diff mbox series

[v3,1/2] ufs: add a quirk not to use default unipro timeout values

Message ID 1fedd3dea0ccc980913a5995a10510d86a5b01b9.1608513782.git.kwmad.kim@samsung.com
State Superseded
Headers show
Series [v3,1/2] ufs: add a quirk not to use default unipro timeout values | expand

Commit Message

Kiwoong Kim Dec. 21, 2020, 1:24 a.m. UTC 
Unipro specification says attribute IDs of the following
thing are vendor-specific values, so some SoCs could have
no regions at the defined addresses
- DME_LocalFC0ProtectionTimeOutVal
- DME_LocalTC0ReplayTimeOutVal
- DME_LocalAFC0ReqTimeOutVal

The following things should be set considering the compatibility
between host and device, so those values must not be fixed and
you could use reset values or vendor specific values
- PA_PWRMODEUSERDATA0
- PA_PWRMODEUSERDATA1
- PA_PWRMODEUSERDATA2
- PA_PWRMODEUSERDATA3
- PA_PWRMODEUSERDATA4
- PA_PWRMODEUSERDATA5

Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
---
 drivers/scsi/ufs/ufshcd.c | 40 +++++++++++++++++++++-------------------
 drivers/scsi/ufs/ufshcd.h |  6 ++++++
 2 files changed, 27 insertions(+), 19 deletions(-)
diff mbox series

Patch

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 92d433d..9d3a41d 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -4153,25 +4153,27 @@  static int ufshcd_change_power_mode(struct ufs_hba *hba,
 		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HSSERIES),
 						pwr_mode->hs_rate);
 
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA0),
-			DL_FC0ProtectionTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA1),
-			DL_TC0ReplayTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA2),
-			DL_AFC0ReqTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA3),
-			DL_FC1ProtectionTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA4),
-			DL_TC1ReplayTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA5),
-			DL_AFC1ReqTimeOutVal_Default);
-
-	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalFC0ProtectionTimeOutVal),
-			DL_FC0ProtectionTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalTC0ReplayTimeOutVal),
-			DL_TC0ReplayTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalAFC0ReqTimeOutVal),
-			DL_AFC0ReqTimeOutVal_Default);
+	if (!(hba->quirks & UFSHCD_QUIRK_SKIP_DEF_UNIPRO_TIMEOUT_SETTING)) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA0),
+				DL_FC0ProtectionTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA1),
+				DL_TC0ReplayTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA2),
+				DL_AFC0ReqTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA3),
+				DL_FC1ProtectionTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA4),
+				DL_TC1ReplayTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA5),
+				DL_AFC1ReqTimeOutVal_Default);
+
+		ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalFC0ProtectionTimeOutVal),
+				DL_FC0ProtectionTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalTC0ReplayTimeOutVal),
+				DL_TC0ReplayTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalAFC0ReqTimeOutVal),
+				DL_AFC0ReqTimeOutVal_Default);
+	}
 
 	ret = ufshcd_uic_change_pwr_mode(hba, pwr_mode->pwr_rx << 4
 			| pwr_mode->pwr_tx);
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index 61344c4..f36f73c8 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -549,6 +549,12 @@  enum ufshcd_quirks {
 	 */
 	UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL		= 1 << 12,
 
+	/*
+	 * This quirk needs to disable unipro timeout values
+	 * before power mode change
+	 */
+	UFSHCD_QUIRK_SKIP_DEF_UNIPRO_TIMEOUT_SETTING = 1 << 13,
+
 };
 
 enum ufshcd_caps {