@@ -40,6 +40,9 @@ MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
#define AST2600_SCU_SYS_RESET_WDT_SW_MASK 0x8
#define AST2600_SCU_SYS_RESET_WDT_MASK_SHIFT 16
+/* WDT behavior control flag */
+#define WDT_RESTART_SYSTEM_SW_SUPPORT 0x00000001
+
struct aspeed_wdt_scu {
const char *compatible;
u32 reset_status_reg;
@@ -53,6 +56,7 @@ struct aspeed_wdt_config {
u32 irq_shift;
u32 irq_mask;
struct aspeed_wdt_scu scu;
+ u32 flags;
};
struct aspeed_wdt {
@@ -67,6 +71,7 @@ static const struct aspeed_wdt_config ast2400_config = {
.ext_pulse_width_mask = 0xff,
.irq_shift = 0,
.irq_mask = 0,
+ .flags = 0,
.scu = {
.compatible = "aspeed,ast2400-scu",
.reset_status_reg = AST2400_SCU_SYS_RESET_STATUS,
@@ -80,6 +85,7 @@ static const struct aspeed_wdt_config ast2500_config = {
.ext_pulse_width_mask = 0xfffff,
.irq_shift = 12,
.irq_mask = GENMASK(31, 12),
+ .flags = 0,
.scu = {
.compatible = "aspeed,ast2500-scu",
.reset_status_reg = AST2400_SCU_SYS_RESET_STATUS,
@@ -93,6 +99,7 @@ static const struct aspeed_wdt_config ast2600_config = {
.ext_pulse_width_mask = 0xfffff,
.irq_shift = 0,
.irq_mask = GENMASK(31, 10),
+ .flags = WDT_RESTART_SYSTEM_SW_SUPPORT,
.scu = {
.compatible = "aspeed,ast2600-scu",
.reset_status_reg = AST2600_SCU_SYS_RESET_STATUS,
@@ -130,6 +137,11 @@ MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0)
#define WDT_RESET_MASK1 0x1c
#define WDT_RESET_MASK2 0x20
+#define WDT_SW_RESET_CTRL 0x24
+#define WDT_SW_RESET_COUNT_CLEAR 0xDEADDEAD
+#define WDT_SW_RESET_ENABLE 0xAEEDF123
+#define WDT_SW_RESET_MASK1 0x28
+#define WDT_SW_RESET_MASK2 0x2c
/*
* WDT_RESET_WIDTH controls the characteristics of the external pulse (if
@@ -249,10 +261,31 @@ static int aspeed_wdt_set_pretimeout(struct watchdog_device *wdd,
return 0;
}
+static void aspeed_wdt_sw_reset(struct watchdog_device *wdd)
+{
+ struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
+ u32 ctrl = WDT_CTRL_RESET_MODE_SOC |
+ WDT_CTRL_RESET_SYSTEM;
+
+ writel(ctrl, wdt->base + WDT_CTRL);
+ writel(WDT_SW_RESET_COUNT_CLEAR,
+ wdt->base + WDT_SW_RESET_CTRL);
+ writel(WDT_SW_RESET_ENABLE, wdt->base + WDT_SW_RESET_CTRL);
+
+ /* system must be reset immediately */
+ mdelay(1000);
+}
+
static int aspeed_wdt_restart(struct watchdog_device *wdd,
unsigned long action, void *data)
{
struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
+ struct aspeed_wdt_config *cfg = wdt->cfg;
+
+ if (cfg->flags & WDT_RESTART_SYSTEM_SW_SUPPORT) {
+ aspeed_wdt_sw_reset(wdd);
+ return 0;
+ }
wdt->ctrl &= ~WDT_CTRL_BOOT_SECONDARY;
aspeed_wdt_enable(wdt, 128 * WDT_RATE_1MHZ / 1000);
@@ -524,6 +557,13 @@ static int aspeed_wdt_probe(struct platform_device *pdev)
if (nrstmask > 1)
writel(reset_mask[1], wdt->base + WDT_RESET_MASK2);
}
+
+ if (wdt->cfg->flags & WDT_RESTART_SYSTEM_SW_SUPPORT) {
+ reg = readl(wdt->base + WDT_RESET_MASK1);
+ writel(reg, wdt->base + WDT_SW_RESET_MASK1);
+ reg = readl(wdt->base + WDT_RESET_MASK2);
+ writel(reg, wdt->base + WDT_SW_RESET_MASK2);
+ }
}
if (!of_property_read_u32(np, "aspeed,ext-pulse-duration", &duration)) {
Since AST2600, except for HW WDT counter timeout, HW WDT reset can also be triggered by just cinfiguring some HW registers by SW directly. We named it "SW restart". Although it is "SW" restart, its mechanism is implemented by HW. Originally, system can only know it is reset by WDT through a reset flag. However, since AST2600, SW can trigger the reset event consciously and directly without wait for WDT timeout. WDT counter is not enabled when SW restart is adopted. After that, an independent reset event flag will be set after systemis reset by SW. Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com> --- drivers/watchdog/aspeed_wdt.c | 40 +++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+)