+ * @pbank: svs bank pointer needing to be protected by spin_lock section
+ * @banks: svs banks that svs platform supports
+ * @efuse_parsing: svs platform efuse parsing function pointer
+ * @probe: svs platform probe function pointer
+ * @irqflags: svs platform irq settings flags
+ * @efuse_max: total number of svs efuse
+ * @regs: svs platform registers map
+ * @bank_max: total number of svs banks
+ * @efuse: svs efuse data received from NVMEM framework
+ */
+struct svs_platform {
+	char *name;
+	void __iomem *base;
+	struct device *dev;
+	struct clk *main_clk;
+	struct svs_bank *pbank;
+	struct svs_bank *banks;
+	bool (*efuse_parsing)(struct svs_platform *svsp);
+	int (*probe)(struct svs_platform *svsp);
+	unsigned long irqflags;
+	size_t efuse_max;
+	const u32 *regs;
+	u32 bank_max;
+	u32 *efuse;
+};
+
+struct svs_platform_data {
+	char *name;
+	struct svs_bank *banks;
+	bool (*efuse_parsing)(struct svs_platform *svsp);
+	int (*probe)(struct svs_platform *svsp);
+	unsigned long irqflags;
+	const u32 *regs;
+	u32 bank_max;
+};
+
+/**
+ * struct svs_bank - svs bank representation
+ * @dev: bank device
+ * @opp_dev: device for opp table/buck control
+ * @pd_dev: power domain device for SoC mtcmos control
+ * @init_completion: the timeout completion for bank init
+ * @buck: regulator used by opp_dev
+ * @lock: mutex lock to protect voltage update process
+ * @set_freq_pct: function pointer to set bank frequency percent table
+ * @get_volts: function pointer to get bank voltages
+ * @name: bank name
+ * @buck_name: regulator name
+ * @phase: bank current phase
+ * @volt_od: bank voltage overdrive
+ * @pm_runtime_enabled_count: bank pm runtime enabled count
+ * @mode_support: bank mode support.
+ * @freq_base: reference frequency for bank init
+ * @vboot: voltage request for bank init01 only
+ * @opp_dfreq: default opp frequency table
+ * @opp_dvolt: default opp voltage table
+ * @freq_pct: frequency percent table for bank init
+ * @volt: bank voltage table
+ * @volt_step: bank voltage step
+ * @volt_base: bank voltage base
+ * @volt_flags: bank voltage flags
+ * @vmax: bank voltage maximum
+ * @vmin: bank voltage minimum
+ * @age_config: bank age configuration
+ * @age_voffset_in: bank age voltage offset
+ * @dc_config: bank dc configuration
+ * @dc_voffset_in: bank dc voltage offset
+ * @dvt_fixed: bank dvt fixed value
+ * @vco: bank VCO value
+ * @chk_shift: bank chicken shift
+ * @core_sel: bank selection
+ * @opp_count: bank opp count
+ * @int_st: bank interrupt identification
+ * @sw_id: bank software identification
+ * @cpu_id: cpu core id for SVS CPU bank use only
+ * @ctl0: TS-x selection
+ * @bdes: svs efuse data
+ * @mdes: svs efuse data
+ * @mtdes: svs efuse data
+ * @dcbdet: svs efuse data
+ * @dcmdet: svs efuse data
+ *
+ * Svs bank will generate suitalbe voltages by below general math equation
+ * and provide these voltages to opp voltage table.
+ *
+ * opp_volt[i] = (volt[i] * volt_step) + volt_base;
+ */
+struct svs_bank {
+	struct device *dev;
+	struct device *opp_dev;
+	struct device *pd_dev;
+	struct completion init_completion;
+	struct regulator *buck;
+	struct mutex lock;	/* lock to protect voltage update process */
+	void (*set_freq_pct)(struct svs_platform *svsp);
+	void (*get_volts)(struct svs_platform *svsp);
+	char *name;
+	char *buck_name;
+	enum svsb_phase phase;
+	s32 volt_od;
+	u32 pm_runtime_enabled_count;
+	u32 mode_support;
+	u32 freq_base;
+	u32 vboot;
+	u32 opp_dfreq[MAX_OPP_ENTRIES];
+	u32 opp_dvolt[MAX_OPP_ENTRIES];
+	u32 freq_pct[MAX_OPP_ENTRIES];
+	u32 volt[MAX_OPP_ENTRIES];
+	u32 volt_step;
+	u32 volt_base;
+	u32 volt_flags;
+	u32 vmax;
+	u32 vmin;
+	u32 age_config;
+	u32 age_voffset_in;
+	u32 dc_config;
+	u32 dc_voffset_in;
+	u32 dvt_fixed;
+	u32 vco;
+	u32 chk_shift;
+	u32 core_sel;
+	u32 opp_count;
+	u32 int_st;
+	u32 sw_id;
+	u32 cpu_id;
+	u32 ctl0;
+	u32 bdes;
+	u32 mdes;
+	u32 mtdes;
+	u32 dcbdet;
+	u32 dcmdet;
+};
+
+static u32 percent(u32 numerator, u32 denominator)
+{
+	/* If not divide 1000, "numerator * 100" will have data overflow. */
+	numerator /= 1000;
+	denominator /= 1000;
+
+	return DIV_ROUND_UP(numerator * 100, denominator);
+}
+
+static u32 svs_readl_relaxed(struct svs_platform *svsp, enum svs_reg_index rg_i)
+{
+	return readl_relaxed(svsp->base + svsp->regs[rg_i]);
+}
+
+static void svs_writel_relaxed(struct svs_platform *svsp, u32 val,
+			       enum svs_reg_index rg_i)
+{
+	writel_relaxed(val, svsp->base + svsp->regs[rg_i]);
+}
+
+static void svs_switch_bank(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+
+	svs_writel_relaxed(svsp, svsb->core_sel, CORESEL);
+}
+
+static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step,
+				     u32 svsb_volt_base)
+{
+	return (svsb_volt * svsb_volt_step) + svsb_volt_base;
+}
+
+static int svs_adjust_pm_opp_volts(struct svs_bank *svsb)
+{
+	int ret = -EPERM;
+	u32 i, svsb_volt, opp_volt;
+
+	mutex_lock(&svsb->lock);
+
+	/* vmin <= svsb_volt (opp_volt) <= default opp voltage */
+	for (i = 0; i < svsb->opp_count; i++) {
+		switch (svsb->phase) {
+		case SVSB_PHASE_ERROR:
+			opp_volt = svsb->opp_dvolt[i];
+			break;
+		case SVSB_PHASE_INIT01:
+			/* do nothing */
+			goto unlock_mutex;
+		case SVSB_PHASE_INIT02:
+			svsb_volt = max(svsb->volt[i], svsb->vmin);
+			opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
+							     svsb->volt_step,
+							     svsb->volt_base);
+			break;
+		default:
+			dev_err(svsb->dev, "unknown phase: %u\n", svsb->phase);
+			ret = -EINVAL;
+			goto unlock_mutex;
+		}
+
+		opp_volt = min(opp_volt, svsb->opp_dvolt[i]);
+		ret = dev_pm_opp_adjust_voltage(svsb->opp_dev,
+						svsb->opp_dfreq[i],
+						opp_volt, opp_volt,
+						svsb->opp_dvolt[i]);
+		if (ret) {
+			dev_err(svsb->dev, "set %uuV fail: %d\n",
+				opp_volt, ret);
+			goto unlock_mutex;
+		}
+	}
+
+unlock_mutex:
+	mutex_unlock(&svsb->lock);
+
+	return ret;
+}
+
+static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
+{
+	u32 vx;
+
+	if (v0 == v1 || f0 == f1)
+		return v0;
+
+	/* *100 to have decimal fraction factor */
+	vx = (v0 * 100) - ((((v0 - v1) * 100) / (f0 - f1)) * (f0 - fx));
+
+	return DIV_ROUND_UP(vx, 100);
+}
+
+static void svs_get_bank_volts_v2(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+	u32 temp, i;
+
+	temp = svs_readl_relaxed(svsp, VOP74);
+	svsb->volt[14] = (temp >> 24) & GENMASK(7, 0);
+	svsb->volt[12] = (temp >> 16) & GENMASK(7, 0);
+	svsb->volt[10] = (temp >> 8)  & GENMASK(7, 0);
+	svsb->volt[8] = (temp & GENMASK(7, 0));
+
+	temp = svs_readl_relaxed(svsp, VOP30);
+	svsb->volt[6] = (temp >> 24) & GENMASK(7, 0);
+	svsb->volt[4] = (temp >> 16) & GENMASK(7, 0);
+	svsb->volt[2] = (temp >> 8)  & GENMASK(7, 0);
+	svsb->volt[0] = (temp & GENMASK(7, 0));
+
+	for (i = 0; i <= 12; i += 2)
+		svsb->volt[i + 1] = interpolate(svsb->freq_pct[i],
+						svsb->freq_pct[i + 2],
+						svsb->volt[i],
+						svsb->volt[i + 2],
+						svsb->freq_pct[i + 1]);
+
+	svsb->volt[15] = interpolate(svsb->freq_pct[12],
+				     svsb->freq_pct[14],
+				     svsb->volt[12],
+				     svsb->volt[14],
+				     svsb->freq_pct[15]);
+
+	for (i = 0; i < svsb->opp_count; i++)
+		svsb->volt[i] += svsb->volt_od;
+}
+
+static void svs_set_bank_freq_pct_v2(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+
+	svs_writel_relaxed(svsp,
+			   (svsb->freq_pct[14] << 24) |
+			   (svsb->freq_pct[12] << 16) |
+			   (svsb->freq_pct[10] << 8) |
+			   svsb->freq_pct[8],
+			   FREQPCT74);
+
+	svs_writel_relaxed(svsp,
+			   (svsb->freq_pct[6] << 24) |
+			   (svsb->freq_pct[4] << 16) |
+			   (svsb->freq_pct[2] << 8) |
+			   svsb->freq_pct[0],
+			   FREQPCT30);
+}
+
+static void svs_set_bank_phase(struct svs_platform *svsp,
+			       enum svsb_phase target_phase)
+{
+	struct svs_bank *svsb = svsp->pbank;
+	u32 des_char, temp_char, det_char, limit_vals, init2vals;
+
+	svs_switch_bank(svsp);
+
+	des_char = (svsb->bdes << 8) | svsb->mdes;
+	svs_writel_relaxed(svsp, des_char, DESCHAR);
+
+	temp_char = (svsb->vco << 16) | (svsb->mtdes << 8) | svsb->dvt_fixed;
+	svs_writel_relaxed(svsp, temp_char, TEMPCHAR);
+
+	det_char = (svsb->dcbdet << 8) | svsb->dcmdet;
+	svs_writel_relaxed(svsp, det_char, DETCHAR);
+
+	svs_writel_relaxed(svsp, svsb->dc_config, DCCONFIG);
+	svs_writel_relaxed(svsp, svsb->age_config, AGECONFIG);
+	svs_writel_relaxed(svsp, SVSB_RUNCONFIG_DEFAULT, RUNCONFIG);
+
+	svsb->set_freq_pct(svsp);
+
+	limit_vals = (svsb->vmax << 24) | (svsb->vmin << 16) |
+		     (SVSB_DTHI << 8) | SVSB_DTLO;
+	svs_writel_relaxed(svsp, limit_vals, LIMITVALS);
+
+	svs_writel_relaxed(svsp, SVSB_DET_WINDOW, DETWINDOW);
+	svs_writel_relaxed(svsp, SVSB_DET_MAX, CONFIG);
+	svs_writel_relaxed(svsp, svsb->chk_shift, CHKSHIFT);
+	svs_writel_relaxed(svsp, svsb->ctl0, CTL0);
+	svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
+
+	switch (target_phase) {
+	case SVSB_PHASE_INIT01:
+		svs_writel_relaxed(svsp, svsb->vboot, VBOOT);
+		svs_writel_relaxed(svsp, SVSB_INTEN_INIT0x, INTEN);
+		svs_writel_relaxed(svsp, SVSB_EN_INIT01, SVSEN);
+		break;
+	case SVSB_PHASE_INIT02:
+		svs_writel_relaxed(svsp, SVSB_INTEN_INIT0x, INTEN);
+		init2vals = (svsb->age_voffset_in << 16) | svsb->dc_voffset_in;
+		svs_writel_relaxed(svsp, init2vals, INIT2VALS);
+		svs_writel_relaxed(svsp, SVSB_EN_INIT02, SVSEN);
+		break;
+	default:
+		dev_err(svsb->dev, "requested unknown target phase: %u\n",
+			target_phase);
+		break;
+	}
+}
+
+static inline void svs_error_isr_handler(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+
+	dev_err(svsb->dev, "%s: CORESEL = 0x%08x\n",
+		__func__, svs_readl_relaxed(svsp, CORESEL));
+	dev_err(svsb->dev, "SVSEN = 0x%08x, INTSTS = 0x%08x\n",
+		svs_readl_relaxed(svsp, SVSEN),
+		svs_readl_relaxed(svsp, INTSTS));
+	dev_err(svsb->dev, "SMSTATE0 = 0x%08x, SMSTATE1 = 0x%08x\n",
+		svs_readl_relaxed(svsp, SMSTATE0),
+		svs_readl_relaxed(svsp, SMSTATE1));
+
+	svsb->phase = SVSB_PHASE_ERROR;
+	svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+	svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
+}
+
+static inline void svs_init01_isr_handler(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+
+	dev_info(svsb->dev, "%s: VDN74~30:0x%08x~0x%08x, DC:0x%08x\n",
+		 __func__, svs_readl_relaxed(svsp, VDESIGN74),
+		 svs_readl_relaxed(svsp, VDESIGN30),
+		 svs_readl_relaxed(svsp, DCVALUES));
+
+	svsb->phase = SVSB_PHASE_INIT01;
+	svsb->dc_voffset_in = ~(svs_readl_relaxed(svsp, DCVALUES) &
+				GENMASK(15, 0)) + 1;
+	if (svsb->volt_flags & SVSB_INIT01_VOLT_IGNORE ||
+	    (svsb->dc_voffset_in & SVSB_DC_SIGNED_BIT &&
+	     svsb->volt_flags & SVSB_INIT01_VOLT_INC_ONLY))
+		svsb->dc_voffset_in = 0;
+
+	svsb->age_voffset_in = svs_readl_relaxed(svsp, AGEVALUES) &
+			       GENMASK(15, 0);
+
+	svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+	svs_writel_relaxed(svsp, SVSB_INTSTS_COMPLETE, INTSTS);
+	svsb->core_sel &= ~SVSB_DET_CLK_EN;
+}
+
+static inline void svs_init02_isr_handler(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+
+	dev_info(svsb->dev, "%s: VOP74~30:0x%08x~0x%08x, DC:0x%08x\n",
+		 __func__, svs_readl_relaxed(svsp, VOP74),
+		 svs_readl_relaxed(svsp, VOP30),
+		 svs_readl_relaxed(svsp, DCVALUES));
+
+	svsb->phase = SVSB_PHASE_INIT02;
+	svsb->get_volts(svsp);
+
+	svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+	svs_writel_relaxed(svsp, SVSB_INTSTS_COMPLETE, INTSTS);
+}
+
+static irqreturn_t svs_isr(int irq, void *data)
+{
+	struct svs_platform *svsp = data;
+	struct svs_bank *svsb = NULL;
+	unsigned long flags;
+	u32 idx, int_sts, svs_en;
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+		WARN(!svsb, "%s: svsb(%s) is null", __func__, svsb->name);
+
+		spin_lock_irqsave(&svs_lock, flags);
+		svsp->pbank = svsb;
+
+		/* Find out which svs bank fires interrupt */
+		if (svsb->int_st & svs_readl_relaxed(svsp, INTST)) {
+			spin_unlock_irqrestore(&svs_lock, flags);
+			continue;
+		}
+
+		svs_switch_bank(svsp);
+		int_sts = svs_readl_relaxed(svsp, INTSTS);
+		svs_en = svs_readl_relaxed(svsp, SVSEN);
+
+		if (int_sts == SVSB_INTSTS_COMPLETE &&
+		    svs_en == SVSB_EN_INIT01)
+			svs_init01_isr_handler(svsp);
+		else if (int_sts == SVSB_INTSTS_COMPLETE &&
+			 svs_en == SVSB_EN_INIT02)
+			svs_init02_isr_handler(svsp);
+		else
+			svs_error_isr_handler(svsp);
+
+		spin_unlock_irqrestore(&svs_lock, flags);
+		break;
+	}
+
+	svs_adjust_pm_opp_volts(svsb);
+
+	if (svsb->phase == SVSB_PHASE_INIT01 ||
+	    svsb->phase == SVSB_PHASE_INIT02)
+		complete(&svsb->init_completion);
+
+	return IRQ_HANDLED;
+}
+
+static int svs_init01(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	struct pm_qos_request *cpu_qos_request;
+	unsigned long flags, time_left;
+	bool search_done;
+	int ret = 0, r;
+	u32 opp_freq, opp_vboot, buck_volt, idx, i;
+
+	cpu_qos_request = kzalloc(sizeof(*cpu_qos_request), GFP_KERNEL);
+	if (!cpu_qos_request)
+		return -ENOMEM;
+
+	/* Let CPUs leave idle-off state for initializing svs_init01. */
+	cpu_latency_qos_add_request(cpu_qos_request, 0);
+
+	 /* Svs bank init01 preparation - power enable */
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (!(svsb->mode_support & SVSB_MODE_INIT01))
+			continue;
+
+		ret = regulator_enable(svsb->buck);
+		if (ret) {
+			dev_err(svsb->dev, "%s enable fail: %d\n",
+				svsb->buck_name, ret);
+			goto init01_remove_cpu_qos_request;
+		}
+
+		/* Some buck doesn't support mode change. Show fail msg only */
+		ret = regulator_set_mode(svsb->buck, REGULATOR_MODE_FAST);
+		if (ret)
+			dev_notice(svsb->dev, "set fast mode fail: %d\n", ret);
+
+		if (svsb->volt_flags & SVSB_INIT01_PD_REQ) {
+			if (!pm_runtime_enabled(svsb->pd_dev)) {
+				pm_runtime_enable(svsb->pd_dev);
+				svsb->pm_runtime_enabled_count++;
+			}
+
+			ret = pm_runtime_get_sync(svsb->pd_dev);
+			if (ret < 0) {
+				dev_err(svsb->dev, "mtcmos on fail: %d\n", ret);
+				goto init01_remove_cpu_qos_request;
+			}
+		}
+	}
+
+	/*
+	 * Svs bank init01 preparation - vboot voltage adjustment
+	 * Sometimes two svs banks use the same buck. Therefore,
+	 * we have to set each svs bank to target voltage(vboot) first.
+	 */
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (!(svsb->mode_support & SVSB_MODE_INIT01))
+			continue;
+
+		/*
+		 * Find the fastest freq that can be run at vboot and
+		 * fix to that freq until svs_init01 is done.
+		 */
+		search_done = false;
+		opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot,
+						      svsb->volt_step,
+						      svsb->volt_base);
+
+		for (i = 0; i < svsb->opp_count; i++) {
+			opp_freq = svsb->opp_dfreq[i];
+			if (!search_done && svsb->opp_dvolt[i] <= opp_vboot) {
+				ret = dev_pm_opp_adjust_voltage(svsb->opp_dev,
+								opp_freq,
+								opp_vboot,
+								opp_vboot,
+								opp_vboot);
+				if (ret) {
+					dev_err(svsb->dev,
+						"set opp %uuV vboot fail: %d\n",
+						opp_vboot, ret);
+					goto init01_finish;
+				}
+
+				search_done = true;
+			} else {
+				ret = dev_pm_opp_disable(svsb->opp_dev,
+							 svsb->opp_dfreq[i]);
+				if (ret) {
+					dev_err(svsb->dev,
+						"opp %uHz disable fail: %d\n",
+						svsb->opp_dfreq[i], ret);
+					goto init01_finish;
+				}
+			}
+		}
+	}
+
+	/* Svs bank init01 begins */
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (!(svsb->mode_support & SVSB_MODE_INIT01))
+			continue;
+
+		opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot,
+						      svsb->volt_step,
+						      svsb->volt_base);
+
+		buck_volt = regulator_get_voltage(svsb->buck);
+		if (buck_volt != opp_vboot) {
+			dev_err(svsb->dev,
+				"buck voltage: %uuV, expected vboot: %uuV\n",
+				buck_volt, opp_vboot);
+			ret = -EPERM;
+			goto init01_finish;
+		}
+
+		spin_lock_irqsave(&svs_lock, flags);
+		svsp->pbank = svsb;
+		svs_set_bank_phase(svsp, SVSB_PHASE_INIT01);
+		spin_unlock_irqrestore(&svs_lock, flags);
+
+		time_left = wait_for_completion_timeout(&svsb->init_completion,
+							msecs_to_jiffies(5000));
+		if (!time_left) {
+			dev_err(svsb->dev, "init01 completion timeout\n");
+			ret = -EBUSY;
+			goto init01_finish;
+		}
+	}
+
+init01_finish:
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (!(svsb->mode_support & SVSB_MODE_INIT01))
+			continue;
+
+		for (i = 0; i < svsb->opp_count; i++) {
+			r = dev_pm_opp_enable(svsb->opp_dev,
+					      svsb->opp_dfreq[i]);
+			if (r)
+				dev_err(svsb->dev, "opp %uHz enable fail: %d\n",
+					svsb->opp_dfreq[i], r);
+		}
+
+		if (svsb->volt_flags & SVSB_INIT01_PD_REQ) {
+			r = pm_runtime_put_sync(svsb->pd_dev);
+			if (r)
+				dev_err(svsb->dev, "mtcmos off fail: %d\n", r);
+
+			if (svsb->pm_runtime_enabled_count > 0) {
+				pm_runtime_disable(svsb->pd_dev);
+				svsb->pm_runtime_enabled_count--;
+			}
+		}
+
+		r = regulator_set_mode(svsb->buck, REGULATOR_MODE_NORMAL);
+		if (r)
+			dev_notice(svsb->dev, "set normal mode fail: %d\n", r);
+
+		r = regulator_disable(svsb->buck);
+		if (r)
+			dev_err(svsb->dev, "%s disable fail: %d\n",
+				svsb->buck_name, r);
+	}
+
+init01_remove_cpu_qos_request:
+	cpu_latency_qos_remove_request(cpu_qos_request);
+	kfree(cpu_qos_request);
+
+	return ret;
+}
+
+static int svs_init02(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	unsigned long flags, time_left;
+	u32 idx;
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (!(svsb->mode_support & SVSB_MODE_INIT02))
+			continue;
+
+		reinit_completion(&svsb->init_completion);
+		spin_lock_irqsave(&svs_lock, flags);
+		svsp->pbank = svsb;
+		svs_set_bank_phase(svsp, SVSB_PHASE_INIT02);
+		spin_unlock_irqrestore(&svs_lock, flags);
+
+		time_left = wait_for_completion_timeout(&svsb->init_completion,
+							msecs_to_jiffies(5000));
+		if (!time_left) {
+			dev_err(svsb->dev, "init02 completion timeout\n");
+			return -EBUSY;
+		}
+	}
+
+	return 0;
+}
+
+static int svs_start(struct svs_platform *svsp)
+{
+	int ret;
+
+	ret = svs_init01(svsp);
+	if (ret)
+		return ret;
+
+	ret = svs_init02(svsp);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int svs_suspend(struct device *dev)
+{
+	struct svs_platform *svsp = dev_get_drvdata(dev);
+	struct svs_bank *svsb;
+	unsigned long flags;
+	u32 idx;
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		/* This might wait for svs_isr() process */
+		spin_lock_irqsave(&svs_lock, flags);
+		svsp->pbank = svsb;
+		svs_switch_bank(svsp);
+		svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+		svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
+		spin_unlock_irqrestore(&svs_lock, flags);
+
+		svsb->phase = SVSB_PHASE_ERROR;
+		svs_adjust_pm_opp_volts(svsb);
+	}
+
+	clk_disable_unprepare(svsp->main_clk);
+
+	return 0;
+}
+
+static int svs_resume(struct device *dev)
+{
+	struct svs_platform *svsp = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_prepare_enable(svsp->main_clk);
+	if (ret) {
+		dev_err(svsp->dev, "cannot enable main_clk, disable svs\n");
+		return ret;
+	}
+
+	ret = svs_init02(svsp);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int svs_bank_resource_setup(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	struct dev_pm_opp *opp;
+	unsigned long freq;
+	int count, ret;
+	u32 idx, i;
+
+	dev_set_drvdata(svsp->dev, svsp);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		switch (svsb->sw_id) {
+		case SVSB_CPU_LITTLE:
+			svsb->name = "SVSB_CPU_LITTLE";
+			break;
+		case SVSB_CPU_BIG:
+			svsb->name = "SVSB_CPU_BIG";
+			break;
+		case SVSB_CCI:
+			svsb->name = "SVSB_CCI";
+			break;
+		case SVSB_GPU:
+			svsb->name = "SVSB_GPU";
+			break;
+		default:
+			dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
+			return -EINVAL;
+		}
+
+		svsb->dev = devm_kzalloc(svsp->dev, sizeof(*svsb->dev),
+					 GFP_KERNEL);
+		if (!svsb->dev)
+			return -ENOMEM;
+
+		ret = dev_set_name(svsb->dev, "%s", svsb->name);
+		if (ret)
+			return ret;
+
+		dev_set_drvdata(svsb->dev, svsp);
+
+		ret = dev_pm_opp_of_add_table(svsb->opp_dev);
+		if (ret) {
+			dev_err(svsb->dev, "add opp table fail: %d\n", ret);
+			return ret;
+		}
+
+		mutex_init(&svsb->lock);
+		init_completion(&svsb->init_completion);
+
+		if (svsb->mode_support & SVSB_MODE_INIT01) {
+			svsb->buck = devm_regulator_get_optional(svsb->opp_dev,
+								 svsb->buck_name);
+			if (IS_ERR(svsb->buck)) {
+				dev_err(svsb->dev, "cannot get \"%s-supply\"\n",
+					svsb->buck_name);
+				return PTR_ERR(svsb->buck);
+			}
+		}
+
+		count = dev_pm_opp_get_opp_count(svsb->opp_dev);
+		if (svsb->opp_count != count) {
+			dev_err(svsb->dev,
+				"opp_count not \"%u\" but get \"%d\"?\n",
+				svsb->opp_count, count);
+			return count;
+		}
+
+		for (i = 0, freq = U32_MAX; i < svsb->opp_count; i++, freq--) {
+			opp = dev_pm_opp_find_freq_floor(svsb->opp_dev, &freq);
+			if (IS_ERR(opp)) {
+				dev_err(svsb->dev, "cannot find freq = %ld\n",
+					PTR_ERR(opp));
+				return PTR_ERR(opp);
+			}
+
+			svsb->opp_dfreq[i] = freq;
+			svsb->opp_dvolt[i] = dev_pm_opp_get_voltage(opp);
+			svsb->freq_pct[i] = percent(svsb->opp_dfreq[i],
+						    svsb->freq_base);
+			dev_pm_opp_put(opp);
+		}
+	}
+
+	return 0;
+}
+
+static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	u32 idx, i, ft_pgm;
+
+	for (i = 0; i < svsp->efuse_max; i++)
+		if (svsp->efuse[i])
+			dev_info(svsp->dev, "M_HW_RES%d: 0x%08x\n",
+				 i, svsp->efuse[i]);
+
+	if (!svsp->efuse[2]) {
+		dev_notice(svsp->dev, "svs_efuse[2] = 0x0?\n");
+		return false;
+	}
+
+	/* Svs efuse parsing */
+	ft_pgm = (svsp->efuse[0] >> 4) & GENMASK(3, 0);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (ft_pgm <= 1)
+			svsb->volt_flags |= SVSB_INIT01_VOLT_IGNORE;
+
+		switch (svsb->sw_id) {
+		case SVSB_CPU_LITTLE:
+			svsb->bdes = svsp->efuse[16] & GENMASK(7, 0);
+			svsb->mdes = (svsp->efuse[16] >> 8) & GENMASK(7, 0);
+			svsb->dcbdet = (svsp->efuse[16] >> 16) & GENMASK(7, 0);
+			svsb->dcmdet = (svsp->efuse[16] >> 24) & GENMASK(7, 0);
+			svsb->mtdes  = (svsp->efuse[17] >> 16) & GENMASK(7, 0);
+
+			if (ft_pgm <= 3)
+				svsb->volt_od += 10;
+			else
+				svsb->volt_od += 2;
+			break;
+		case SVSB_CPU_BIG:
+			svsb->bdes = svsp->efuse[18] & GENMASK(7, 0);
+			svsb->mdes = (svsp->efuse[18] >> 8) & GENMASK(7, 0);
+			svsb->dcbdet = (svsp->efuse[18] >> 16) & GENMASK(7, 0);
+			svsb->dcmdet = (svsp->efuse[18] >> 24) & GENMASK(7, 0);
+			svsb->mtdes  = svsp->efuse[17] & GENMASK(7, 0);
+
+			if (ft_pgm <= 3)
+				svsb->volt_od += 15;
+			else
+				svsb->volt_od += 12;
+			break;
+		case SVSB_CCI:
+			svsb->bdes = svsp->efuse[4] & GENMASK(7, 0);
+			svsb->mdes = (svsp->efuse[4] >> 8) & GENMASK(7, 0);
+			svsb->dcbdet = (svsp->efuse[4] >> 16) & GENMASK(7, 0);
+			svsb->dcmdet = (svsp->efuse[4] >> 24) & GENMASK(7, 0);
+			svsb->mtdes  = (svsp->efuse[5] >> 16) & GENMASK(7, 0);
+
+			if (ft_pgm <= 3)
+				svsb->volt_od += 10;
+			else
+				svsb->volt_od += 2;
+			break;
+		case SVSB_GPU:
+			svsb->bdes = svsp->efuse[6] & GENMASK(7, 0);
+			svsb->mdes = (svsp->efuse[6] >> 8) & GENMASK(7, 0);
+			svsb->dcbdet = (svsp->efuse[6] >> 16) & GENMASK(7, 0);
+			svsb->dcmdet = (svsp->efuse[6] >> 24) & GENMASK(7, 0);
+			svsb->mtdes  = svsp->efuse[5] & GENMASK(7, 0);
+
+			if (ft_pgm >= 2) {
+				svsb->freq_base = 800000000; /* 800MHz */
+				svsb->dvt_fixed = 2;
+			}
+			break;
+		default:
+			dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
+			return false;
+		}
+	}
+
+	return true;
+}
+
+static bool svs_is_efuse_data_correct(struct svs_platform *svsp)
+{
+	struct nvmem_cell *cell;
+
+	/* Get svs efuse by nvmem */
+	cell = nvmem_cell_get(svsp->dev, "svs-calibration-data");
+	if (IS_ERR(cell)) {
+		dev_err(svsp->dev, "no \"svs-calibration-data\"? %ld\n",
+			PTR_ERR(cell));
+		return false;
+	}
+
+	svsp->efuse = nvmem_cell_read(cell, &svsp->efuse_max);
+	if (IS_ERR(svsp->efuse)) {
+		dev_err(svsp->dev, "cannot read svs efuse: %ld\n",
+			PTR_ERR(svsp->efuse));
+		return false;
+	}
+
+	svsp->efuse_max /= sizeof(u32);
+	nvmem_cell_put(cell);
+
+	return svsp->efuse_parsing(svsp);
+}
+
+static struct device *svs_get_subsys_device(struct svs_platform *svsp,
+					    const char *node_name)
+{
+	struct platform_device *pdev;
+	struct device_node *np;
+
+	np = of_find_node_by_name(NULL, node_name);
+	if (!np) {
+		dev_err(svsp->dev, "cannot find %s node\n", node_name);
+		return ERR_PTR(-ENODEV);
+	}
+
+	pdev = of_find_device_by_node(np);
+	if (!pdev) {
+		of_node_put(np);
+		dev_err(svsp->dev, "cannot find pdev by %s\n", node_name);
+		return ERR_PTR(-ENXIO);
+	}
+
+	of_node_put(np);
+
+	return &pdev->dev;
+}
+
+static struct device *svs_add_device_link(struct svs_platform *svsp,
+					  const char *node_name)
+{
+	struct device *dev;
+	struct device_link *sup_link;
+
+	if (!node_name) {
+		dev_err(svsp->dev, "node name cannot be null\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	dev = svs_get_subsys_device(svsp, node_name);
+	if (IS_ERR(dev))
+		return dev;
+
+	sup_link = device_link_add(svsp->dev, dev,
+				   DL_FLAG_AUTOREMOVE_CONSUMER);
+	if (!sup_link) {
+		dev_err(svsp->dev, "sup_link is NULL\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	if (sup_link->supplier->links.status != DL_DEV_DRIVER_BOUND)
+		return ERR_PTR(-EPROBE_DEFER);
+
+	return dev;
+}
+
+static int svs_mt8183_platform_probe(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	u32 idx;
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		switch (svsb->sw_id) {
+		case SVSB_CPU_LITTLE:
+		case SVSB_CPU_BIG:
+			svsb->opp_dev = get_cpu_device(svsb->cpu_id);
+			break;
+		case SVSB_CCI:
+			svsb->opp_dev = svs_add_device_link(svsp, "cci");
+			break;
+		case SVSB_GPU:
+			svsb->opp_dev = svs_add_device_link(svsp, "mali");
+			svsb->pd_dev = svs_add_device_link(svsp, "mali_gpu_core2");
+			if (IS_ERR(svsb->pd_dev))
+				return PTR_ERR(svsb->pd_dev);
+			break;
+		default:
+			dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
+			return -EINVAL;
+		}
+
+		if (IS_ERR(svsb->opp_dev))
+			return PTR_ERR(svsb->opp_dev);
+	}
+
+	return 0;
+}
+
+static struct svs_bank svs_mt8183_banks[] = {
+	{
+		.sw_id			= SVSB_CPU_LITTLE,
+		.set_freq_pct		= svs_set_bank_freq_pct_v2,
+		.get_volts		= svs_get_bank_volts_v2,
+		.cpu_id			= 0,
+		.buck_name		= "proc",
+		.volt_flags		= SVSB_INIT01_VOLT_INC_ONLY,
+		.mode_support		= SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+		.opp_count		= MAX_OPP_ENTRIES,
+		.freq_base		= 1989000000,
+		.vboot			= 0x30,
+		.volt_step		= 6250,
+		.volt_base		= 500000,
+		.vmax			= 0x64,
+		.vmin			= 0x18,
+		.age_config		= 0x555555,
+		.dc_config		= 0x555555,
+		.dvt_fixed		= 0x7,
+		.vco			= 0x10,
+		.chk_shift		= 0x77,
+		.core_sel		= 0x8fff0000,
+		.int_st			= BIT(0),
+		.ctl0			= 0x00010001,
+	},
+	{
+		.sw_id			= SVSB_CPU_BIG,
+		.set_freq_pct		= svs_set_bank_freq_pct_v2,
+		.get_volts		= svs_get_bank_volts_v2,
+		.cpu_id			= 4,
+		.buck_name		= "proc",
+		.volt_flags		= SVSB_INIT01_VOLT_INC_ONLY,
+		.mode_support		= SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+		.opp_count		= MAX_OPP_ENTRIES,
+		.freq_base		= 1989000000,
+		.vboot			= 0x30,
+		.volt_step		= 6250,
+		.volt_base		= 500000,
+		.vmax			= 0x58,
+		.vmin			= 0x10,
+		.age_config		= 0x555555,
+		.dc_config		= 0x555555,
+		.dvt_fixed		= 0x7,
+		.vco			= 0x10,
+		.chk_shift		= 0x77,
+		.core_sel		= 0x8fff0001,
+		.int_st			= BIT(1),
+		.ctl0			= 0x00000001,
+	},
+	{
+		.sw_id			= SVSB_CCI,
+		.set_freq_pct		= svs_set_bank_freq_pct_v2,
+		.get_volts		= svs_get_bank_volts_v2,
+		.buck_name		= "proc",
+		.volt_flags		= SVSB_INIT01_VOLT_INC_ONLY,
+		.mode_support		= SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+		.opp_count		= MAX_OPP_ENTRIES,
+		.freq_base		= 1196000000,
+		.vboot			= 0x30,
+		.volt_step		= 6250,
+		.volt_base		= 500000,
+		.vmax			= 0x64,
+		.vmin			= 0x18,
+		.age_config		= 0x555555,
+		.dc_config		= 0x555555,
+		.dvt_fixed		= 0x7,
+		.vco			= 0x10,
+		.chk_shift		= 0x77,
+		.core_sel		= 0x8fff0002,
+		.int_st			= BIT(2),
+		.ctl0			= 0x00100003,
+	},
+	{
+		.sw_id			= SVSB_GPU,
+		.set_freq_pct		= svs_set_bank_freq_pct_v2,
+		.get_volts		= svs_get_bank_volts_v2,
+		.buck_name		= "mali",
+		.volt_flags		= SVSB_INIT01_PD_REQ |
+					  SVSB_INIT01_VOLT_INC_ONLY,
+		.mode_support		= SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+		.opp_count		= MAX_OPP_ENTRIES,
+		.freq_base		= 900000000,
+		.vboot			= 0x30,
+		.volt_step		= 6250,
+		.volt_base		= 500000,
+		.vmax			= 0x40,
+		.vmin			= 0x14,
+		.age_config		= 0x555555,
+		.dc_config		= 0x555555,
+		.dvt_fixed		= 0x3,
+		.vco			= 0x10,
+		.chk_shift		= 0x77,
+		.core_sel		= 0x8fff0003,
+		.int_st			= BIT(3),
+		.ctl0			= 0x00050001,
+	},
+};
+
+static const struct svs_platform_data svs_mt8183_platform_data = {
+	.name = "mt8183-svs",
+	.banks = svs_mt8183_banks,
+	.efuse_parsing = svs_mt8183_efuse_parsing,
+	.probe = svs_mt8183_platform_probe,
+	.irqflags = IRQF_TRIGGER_LOW,
+	.regs = svs_regs_v2,
+	.bank_max = ARRAY_SIZE(svs_mt8183_banks),
+};
+
+static const struct of_device_id svs_of_match[] = {
+	{
+		.compatible = "mediatek,mt8183-svs",
+		.data = &svs_mt8183_platform_data,
+	}, {
+		/* Sentinel */
+	},
+};
+
+static struct svs_platform *svs_platform_probe(struct platform_device *pdev)
+{
+	struct svs_platform *svsp;
+	const struct svs_platform_data *svsp_data;
+	int ret;
+
+	svsp_data = of_device_get_match_data(&pdev->dev);
+	if (!svsp_data) {
+		dev_err(&pdev->dev, "no svs platform data?\n");
+		return ERR_PTR(-EPERM);
+	}
+
+	svsp = devm_kzalloc(&pdev->dev, sizeof(*svsp), GFP_KERNEL);
+	if (!svsp)
+		return ERR_PTR(-ENOMEM);
+
+	svsp->dev = &pdev->dev;
+	svsp->name = svsp_data->name;
+	svsp->banks = svsp_data->banks;
+	svsp->efuse_parsing = svsp_data->efuse_parsing;
+	svsp->probe = svsp_data->probe;
+	svsp->irqflags = svsp_data->irqflags;
+	svsp->regs = svsp_data->regs;
+	svsp->bank_max = svsp_data->bank_max;
+
+	ret = svsp->probe(svsp);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return svsp;
+}
+
+static int svs_probe(struct platform_device *pdev)
+{
+	struct svs_platform *svsp;
+	unsigned int svsp_irq;
+	int ret;
+
+	svsp = svs_platform_probe(pdev);
+	if (IS_ERR(svsp)) {
+		dev_err_probe(&pdev->dev, PTR_ERR(svsp),
+			      "svs platform probe fail\n");
+		return PTR_ERR(svsp);
+	}
+
+	if (!svs_is_efuse_data_correct(svsp)) {
+		dev_notice(svsp->dev, "efuse data isn't correct\n");
+		return -EPERM;
+	}
+
+	ret = svs_bank_resource_setup(svsp);
+	if (ret) {
+		dev_err(svsp->dev, "svs bank resource setup fail: %d\n", ret);
+		return ret;
+	}
+
+	svsp_irq = irq_of_parse_and_map(svsp->dev->of_node, 0);
+	ret = devm_request_threaded_irq(svsp->dev, svsp_irq, NULL, svs_isr,
+					svsp->irqflags | IRQF_ONESHOT,
+					svsp->name, svsp);
+	if (ret) {
+		dev_err(svsp->dev, "register irq(%d) failed: %d\n",
+			svsp_irq, ret);
+		return ret;
+	}
+
+	svsp->main_clk = devm_clk_get(svsp->dev, "main");
+	if (IS_ERR(svsp->main_clk)) {
+		dev_err(svsp->dev, "failed to get clock: %ld\n",
+			PTR_ERR(svsp->main_clk));
+		return PTR_ERR(svsp->main_clk);
+	}
+
+	ret = clk_prepare_enable(svsp->main_clk);
+	if (ret) {
+		dev_err(svsp->dev, "cannot enable main clk: %d\n", ret);
+		return ret;
+	}
+
+	svsp->base = of_iomap(svsp->dev->of_node, 0);
+	if (IS_ERR_OR_NULL(svsp->base)) {
+		dev_err(svsp->dev, "cannot find svs register base\n");
+		ret = -EINVAL;
+		goto svs_probe_clk_disable;
+	}
+
+	ret = svs_start(svsp);
+	if (ret) {
+		dev_err(svsp->dev, "svs start fail: %d\n", ret);
+		goto svs_probe_iounmap;
+	}
+
+	return 0;
+
+svs_probe_iounmap:
+	iounmap(svsp->base);
+
+svs_probe_clk_disable:
+	clk_disable_unprepare(svsp->main_clk);
+
+	return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(svs_pm_ops, svs_suspend, svs_resume);
+
+static struct platform_driver svs_driver = {
+	.probe	= svs_probe,
+	.driver	= {
+		.name		= "mtk-svs",
+		.pm		= &svs_pm_ops,
+		.of_match_table	= of_match_ptr(svs_of_match),
+	},
+};
+
+module_platform_driver(svs_driver);
+
+MODULE_AUTHOR("Roger Lu <roger.lu@mediatek.com>");
+MODULE_DESCRIPTION("MediaTek SVS driver");
+MODULE_LICENSE("GPL v2");
