diff mbox series

[v6,18/20] arm64: dts: qcom: qcs404: specify per-sensor calibration cells

Message ID 20230101194034.831222-19-dmitry.baryshkov@linaro.org
State Accepted
Commit 306ccdf0786a33956a56e9a36d266d5db7040457
Headers show
Series thermal/drivers/tsens: specify nvmem cells in DT rather than parsing them manually | expand

Commit Message

Dmitry Baryshkov Jan. 1, 2023, 7:40 p.m. UTC
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404.dtsi | 145 ++++++++++++++++++++++++++-
 1 file changed, 140 insertions(+), 5 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index a5324eecb50a..84ff9df2b904 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -366,13 +366,126 @@  qfprom: qfprom@a4000 {
 			reg = <0x000a4000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			tsens_caldata: caldata@d0 {
-				reg = <0x1f8 0x14>;
-			};
 			cpr_efuse_speedbin: speedbin@13c {
 				reg = <0x13c 0x4>;
 				bits = <2 3>;
 			};
+
+			tsens_s0_p1: s0-p1@1f8 {
+				reg = <0x1f8 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s0_p2: s0-p2@1f8 {
+				reg = <0x1f8 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s1_p1: s1-p1@1f9 {
+				reg = <0x1f9 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s1_p2: s1-p2@1fa {
+				reg = <0x1fa 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s2_p1: s2-p1@1fb {
+				reg = <0x1fb 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p2: s2-p2@1fb {
+				reg = <0x1fb 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p1: s3-p1@1fc {
+				reg = <0x1fc 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p2: s3-p2@1fd {
+				reg = <0x1fd 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1: s4-p1@1fe {
+				reg = <0x1fe 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s4_p2: s4-p2@1fe {
+				reg = <0x1fe 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s5_p1: s5-p1@200 {
+				reg = <0x200 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p2: s5-p2@200 {
+				reg = <0x200 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1: s6-p1@201 {
+				reg = <0x201 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s6_p2: s6-p2@202 {
+				reg = <0x202 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s7_p1: s7-p1@203 {
+				reg = <0x203 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2: s7-p2@203 {
+				reg = <0x203 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s8_p1: s8-p1@204 {
+				reg = <0x204 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s8_p2: s8-p2@205 {
+				reg = <0x205 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s9_p1: s9-p1@206 {
+				reg = <0x206 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s9_p2: s9-p2@206 {
+				reg = <0x206 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_mode: mode@208 {
+				reg = <0x208 1>;
+				bits = <0 3>;
+			};
+
+			tsens_base1: base1@208 {
+				reg = <0x208 2>;
+				bits = <3 8>;
+			};
+
+			tsens_base2: base2@208 {
+				reg = <0x209 2>;
+				bits = <3 8>;
+			};
+
 			cpr_efuse_quot_offset1: qoffset1@231 {
 				reg = <0x231 0x4>;
 				bits = <4 7>;
@@ -447,8 +560,30 @@  tsens: thermal-sensor@4a9000 {
 			compatible = "qcom,qcs404-tsens", "qcom,tsens-v1";
 			reg = <0x004a9000 0x1000>, /* TM */
 			      <0x004a8000 0x1000>; /* SROT */
-			nvmem-cells = <&tsens_caldata>;
-			nvmem-cell-names = "calib";
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>,
+				      <&tsens_s7_p1>, <&tsens_s7_p2>,
+				      <&tsens_s8_p1>, <&tsens_s8_p2>,
+				      <&tsens_s9_p1>, <&tsens_s9_p2>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2",
+					   "s7_p1", "s7_p2",
+					   "s8_p1", "s8_p2",
+					   "s9_p1", "s9_p2";
 			#qcom,sensors = <10>;
 			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "uplow";