diff mbox series

[RFC,3/5] serial: amba-pl011: Re-order APIs definition

Message ID 1595333413-30052-4-git-send-email-sumit.garg@linaro.org
State New
Headers show
Series Introduce NMI aware serial drivers | expand

Commit Message

Sumit Garg July 21, 2020, 12:10 p.m. UTC
A future patch will need to call pl011_hwinit() and
pl011_enable_interrupts() before they are currently defined. Move
them closer to the front of the file. There is no change in the
implementation of either function.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>

---
 drivers/tty/serial/amba-pl011.c | 148 ++++++++++++++++++++--------------------
 1 file changed, 74 insertions(+), 74 deletions(-)

-- 
2.7.4
diff mbox series

Patch

diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 8efd7c2..0983c5e 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1581,6 +1581,80 @@  static void pl011_break_ctl(struct uart_port *port, int break_state)
 	spin_unlock_irqrestore(&uap->port.lock, flags);
 }
 
+static int pl011_hwinit(struct uart_port *port)
+{
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
+	int retval;
+
+	/* Optionaly enable pins to be muxed in and configured */
+	pinctrl_pm_select_default_state(port->dev);
+
+	/*
+	 * Try to enable the clock producer.
+	 */
+	retval = clk_prepare_enable(uap->clk);
+	if (retval)
+		return retval;
+
+	uap->port.uartclk = clk_get_rate(uap->clk);
+
+	/* Clear pending error and receive interrupts */
+	pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS |
+		    UART011_FEIS | UART011_RTIS | UART011_RXIS,
+		    uap, REG_ICR);
+
+	/*
+	 * Save interrupts enable mask, and enable RX interrupts in case if
+	 * the interrupt is used for NMI entry.
+	 */
+	uap->im = pl011_read(uap, REG_IMSC);
+	pl011_write(UART011_RTIM | UART011_RXIM, uap, REG_IMSC);
+
+	if (dev_get_platdata(uap->port.dev)) {
+		struct amba_pl011_data *plat;
+
+		plat = dev_get_platdata(uap->port.dev);
+		if (plat->init)
+			plat->init();
+	}
+	return 0;
+}
+
+/*
+ * Enable interrupts, only timeouts when using DMA
+ * if initial RX DMA job failed, start in interrupt mode
+ * as well.
+ */
+static void pl011_enable_interrupts(struct uart_amba_port *uap)
+{
+	unsigned int i;
+
+	spin_lock_irq(&uap->port.lock);
+
+	/* Clear out any spuriously appearing RX interrupts */
+	pl011_write(UART011_RTIS | UART011_RXIS, uap, REG_ICR);
+
+	/*
+	 * RXIS is asserted only when the RX FIFO transitions from below
+	 * to above the trigger threshold.  If the RX FIFO is already
+	 * full to the threshold this can't happen and RXIS will now be
+	 * stuck off.  Drain the RX FIFO explicitly to fix this:
+	 */
+	for (i = 0; i < uap->fifosize * 2; ++i) {
+		if (pl011_read(uap, REG_FR) & UART01x_FR_RXFE)
+			break;
+
+		pl011_read(uap, REG_DR);
+	}
+
+	uap->im = UART011_RTIM;
+	if (!pl011_dma_rx_running(uap))
+		uap->im |= UART011_RXIM;
+	pl011_write(uap->im, uap, REG_IMSC);
+	spin_unlock_irq(&uap->port.lock);
+}
+
 #ifdef CONFIG_CONSOLE_POLL
 
 static void pl011_quiesce_irqs(struct uart_port *port)
@@ -1639,46 +1713,6 @@  static void pl011_put_poll_char(struct uart_port *port,
 
 #endif /* CONFIG_CONSOLE_POLL */
 
-static int pl011_hwinit(struct uart_port *port)
-{
-	struct uart_amba_port *uap =
-	    container_of(port, struct uart_amba_port, port);
-	int retval;
-
-	/* Optionaly enable pins to be muxed in and configured */
-	pinctrl_pm_select_default_state(port->dev);
-
-	/*
-	 * Try to enable the clock producer.
-	 */
-	retval = clk_prepare_enable(uap->clk);
-	if (retval)
-		return retval;
-
-	uap->port.uartclk = clk_get_rate(uap->clk);
-
-	/* Clear pending error and receive interrupts */
-	pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS |
-		    UART011_FEIS | UART011_RTIS | UART011_RXIS,
-		    uap, REG_ICR);
-
-	/*
-	 * Save interrupts enable mask, and enable RX interrupts in case if
-	 * the interrupt is used for NMI entry.
-	 */
-	uap->im = pl011_read(uap, REG_IMSC);
-	pl011_write(UART011_RTIM | UART011_RXIM, uap, REG_IMSC);
-
-	if (dev_get_platdata(uap->port.dev)) {
-		struct amba_pl011_data *plat;
-
-		plat = dev_get_platdata(uap->port.dev);
-		if (plat->init)
-			plat->init();
-	}
-	return 0;
-}
-
 static bool pl011_split_lcrh(const struct uart_amba_port *uap)
 {
 	return pl011_reg_to_offset(uap, REG_LCRH_RX) !=
@@ -1707,40 +1741,6 @@  static int pl011_allocate_irq(struct uart_amba_port *uap)
 	return request_irq(uap->port.irq, pl011_int, IRQF_SHARED, "uart-pl011", uap);
 }
 
-/*
- * Enable interrupts, only timeouts when using DMA
- * if initial RX DMA job failed, start in interrupt mode
- * as well.
- */
-static void pl011_enable_interrupts(struct uart_amba_port *uap)
-{
-	unsigned int i;
-
-	spin_lock_irq(&uap->port.lock);
-
-	/* Clear out any spuriously appearing RX interrupts */
-	pl011_write(UART011_RTIS | UART011_RXIS, uap, REG_ICR);
-
-	/*
-	 * RXIS is asserted only when the RX FIFO transitions from below
-	 * to above the trigger threshold.  If the RX FIFO is already
-	 * full to the threshold this can't happen and RXIS will now be
-	 * stuck off.  Drain the RX FIFO explicitly to fix this:
-	 */
-	for (i = 0; i < uap->fifosize * 2; ++i) {
-		if (pl011_read(uap, REG_FR) & UART01x_FR_RXFE)
-			break;
-
-		pl011_read(uap, REG_DR);
-	}
-
-	uap->im = UART011_RTIM;
-	if (!pl011_dma_rx_running(uap))
-		uap->im |= UART011_RXIM;
-	pl011_write(uap->im, uap, REG_IMSC);
-	spin_unlock_irq(&uap->port.lock);
-}
-
 static int pl011_startup(struct uart_port *port)
 {
 	struct uart_amba_port *uap =