mbox series

[0/9] thunderbolt: Offline on-board retimer NVM upgrade support

Message ID 20210519141259.84839-1-mika.westerberg@linux.intel.com
Headers show
Series thunderbolt: Offline on-board retimer NVM upgrade support | expand

Message

Mika Westerberg May 19, 2021, 2:12 p.m. UTC
Hi all,

USB4 retimers are only accessible when the USB4 is up. However, sometimes
it may be useful to be able to upgrade on-board retimers even if the link
is not up. For instance if the user simply does not have any USB4 devices.

Making retimers accessible in "offline" mode requires some help from the
platform firmware (ACPI in our case) to turn on power to the retimers and
cycle them through different modes to get the sideband link up. This may
also involve other firmwares such as Embedded Controller (as it is the case
with recent Chromebooks).

This series adds support for "offline" retimer NVM upgrade so that it first
exposes each USB4 port to the userspace. If the platform firmware provides
a special _DSM-method (Device Specific Method) under the USB4 port ACPI
description, we expose two attributes under the port that the userspace can
use to put the port to offline mode and rescan for the retimers. Otherwise
the NVM upgrade works the same way than with the online mode. We also add
documentation to the admin-guide how this can be done.

In addition to this, at least Intel USB4 devices (and retimers) allow
running NVM authenticate (upgrade) separately from write so we make it
possible for the userspace to run the write and authenticate in two steps.
This allows userspace to trigger the authentication at later time, like
when the user logs out.

Mika Westerberg (4):
  thunderbolt: Log the link as TBT instead of TBT3
  thunderbolt: Add USB4 port devices
  thunderbolt: Allow router NVM authenticate separately
  thunderbolt: Check for NVM authentication status after the operation started

Rajmohan Mani (5):
  thunderbolt: Add support for ACPI _DSM to power on/off retimers
  thunderbolt: Add additional USB4 port operations for retimer access
  thunderbolt: Add support for retimer NVM upgrade when there is no link
  thunderbolt: Move nvm_write_ops to tb.h
  thunderbolt: Add WRITE_ONLY and AUTHENTICATE_ONLY NVM operations for retimers

 .../ABI/testing/sysfs-bus-thunderbolt         |  38 ++-
 Documentation/admin-guide/thunderbolt.rst     |  29 ++
 drivers/thunderbolt/Makefile                  |   2 +-
 drivers/thunderbolt/acpi.c                    | 206 +++++++++++++
 drivers/thunderbolt/domain.c                  |   9 +-
 drivers/thunderbolt/retimer.c                 | 108 +++++--
 drivers/thunderbolt/sb_regs.h                 |   2 +
 drivers/thunderbolt/switch.c                  | 120 +++++---
 drivers/thunderbolt/tb.c                      |   4 +-
 drivers/thunderbolt/tb.h                      |  60 +++-
 drivers/thunderbolt/usb4.c                    | 153 +++++++++-
 drivers/thunderbolt/usb4_port.c               | 281 ++++++++++++++++++
 12 files changed, 930 insertions(+), 82 deletions(-)
 create mode 100644 drivers/thunderbolt/usb4_port.c

Comments

Mika Westerberg June 1, 2021, 7:56 a.m. UTC | #1
On Thu, May 20, 2021 at 10:59:12AM +0200, Greg Kroah-Hartman wrote:
> On Wed, May 19, 2021 at 05:12:50PM +0300, Mika Westerberg wrote:
> > Hi all,
> > 
> > USB4 retimers are only accessible when the USB4 is up. However, sometimes
> > it may be useful to be able to upgrade on-board retimers even if the link
> > is not up. For instance if the user simply does not have any USB4 devices.
> > 
> > Making retimers accessible in "offline" mode requires some help from the
> > platform firmware (ACPI in our case) to turn on power to the retimers and
> > cycle them through different modes to get the sideband link up. This may
> > also involve other firmwares such as Embedded Controller (as it is the case
> > with recent Chromebooks).
> > 
> > This series adds support for "offline" retimer NVM upgrade so that it first
> > exposes each USB4 port to the userspace. If the platform firmware provides
> > a special _DSM-method (Device Specific Method) under the USB4 port ACPI
> > description, we expose two attributes under the port that the userspace can
> > use to put the port to offline mode and rescan for the retimers. Otherwise
> > the NVM upgrade works the same way than with the online mode. We also add
> > documentation to the admin-guide how this can be done.
> > 
> > In addition to this, at least Intel USB4 devices (and retimers) allow
> > running NVM authenticate (upgrade) separately from write so we make it
> > possible for the userspace to run the write and authenticate in two steps.
> > This allows userspace to trigger the authentication at later time, like
> > when the user logs out.
> > 
> > Mika Westerberg (4):
> >   thunderbolt: Log the link as TBT instead of TBT3
> >   thunderbolt: Add USB4 port devices
> >   thunderbolt: Allow router NVM authenticate separately
> >   thunderbolt: Check for NVM authentication status after the operation started
> > 
> > Rajmohan Mani (5):
> >   thunderbolt: Add support for ACPI _DSM to power on/off retimers
> >   thunderbolt: Add additional USB4 port operations for retimer access
> >   thunderbolt: Add support for retimer NVM upgrade when there is no link
> >   thunderbolt: Move nvm_write_ops to tb.h
> >   thunderbolt: Add WRITE_ONLY and AUTHENTICATE_ONLY NVM operations for retimers
> 
> Looks good:
> 
> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Thanks!

All applied to thunderbolt.git/next.