diff --git a/drivers/usb/dwc3/dwc3-octeon.c b/drivers/usb/dwc3/dwc3-octeon.c
index 69bac61ccbe0..dd47498f4efb 100644
--- a/drivers/usb/dwc3/dwc3-octeon.c
+++ b/drivers/usb/dwc3/dwc3-octeon.c
@@ -258,108 +258,14 @@ static int dwc3_octeon_get_divider(void)
 	return div;
 }
 
-static int dwc3_octeon_config_power(struct device *dev, void __iomem *base)
+static int dwc3_octeon_setup(void __iomem *base,
+			     int ref_clk_sel, int ref_clk_fsel, int mpll_mul,
+			     int power_gpio, int power_active_low)
 {
-	uint32_t gpio_pwr[3];
-	int gpio, len, power_active_low;
-	struct device_node *node = dev->of_node;
-	u64 val;
-	void __iomem *uctl_host_cfg_reg = base + USBDRD_UCTL_HOST_CFG;
-
-	if (of_find_property(node, "power", &len) != NULL) {
-		if (len == 12) {
-			of_property_read_u32_array(node, "power", gpio_pwr, 3);
-			power_active_low = gpio_pwr[2] & 0x01;
-			gpio = gpio_pwr[1];
-		} else if (len == 8) {
-			of_property_read_u32_array(node, "power", gpio_pwr, 2);
-			power_active_low = 0;
-			gpio = gpio_pwr[1];
-		} else {
-			dev_err(dev, "invalid power configuration\n");
-			return -EINVAL;
-		}
-		dwc3_octeon_config_gpio(((u64)base >> 24) & 1, gpio);
-
-		/* Enable XHCI power control and set if active high or low. */
-		val = dwc3_octeon_readq(uctl_host_cfg_reg);
-		val |= USBDRD_UCTL_HOST_PPC_EN;
-		if (power_active_low)
-			val &= ~USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN;
-		else
-			val |= USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN;
-		dwc3_octeon_writeq(uctl_host_cfg_reg, val);
-	} else {
-		/* Disable XHCI power control and set if active high. */
-		val = dwc3_octeon_readq(uctl_host_cfg_reg);
-		val &= ~USBDRD_UCTL_HOST_PPC_EN;
-		val &= ~USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN;
-		dwc3_octeon_writeq(uctl_host_cfg_reg, val);
-		dev_info(dev, "power control disabled\n");
-	}
-	return 0;
-}
-
-static int dwc3_octeon_clocks_start(struct device *dev, void __iomem *base)
-{
-	int i, div, mpll_mul, ref_clk_fsel, ref_clk_sel = 2;
-	u32 clock_rate;
+	int div;
 	u64 val;
 	void __iomem *uctl_ctl_reg = base + USBDRD_UCTL_CTL;
-
-	if (dev->of_node) {
-		const char *ss_clock_type;
-		const char *hs_clock_type;
-
-		i = of_property_read_u32(dev->of_node,
-					 "refclk-frequency", &clock_rate);
-		if (i) {
-			dev_err(dev, "No UCTL \"refclk-frequency\"\n");
-			return -EINVAL;
-		}
-		i = of_property_read_string(dev->of_node,
-					    "refclk-type-ss", &ss_clock_type);
-		if (i) {
-			dev_err(dev, "No UCTL \"refclk-type-ss\"\n");
-			return -EINVAL;
-		}
-		i = of_property_read_string(dev->of_node,
-					    "refclk-type-hs", &hs_clock_type);
-		if (i) {
-			dev_err(dev, "No UCTL \"refclk-type-hs\"\n");
-			return -EINVAL;
-		}
-		if (strcmp("dlmc_ref_clk0", ss_clock_type) == 0) {
-			if (strcmp(hs_clock_type, "dlmc_ref_clk0") == 0)
-				ref_clk_sel = 0;
-			else if (strcmp(hs_clock_type, "pll_ref_clk") == 0)
-				ref_clk_sel = 2;
-			else
-				dev_warn(dev, "Invalid HS clock type %s, using pll_ref_clk instead\n",
-					 hs_clock_type);
-		} else if (strcmp(ss_clock_type, "dlmc_ref_clk1") == 0) {
-			if (strcmp(hs_clock_type, "dlmc_ref_clk1") == 0)
-				ref_clk_sel = 1;
-			else if (strcmp(hs_clock_type, "pll_ref_clk") == 0)
-				ref_clk_sel = 3;
-			else {
-				dev_warn(dev, "Invalid HS clock type %s, using pll_ref_clk instead\n",
-					 hs_clock_type);
-				ref_clk_sel = 3;
-			}
-		} else
-			dev_warn(dev, "Invalid SS clock type %s, using dlmc_ref_clk0 instead\n",
-				 ss_clock_type);
-
-		if ((ref_clk_sel == 0 || ref_clk_sel == 1) &&
-		    (clock_rate != 100000000))
-			dev_warn(dev, "Invalid UCTL clock rate of %u, using 100000000 instead\n",
-				 clock_rate);
-
-	} else {
-		dev_err(dev, "No USB UCTL device node\n");
-		return -EINVAL;
-	}
+	void __iomem *uctl_host_cfg_reg = base + USBDRD_UCTL_HOST_CFG;
 
 	/*
 	 * Step 1: Wait for all voltages to be stable...that surely
@@ -389,10 +295,8 @@ static int dwc3_octeon_clocks_start(struct device *dev, void __iomem *base)
 	dwc3_octeon_writeq(uctl_ctl_reg, val);
 	val = dwc3_octeon_readq(uctl_ctl_reg);
 	if ((div != FIELD_GET(USBDRD_UCTL_CTL_H_CLKDIV_SEL, val)) ||
-	    (!(FIELD_GET(USBDRD_UCTL_CTL_H_CLK_EN, val)))) {
-		dev_err(dev, "dwc3 controller clock init failure.\n");
-			return -EINVAL;
-	}
+	    (!(FIELD_GET(USBDRD_UCTL_CTL_H_CLK_EN, val))))
+		return -EINVAL;
 
 	/* Step 4c: Deassert the controller clock divider reset. */
 	val &= ~USBDRD_UCTL_CTL_H_CLKDIV_RST;
@@ -404,24 +308,6 @@ static int dwc3_octeon_clocks_start(struct device *dev, void __iomem *base)
 	val &= ~USBDRD_UCTL_CTL_REF_CLK_SEL;
 	val |= FIELD_PREP(USBDRD_UCTL_CTL_REF_CLK_SEL, ref_clk_sel);
 
-	ref_clk_fsel = 0x07;
-	switch (clock_rate) {
-	default:
-		dev_warn(dev, "Invalid ref_clk %u, using 100000000 instead\n",
-			 clock_rate);
-		fallthrough;
-	case 100000000:
-		mpll_mul = 0x19;
-		if (ref_clk_sel < 2)
-			ref_clk_fsel = 0x27;
-		break;
-	case 50000000:
-		mpll_mul = 0x32;
-		break;
-	case 125000000:
-		mpll_mul = 0x28;
-		break;
-	}
 	val &= ~USBDRD_UCTL_CTL_REF_CLK_FSEL;
 	val |= FIELD_PREP(USBDRD_UCTL_CTL_REF_CLK_FSEL, ref_clk_fsel);
 
@@ -452,9 +338,21 @@ static int dwc3_octeon_clocks_start(struct device *dev, void __iomem *base)
 	/* Step 8b: Wait 10 controller-clock cycles. */
 	udelay(10);
 
-	/* Steo 8c: Setup power-power control. */
-	if (dwc3_octeon_config_power(dev, base))
-		return -EINVAL;
+	/* Step 8c: Setup power control. */
+	val = dwc3_octeon_readq(uctl_host_cfg_reg);
+	val |= USBDRD_UCTL_HOST_PPC_EN;
+	if (power_gpio < 0) {
+		val &= ~USBDRD_UCTL_HOST_PPC_EN;
+	} else {
+		val |= USBDRD_UCTL_HOST_PPC_EN;
+		dwc3_octeon_config_gpio(((__force u64)base >> 24) & 1,
+					power_gpio);
+	}
+	if (power_active_low)
+		val &= ~USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN;
+	else
+		val |= USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN;
+	dwc3_octeon_writeq(uctl_host_cfg_reg, val);
 
 	/* Step 8d: Deassert UAHC reset signal. */
 	val = dwc3_octeon_readq(uctl_ctl_reg);
@@ -505,8 +403,89 @@ static void __init dwc3_octeon_phy_reset(void __iomem *base)
 static int dwc3_octeon_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
 	struct dwc3_data *data;
-	int err;
+	int err, len, ref_clk_sel, ref_clk_fsel, mpll_mul;
+	int power_active_low, power_gpio;
+	u32 clock_rate, gpio_pwr[3];
+	const char *hs_clock_type, *ss_clock_type;
+
+	if (!node) {
+		dev_err(dev, "No USB UCTL device node\n");
+		return -EINVAL;
+	}
+
+	if (of_property_read_u32(node, "refclk-frequency", &clock_rate)) {
+		dev_err(dev, "No UCTL \"refclk-frequency\"\n");
+		return -EINVAL;
+	}
+	if (of_property_read_string(node, "refclk-type-ss", &ss_clock_type)) {
+		dev_err(dev, "No UCTL \"refclk-type-ss\"\n");
+		return -EINVAL;
+	}
+	if (of_property_read_string(node, "refclk-type-hs", &hs_clock_type)) {
+		dev_err(dev, "No UCTL \"refclk-type-hs\"\n");
+		return -EINVAL;
+	}
+
+	ref_clk_sel = 2;
+	if (strcmp("dlmc_ref_clk0", ss_clock_type) == 0) {
+		if (strcmp(hs_clock_type, "dlmc_ref_clk0") == 0)
+			ref_clk_sel = 0;
+		else if (strcmp(hs_clock_type, "pll_ref_clk"))
+			dev_warn(dev, "Invalid HS clock type %s, using pll_ref_clk instead\n",
+				 hs_clock_type);
+	} else if (strcmp(ss_clock_type, "dlmc_ref_clk1") == 0) {
+		if (strcmp(hs_clock_type, "dlmc_ref_clk1") == 0) {
+			ref_clk_sel = 1;
+		} else {
+			ref_clk_sel = 3;
+			if (strcmp(hs_clock_type, "pll_ref_clk"))
+				dev_warn(dev, "Invalid HS clock type %s, using pll_ref_clk instead\n",
+					 hs_clock_type);
+		}
+	} else {
+		dev_warn(dev, "Invalid SS clock type %s, using dlmc_ref_clk0 instead\n",
+			 ss_clock_type);
+	}
+
+	ref_clk_fsel = 0x07;
+	switch (clock_rate) {
+	default:
+		dev_warn(dev, "Invalid ref_clk %u, using 100000000 instead\n",
+			 clock_rate);
+		fallthrough;
+	case 100000000:
+		mpll_mul = 0x19;
+		if (ref_clk_sel < 2)
+			ref_clk_fsel = 0x27;
+		break;
+	case 50000000:
+		mpll_mul = 0x32;
+		break;
+	case 125000000:
+		mpll_mul = 0x28;
+		break;
+	}
+
+	if (of_find_property(node, "power", &len)) {
+		if (len == 12) {
+			of_property_read_u32_array(node, "power", gpio_pwr, 3);
+			power_active_low = gpio_pwr[2] & 0x01;
+			power_gpio = gpio_pwr[1];
+		} else if (len == 8) {
+			of_property_read_u32_array(node, "power", gpio_pwr, 2);
+			power_active_low = 0;
+			power_gpio = gpio_pwr[1];
+		} else {
+			dev_err(dev, "invalid power configuration\n");
+			return -EINVAL;
+		}
+	} else {
+		power_gpio = -1;
+		power_active_low = 0;
+		dev_info(dev, "power control disabled\n");
+	}
 
 	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
 	if (!data)
@@ -516,9 +495,12 @@ static int dwc3_octeon_probe(struct platform_device *pdev)
 	if (IS_ERR(data->base))
 		return PTR_ERR(data->base);
 
-	err = dwc3_octeon_clocks_start(dev, data->base);
-	if (err)
+	err = dwc3_octeon_setup(data->base, ref_clk_sel, ref_clk_fsel,
+				mpll_mul, power_gpio, power_active_low);
+	if (err) {
+		dev_err(dev, "controller init failure\n");
 		return err;
+	}
 
 	dwc3_octeon_set_endian_mode(data->base);
 	dwc3_octeon_phy_reset(data->base);
