diff --git a/drivers/net/wireless/realtek/rtl8xxxu/Kconfig b/drivers/net/wireless/realtek/rtl8xxxu/Kconfig
index 631d078278be..091d3ad98093 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/Kconfig
+++ b/drivers/net/wireless/realtek/rtl8xxxu/Kconfig
@@ -10,7 +10,7 @@ config RTL8XXXU
 	  parts written to utilize the Linux mac80211 stack.
 	  The driver is known to work with a number of RTL8723AU,
 	  RL8188CU, RTL8188RU, RTL8191CU, RTL8192CU, RTL8723BU, RTL8192EU,
-	  and RTL8188FU devices.
+	  RTL8188FU, and RTL8188EU devices.
 
 	  This driver is under development and has a limited feature
 	  set. In particular it does not yet support 40MHz channels
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/Makefile b/drivers/net/wireless/realtek/rtl8xxxu/Makefile
index c4ad5325f5e7..0cb58fb30228 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/Makefile
+++ b/drivers/net/wireless/realtek/rtl8xxxu/Makefile
@@ -2,4 +2,5 @@
 obj-$(CONFIG_RTL8XXXU)	+= rtl8xxxu.o
 
 rtl8xxxu-y	:= rtl8xxxu_core.o rtl8xxxu_8192e.o rtl8xxxu_8723b.o \
-		   rtl8xxxu_8723a.o rtl8xxxu_8192c.o rtl8xxxu_8188f.o
+		   rtl8xxxu_8723a.o rtl8xxxu_8192c.o rtl8xxxu_8188f.o \
+		   rtl8xxxu_8188e.o
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
index 15bb2b5211a8..29f5dbee16b0 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
@@ -36,6 +36,7 @@
 
 #define TX_TOTAL_PAGE_NUM		0xf8
 #define TX_TOTAL_PAGE_NUM_8188F		0xf7
+#define TX_TOTAL_PAGE_NUM_8188E		0xa9
 #define TX_TOTAL_PAGE_NUM_8192E		0xf3
 #define TX_TOTAL_PAGE_NUM_8723B		0xf7
 /* (HPQ + LPQ + NPQ + PUBQ) = TX_TOTAL_PAGE_NUM */
@@ -49,6 +50,11 @@
 #define TX_PAGE_NUM_LO_PQ_8188F		0x02
 #define TX_PAGE_NUM_NORM_PQ_8188F	0x02
 
+#define TX_PAGE_NUM_PUBQ_8188E		0x47
+#define TX_PAGE_NUM_HI_PQ_8188E		0x29
+#define TX_PAGE_NUM_LO_PQ_8188E		0x1c
+#define TX_PAGE_NUM_NORM_PQ_8188E	0x1c
+
 #define TX_PAGE_NUM_PUBQ_8192E		0xe7
 #define TX_PAGE_NUM_HI_PQ_8192E		0x08
 #define TX_PAGE_NUM_LO_PQ_8192E		0x0c
@@ -153,7 +159,8 @@ struct rtl8xxxu_rxdesc16 {
 	u32 htc:1;
 	u32 eosp:1;
 	u32 bssidfit:2;
-	u32 reserved1:16;
+	u32 rpt_sel:2;		/* 8188e */
+	u32 reserved1:14;
 	u32 unicastwake:1;
 	u32 magicwake:1;
 
@@ -211,7 +218,8 @@ struct rtl8xxxu_rxdesc16 {
 
 	u32 magicwake:1;
 	u32 unicastwake:1;
-	u32 reserved1:16;
+	u32 reserved1:14;
+	u32 rpt_sel:2;		/* 8188e */
 	u32 bssidfit:2;
 	u32 eosp:1;
 	u32 htc:1;
@@ -502,6 +510,8 @@ struct rtl8xxxu_txdesc40 {
 #define TXDESC_AMPDU_DENSITY_SHIFT	20
 #define TXDESC40_BT_INT			BIT(23)
 #define TXDESC40_GID_SHIFT		24
+#define TXDESC_ANTENNA_SELECT_A		BIT(24)
+#define TXDESC_ANTENNA_SELECT_B		BIT(25)
 
 /* Word 3 */
 #define TXDESC40_USE_DRIVER_RATE	BIT(8)
@@ -546,6 +556,10 @@ struct rtl8xxxu_txdesc40 {
 
 /* Word 6 */
 #define TXDESC_MAX_AGG_SHIFT		11
+#define TXDESC_USB_TX_AGG_SHIT		24
+
+/* Word 7 */
+#define TXDESC_ANTENNA_SELECT_C		BIT(29)
 
 /* Word 8 */
 #define TXDESC40_HW_SEQ_ENABLE		BIT(15)
@@ -912,6 +926,42 @@ struct rtl8188fu_efuse {
 	u8 res11[0xc3];
 };
 
+struct rtl8188eu_efuse {
+	__le16 rtl_id;
+	u8 res0[0x0e];
+	struct rtl8192eu_efuse_tx_power tx_power_index_A;	/* 0x10 */
+	u8 res1[0x7e];			/* 0x3a */
+	u8 channel_plan;		/* 0xb8 */
+	u8 xtal_k;
+	u8 thermal_meter;
+	u8 iqk_lck;
+	u8 res2[5];
+	u8 rf_board_option;
+	u8 rf_feature_option;
+	u8 rf_bt_setting;
+	u8 eeprom_version;
+	u8 eeprom_customer_id;
+	u8 res3[3];
+	u8 rf_antenna_option;		/* 0xc9 */
+	u8 res4[6];
+	u8 vid;				/* 0xd0 */
+	u8 res5[1];
+	u8 pid;				/* 0xd2 */
+	u8 res6[1];
+	u8 usb_optional_function;
+	u8 res7[2];
+	u8 mac_addr[ETH_ALEN];		/* 0xd7 */
+	u8 res8[2];
+	u8 vendor_name[7];
+	u8 res9[2];
+	u8 device_name[0x0b];		/* 0xe8 */
+	u8 res10[2];
+	u8 serial[0x0b];		/* 0xf5 */
+	u8 res11[0x30];
+	u8 unknown[0x0d];		/* 0x130 */
+	u8 res12[0xc3];
+} __packed;
+
 struct rtl8xxxu_reg8val {
 	u16 reg;
 	u8 val;
@@ -1435,6 +1485,7 @@ struct rtl8xxxu_priv {
 		struct rtl8192cu_efuse efuse8192;
 		struct rtl8192eu_efuse efuse8192eu;
 		struct rtl8188fu_efuse efuse8188fu;
+		struct rtl8188eu_efuse efuse8188eu;
 	} efuse_wifi;
 	u32 adda_backup[RTL8XXXU_ADDA_REGS];
 	u32 mac_backup[RTL8XXXU_MAC_REGS];
@@ -1526,6 +1577,7 @@ struct rtl8xxxu_fileops {
 	u8 page_num_hi;
 	u8 page_num_lo;
 	u8 page_num_norm;
+	u8 last_llt_entry;
 };
 
 extern int rtl8xxxu_debug;
@@ -1585,6 +1637,8 @@ void rtl8xxxu_gen1_phy_iq_calibrate(struct rtl8xxxu_priv *priv);
 void rtl8xxxu_gen1_init_phy_bb(struct rtl8xxxu_priv *priv);
 void rtl8xxxu_gen1_set_tx_power(struct rtl8xxxu_priv *priv,
 				int channel, bool ht40);
+void rtl8188f_set_tx_power(struct rtl8xxxu_priv *priv,
+			   int channel, bool ht40);
 void rtl8xxxu_gen1_config_channel(struct ieee80211_hw *hw);
 void rtl8xxxu_gen2_config_channel(struct ieee80211_hw *hw);
 void rtl8xxxu_gen1_usb_quirks(struct rtl8xxxu_priv *priv);
@@ -1605,6 +1659,8 @@ void rtl8xxxu_init_burst(struct rtl8xxxu_priv *priv);
 int rtl8xxxu_parse_rxdesc16(struct rtl8xxxu_priv *priv, struct sk_buff *skb);
 int rtl8xxxu_parse_rxdesc24(struct rtl8xxxu_priv *priv, struct sk_buff *skb);
 int rtl8xxxu_gen2_channel_to_group(int channel);
+bool rtl8xxxu_simularity_compare(struct rtl8xxxu_priv *priv,
+				 int result[][8], int c1, int c2);
 bool rtl8xxxu_gen2_simularity_compare(struct rtl8xxxu_priv *priv,
 				      int result[][8], int c1, int c2);
 void rtl8xxxu_fill_txdesc_v1(struct ieee80211_hw *hw, struct ieee80211_hdr *hdr,
@@ -1617,13 +1673,20 @@ void rtl8xxxu_fill_txdesc_v2(struct ieee80211_hw *hw, struct ieee80211_hdr *hdr,
 			     struct rtl8xxxu_txdesc32 *tx_desc32, bool sgi,
 			     bool short_preamble, bool ampdu_enable,
 			     u32 rts_rate);
+void rtl8xxxu_fill_txdesc_v3(struct ieee80211_hw *hw, struct ieee80211_hdr *hdr,
+			     struct ieee80211_tx_info *tx_info,
+			     struct rtl8xxxu_txdesc32 *tx_desc32, bool sgi,
+			     bool short_preamble, bool ampdu_enable,
+			     u32 rts_rate);
 void rtl8723bu_set_ps_tdma(struct rtl8xxxu_priv *priv,
 			   u8 arg1, u8 arg2, u8 arg3, u8 arg4, u8 arg5);
 void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv);
 void rtl8723a_set_crystal_cap(struct rtl8xxxu_priv *priv, u8 crystal_cap);
+void rtl8188f_set_crystal_cap(struct rtl8xxxu_priv *priv, u8 crystal_cap);
 s8 rtl8723a_cck_rssi(struct rtl8xxxu_priv *priv, u8 cck_agc_rpt);
 
 extern struct rtl8xxxu_fileops rtl8188fu_fops;
+extern struct rtl8xxxu_fileops rtl8188eu_fops;
 extern struct rtl8xxxu_fileops rtl8192cu_fops;
 extern struct rtl8xxxu_fileops rtl8192eu_fops;
 extern struct rtl8xxxu_fileops rtl8723au_fops;
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8188e.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8188e.c
new file mode 100644
index 000000000000..ae9a2bec1643
--- /dev/null
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8188e.c
@@ -0,0 +1,1280 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * RTL8XXXU mac80211 USB driver - 8188e specific subdriver
+ *
+ * Copyright (c) 2014 - 2016 Jes Sorensen <Jes.Sorensen@gmail.com>
+ *
+ * Portions, notably calibration code:
+ * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
+ *
+ * This driver was written as a replacement for the vendor provided
+ * rtl8723au driver. As the Realtek 8xxx chips are very similar in
+ * their programming interface, I have started adding support for
+ * additional 8xxx chips like the 8192cu, 8188cus, etc.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/list.h>
+#include <linux/usb.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/wireless.h>
+#include <linux/firmware.h>
+#include <linux/moduleparam.h>
+#include <net/mac80211.h>
+#include "rtl8xxxu.h"
+#include "rtl8xxxu_regs.h"
+
+static const struct rtl8xxxu_reg8val rtl8188e_mac_init_table[] = {
+	{0x026, 0x41}, {0x027, 0x35}, {0x040, 0x00}, {0x421, 0x0f},
+	{0x428, 0x0a}, {0x429, 0x10}, {0x430, 0x00}, {0x431, 0x01},
+	{0x432, 0x02}, {0x433, 0x04}, {0x434, 0x05}, {0x435, 0x06},
+	{0x436, 0x07}, {0x437, 0x08}, {0x438, 0x00}, {0x439, 0x00},
+	{0x43a, 0x01}, {0x43b, 0x02}, {0x43c, 0x04}, {0x43d, 0x05},
+	{0x43e, 0x06}, {0x43f, 0x07}, {0x440, 0x5d}, {0x441, 0x01},
+	{0x442, 0x00}, {0x444, 0x15}, {0x445, 0xf0}, {0x446, 0x0f},
+	{0x447, 0x00}, {0x458, 0x41}, {0x459, 0xa8}, {0x45a, 0x72},
+	{0x45b, 0xb9}, {0x460, 0x66}, {0x461, 0x66}, {0x480, 0x08},
+	{0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff}, {0x4cd, 0xff},
+	{0x4ce, 0x01}, {0x4d3, 0x01}, {0x500, 0x26}, {0x501, 0xa2},
+	{0x502, 0x2f}, {0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3},
+	{0x506, 0x5e}, {0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4},
+	{0x50a, 0x5e}, {0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4},
+	{0x50e, 0x00}, {0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a},
+	{0x516, 0x0a}, {0x525, 0x4f}, {0x550, 0x10}, {0x551, 0x10},
+	{0x559, 0x02}, {0x55d, 0xff}, {0x605, 0x30}, {0x608, 0x0e},
+	{0x609, 0x2a}, {0x620, 0xff}, {0x621, 0xff}, {0x622, 0xff},
+	{0x623, 0xff}, {0x624, 0xff}, {0x625, 0xff}, {0x626, 0xff},
+	{0x627, 0xff}, {0x63c, 0x08}, {0x63d, 0x08}, {0x63e, 0x0c},
+	{0x63f, 0x0c}, {0x640, 0x40}, {0x652, 0x20}, {0x66e, 0x05},
+	{0x700, 0x21}, {0x701, 0x43}, {0x702, 0x65}, {0x703, 0x87},
+	{0x708, 0x21}, {0x709, 0x43}, {0x70a, 0x65}, {0x70b, 0x87},
+	{0xffff, 0xff},
+};
+
+static const struct rtl8xxxu_reg32val rtl8188eu_phy_init_table[] = {
+	{0x800, 0x80040000}, {0x804, 0x00000003},
+	{0x808, 0x0000fc00}, {0x80c, 0x0000000a},
+	{0x810, 0x10001331}, {0x814, 0x020c3d10},
+	{0x818, 0x02200385}, {0x81c, 0x00000000},
+	{0x820, 0x01000100}, {0x824, 0x00390204},
+	{0x828, 0x00000000}, {0x82c, 0x00000000},
+	{0x830, 0x00000000}, {0x834, 0x00000000},
+	{0x838, 0x00000000}, {0x83c, 0x00000000},
+	{0x840, 0x00010000}, {0x844, 0x00000000},
+	{0x848, 0x00000000}, {0x84c, 0x00000000},
+	{0x850, 0x00000000}, {0x854, 0x00000000},
+	{0x858, 0x569a11a9}, {0x85c, 0x01000014},
+	{0x860, 0x66f60110}, {0x864, 0x061f0649},
+	{0x868, 0x00000000}, {0x86c, 0x27272700},
+	{0x870, 0x07000760}, {0x874, 0x25004000},
+	{0x878, 0x00000808}, {0x87c, 0x00000000},
+	{0x880, 0xb0000c1c}, {0x884, 0x00000001},
+	{0x888, 0x00000000}, {0x88c, 0xccc000c0},
+	{0x890, 0x00000800}, {0x894, 0xfffffffe},
+	{0x898, 0x40302010}, {0x89c, 0x00706050},
+	{0x900, 0x00000000}, {0x904, 0x00000023},
+	{0x908, 0x00000000}, {0x90c, 0x81121111},
+	{0x910, 0x00000002}, {0x914, 0x00000201},
+	{0xa00, 0x00d047c8}, {0xa04, 0x80ff800c},
+	{0xa08, 0x8c838300}, {0xa0c, 0x2e7f120f},
+	{0xa10, 0x9500bb7e}, {0xa14, 0x1114d028},
+	{0xa18, 0x00881117}, {0xa1c, 0x89140f00},
+	{0xa20, 0x1a1b0000}, {0xa24, 0x090e1317},
+	{0xa28, 0x00000204}, {0xa2c, 0x00d30000},
+	{0xa70, 0x101fbf00}, {0xa74, 0x00000007},
+	{0xa78, 0x00000900}, {0xa7c, 0x225b0606},
+	{0xa80, 0x218075b1}, {0xb2c, 0x80000000},
+	{0xc00, 0x48071d40}, {0xc04, 0x03a05611},
+	{0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c},
+	{0xc10, 0x08800000}, {0xc14, 0x40000100},
+	{0xc18, 0x08800000}, {0xc1c, 0x40000100},
+	{0xc20, 0x00000000}, {0xc24, 0x00000000},
+	{0xc28, 0x00000000}, {0xc2c, 0x00000000},
+	{0xc30, 0x69e9ac47}, {0xc34, 0x469652af},
+	{0xc38, 0x49795994}, {0xc3c, 0x0a97971c},
+	{0xc40, 0x1f7c403f}, {0xc44, 0x000100b7},
+	{0xc48, 0xec020107}, {0xc4c, 0x007f037f},
+	{0xc50, 0x69553420}, {0xc54, 0x43bc0094},
+	{0xc58, 0x00013169}, {0xc5c, 0x00250492},
+	{0xc60, 0x00000000}, {0xc64, 0x7112848b},
+	{0xc68, 0x47c00bff}, {0xc6c, 0x00000036},
+	{0xc70, 0x2c7f000d}, {0xc74, 0x020610db},
+	{0xc78, 0x0000001f}, {0xc7c, 0x00b91612},
+	{0xc80, 0x390000e4}, {0xc84, 0x21f60000},
+	{0xc88, 0x40000100}, {0xc8c, 0x20200000},
+	{0xc90, 0x00091521}, {0xc94, 0x00000000},
+	{0xc98, 0x00121820}, {0xc9c, 0x00007f7f},
+	{0xca0, 0x00000000}, {0xca4, 0x000300a0},
+	{0xca8, 0x00000000}, {0xcac, 0x00000000},
+	{0xcb0, 0x00000000}, {0xcb4, 0x00000000},
+	{0xcb8, 0x00000000}, {0xcbc, 0x28000000},
+	{0xcc0, 0x00000000}, {0xcc4, 0x00000000},
+	{0xcc8, 0x00000000}, {0xccc, 0x00000000},
+	{0xcd0, 0x00000000}, {0xcd4, 0x00000000},
+	{0xcd8, 0x64b22427}, {0xcdc, 0x00766932},
+	{0xce0, 0x00222222}, {0xce4, 0x00000000},
+	{0xce8, 0x37644302}, {0xcec, 0x2f97d40c},
+	{0xd00, 0x00000740}, {0xd04, 0x00020401},
+	{0xd08, 0x0000907f}, {0xd0c, 0x20010201},
+	{0xd10, 0xa0633333}, {0xd14, 0x3333bc43},
+	{0xd18, 0x7a8f5b6f}, {0xd2c, 0xcc979975},
+	{0xd30, 0x00000000}, {0xd34, 0x80608000},
+	{0xd38, 0x00000000}, {0xd3c, 0x00127353},
+	{0xd40, 0x00000000}, {0xd44, 0x00000000},
+	{0xd48, 0x00000000}, {0xd4c, 0x00000000},
+	{0xd50, 0x6437140a}, {0xd54, 0x00000000},
+	{0xd58, 0x00000282}, {0xd5c, 0x30032064},
+	{0xd60, 0x4653de68}, {0xd64, 0x04518a3c},
+	{0xd68, 0x00002101}, {0xd6c, 0x2a201c16},
+	{0xd70, 0x1812362e}, {0xd74, 0x322c2220},
+	{0xd78, 0x000e3c24}, {0xe00, 0x2d2d2d2d},
+	{0xe04, 0x2d2d2d2d}, {0xe08, 0x0390272d},
+	{0xe10, 0x2d2d2d2d}, {0xe14, 0x2d2d2d2d},
+	{0xe18, 0x2d2d2d2d}, {0xe1c, 0x2d2d2d2d},
+	{0xe28, 0x00000000}, {0xe30, 0x1000dc1f},
+	{0xe34, 0x10008c1f}, {0xe38, 0x02140102},
+	{0xe3c, 0x681604c2}, {0xe40, 0x01007c00},
+	{0xe44, 0x01004800}, {0xe48, 0xfb000000},
+	{0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f},
+	{0xe54, 0x10008c1f}, {0xe58, 0x02140102},
+	{0xe5c, 0x28160d05}, {0xe60, 0x00000048},
+	{0xe68, 0x001b25a4}, {0xe6c, 0x00c00014},
+	{0xe70, 0x00c00014}, {0xe74, 0x01000014},
+	{0xe78, 0x01000014}, {0xe7c, 0x01000014},
+	{0xe80, 0x01000014}, {0xe84, 0x00c00014},
+	{0xe88, 0x01000014}, {0xe8c, 0x00c00014},
+	{0xed0, 0x00c00014}, {0xed4, 0x00c00014},
+	{0xed8, 0x00c00014}, {0xedc, 0x00000014},
+	{0xee0, 0x00000014}, {0xee8, 0x21555448},
+	{0xeec, 0x01c00014}, {0xf14, 0x00000003},
+	{0xf4c, 0x00000000}, {0xf00, 0x00000300},
+	{0xffff, 0xffffffff},
+};
+
+static const struct rtl8xxxu_reg32val rtl8188e_agc_table[] = {
+	{0xc78, 0xfb000001}, {0xc78, 0xfb010001},
+	{0xc78, 0xfb020001}, {0xc78, 0xfb030001},
+	{0xc78, 0xfb040001}, {0xc78, 0xfb050001},
+	{0xc78, 0xfa060001}, {0xc78, 0xf9070001},
+	{0xc78, 0xf8080001}, {0xc78, 0xf7090001},
+	{0xc78, 0xf60a0001}, {0xc78, 0xf50b0001},
+	{0xc78, 0xf40c0001}, {0xc78, 0xf30d0001},
+	{0xc78, 0xf20e0001}, {0xc78, 0xf10f0001},
+	{0xc78, 0xf0100001}, {0xc78, 0xef110001},
+	{0xc78, 0xee120001}, {0xc78, 0xed130001},
+	{0xc78, 0xec140001}, {0xc78, 0xeb150001},
+	{0xc78, 0xea160001}, {0xc78, 0xe9170001},
+	{0xc78, 0xe8180001}, {0xc78, 0xe7190001},
+	{0xc78, 0xe61a0001}, {0xc78, 0xe51b0001},
+	{0xc78, 0xe41c0001}, {0xc78, 0xe31d0001},
+	{0xc78, 0xe21e0001}, {0xc78, 0xe11f0001},
+	{0xc78, 0x8a200001}, {0xc78, 0x89210001},
+	{0xc78, 0x88220001}, {0xc78, 0x87230001},
+	{0xc78, 0x86240001}, {0xc78, 0x85250001},
+	{0xc78, 0x84260001}, {0xc78, 0x83270001},
+	{0xc78, 0x82280001}, {0xc78, 0x6b290001},
+	{0xc78, 0x6a2a0001}, {0xc78, 0x692b0001},
+	{0xc78, 0x682c0001}, {0xc78, 0x672d0001},
+	{0xc78, 0x662e0001}, {0xc78, 0x652f0001},
+	{0xc78, 0x64300001}, {0xc78, 0x63310001},
+	{0xc78, 0x62320001}, {0xc78, 0x61330001},
+	{0xc78, 0x46340001}, {0xc78, 0x45350001},
+	{0xc78, 0x44360001}, {0xc78, 0x43370001},
+	{0xc78, 0x42380001}, {0xc78, 0x41390001},
+	{0xc78, 0x403a0001}, {0xc78, 0x403b0001},
+	{0xc78, 0x403c0001}, {0xc78, 0x403d0001},
+	{0xc78, 0x403e0001}, {0xc78, 0x403f0001},
+	{0xc78, 0xfb400001}, {0xc78, 0xfb410001},
+	{0xc78, 0xfb420001}, {0xc78, 0xfb430001},
+	{0xc78, 0xfb440001}, {0xc78, 0xfb450001},
+	{0xc78, 0xfb460001}, {0xc78, 0xfb470001},
+	{0xc78, 0xfb480001}, {0xc78, 0xfa490001},
+	{0xc78, 0xf94a0001}, {0xc78, 0xf84b0001},
+	{0xc78, 0xf74c0001}, {0xc78, 0xf64d0001},
+	{0xc78, 0xf54e0001}, {0xc78, 0xf44f0001},
+	{0xc78, 0xf3500001}, {0xc78, 0xf2510001},
+	{0xc78, 0xf1520001}, {0xc78, 0xf0530001},
+	{0xc78, 0xef540001}, {0xc78, 0xee550001},
+	{0xc78, 0xed560001}, {0xc78, 0xec570001},
+	{0xc78, 0xeb580001}, {0xc78, 0xea590001},
+	{0xc78, 0xe95a0001}, {0xc78, 0xe85b0001},
+	{0xc78, 0xe75c0001}, {0xc78, 0xe65d0001},
+	{0xc78, 0xe55e0001}, {0xc78, 0xe45f0001},
+	{0xc78, 0xe3600001}, {0xc78, 0xe2610001},
+	{0xc78, 0xc3620001}, {0xc78, 0xc2630001},
+	{0xc78, 0xc1640001}, {0xc78, 0x8b650001},
+	{0xc78, 0x8a660001}, {0xc78, 0x89670001},
+	{0xc78, 0x88680001}, {0xc78, 0x87690001},
+	{0xc78, 0x866a0001}, {0xc78, 0x856b0001},
+	{0xc78, 0x846c0001}, {0xc78, 0x676d0001},
+	{0xc78, 0x666e0001}, {0xc78, 0x656f0001},
+	{0xc78, 0x64700001}, {0xc78, 0x63710001},
+	{0xc78, 0x62720001}, {0xc78, 0x61730001},
+	{0xc78, 0x60740001}, {0xc78, 0x46750001},
+	{0xc78, 0x45760001}, {0xc78, 0x44770001},
+	{0xc78, 0x43780001}, {0xc78, 0x42790001},
+	{0xc78, 0x417a0001}, {0xc78, 0x407b0001},
+	{0xc78, 0x407c0001}, {0xc78, 0x407d0001},
+	{0xc78, 0x407e0001}, {0xc78, 0x407f0001},
+	{0xc50, 0x69553422}, {0xc50, 0x69553420},
+	{0xffff, 0xffffffff}
+};
+
+static const struct rtl8xxxu_rfregval rtl8188eu_radioa_init_table[] = {
+	{0x00, 0x00030000}, {0x08, 0x00084000},
+	{0x18, 0x00000407}, {0x19, 0x00000012},
+	{0x1e, 0x00080009}, {0x1f, 0x00000880},
+	{0x2f, 0x0001a060}, {0x3f, 0x00000000},
+	{0x42, 0x000060c0}, {0x57, 0x000d0000},
+	{0x58, 0x000be180}, {0x67, 0x00001552},
+	{0x83, 0x00000000}, {0xb0, 0x000ff8fc},
+	{0xb1, 0x00054400}, {0xb2, 0x000ccc19},
+	{0xb4, 0x00043003}, {0xb6, 0x0004953e},
+	{0xb7, 0x0001c718}, {0xb8, 0x000060ff},
+	{0xb9, 0x00080001}, {0xba, 0x00040000},
+	{0xbb, 0x00000400}, {0xbf, 0x000c0000},
+	{0xc2, 0x00002400}, {0xc3, 0x00000009},
+	{0xc4, 0x00040c91}, {0xc5, 0x00099999},
+	{0xc6, 0x000000a3}, {0xc7, 0x00088820},
+	{0xc8, 0x00076c06}, {0xc9, 0x00000000},
+	{0xca, 0x00080000}, {0xdf, 0x00000180},
+	{0xef, 0x000001a0}, {0x51, 0x0006b27d},
+	{0x52, 0x0007e49d},	/* Set to 0x0007e4dd for SDIO */
+	{0x53, 0x00000073}, {0x56, 0x00051ff3},
+	{0x35, 0x00000086}, {0x35, 0x00000186},
+	{0x35, 0x00000286}, {0x36, 0x00001c25},
+	{0x36, 0x00009c25}, {0x36, 0x00011c25},
+	{0x36, 0x00019c25}, {0xb6, 0x00048538},
+	{0x18, 0x00000c07}, {0x5a, 0x0004bd00},
+	{0x19, 0x000739d0}, {0x34, 0x0000adf3},
+	{0x34, 0x00009df0}, {0x34, 0x00008ded},
+	{0x34, 0x00007dea}, {0x34, 0x00006de7},
+	{0x34, 0x000054ee}, {0x34, 0x000044eb},
+	{0x34, 0x000034e8}, {0x34, 0x0000246b},
+	{0x34, 0x00001468}, {0x34, 0x0000006d},
+	{0x00, 0x00030159}, {0x84, 0x00068200},
+	{0x86, 0x000000ce}, {0x87, 0x00048a00},
+	{0x8e, 0x00065540}, {0x8f, 0x00088000},
+	{0xef, 0x000020a0}, {0x3b, 0x000f02b0},
+	{0x3b, 0x000ef7b0}, {0x3b, 0x000d4fb0},
+	{0x3b, 0x000cf060}, {0x3b, 0x000b0090},
+	{0x3b, 0x000a0080}, {0x3b, 0x00090080},
+	{0x3b, 0x0008f780}, {0x3b, 0x000722b0},
+	{0x3b, 0x0006f7b0}, {0x3b, 0x00054fb0},
+	{0x3b, 0x0004f060}, {0x3b, 0x00030090},
+	{0x3b, 0x00020080}, {0x3b, 0x00010080},
+	{0x3b, 0x0000f780}, {0xef, 0x000000a0},
+	{0x00, 0x00010159}, {0x18, 0x0000f407},
+	{0xFE, 0x00000000}, {0xFE, 0x00000000},
+	{0x1F, 0x00080003}, {0xFE, 0x00000000},
+	{0xFE, 0x00000000}, {0x1E, 0x00000001},
+	{0x1F, 0x00080000}, {0x00, 0x00033e60},
+	{0xff, 0xffffffff}
+};
+
+static int rtl8188eu_identify_chip(struct rtl8xxxu_priv *priv)
+{
+	struct device *dev = &priv->udev->dev;
+	u32 sys_cfg, vendor;
+	int ret = 0;
+
+	strscpy(priv->chip_name, "8188EU", sizeof(priv->chip_name));
+	priv->rtl_chip = RTL8188E;
+	priv->rf_paths = 1;
+	priv->rx_paths = 1;
+	priv->tx_paths = 1;
+	priv->has_wifi = 1;
+
+	sys_cfg = rtl8xxxu_read32(priv, REG_SYS_CFG);
+	priv->chip_cut = u32_get_bits(sys_cfg, SYS_CFG_CHIP_VERSION_MASK);
+	if (sys_cfg & SYS_CFG_TRP_VAUX_EN) {
+		dev_info(dev, "Unsupported test chip\n");
+		return -EOPNOTSUPP;
+	}
+
+	/*
+	 * TODO: At a glance, I cut requires a different firmware,
+	 * different initialisation tables, and no software rate
+	 * control. The vendor driver is not configured to handle
+	 * I cut chips by default. Are there any in the wild?
+	 */
+	if (priv->chip_cut == 8) {
+		dev_info(dev, "RTL8188EU cut I is not supported. Please complain about it at linux-wireless@vger.kernel.org.\n");
+		return -EOPNOTSUPP;
+	}
+
+	vendor = sys_cfg & SYS_CFG_VENDOR_ID;
+	rtl8xxxu_identify_vendor_1bit(priv, vendor);
+
+	ret = rtl8xxxu_config_endpoints_no_sie(priv);
+
+	return ret;
+}
+
+static void rtl8188eu_config_channel(struct ieee80211_hw *hw)
+{
+	struct rtl8xxxu_priv *priv = hw->priv;
+	u32 val32, rsr;
+	u8 opmode;
+	int sec_ch_above, channel;
+	int i;
+
+	opmode = rtl8xxxu_read8(priv, REG_BW_OPMODE);
+	rsr = rtl8xxxu_read32(priv, REG_RESPONSE_RATE_SET);
+	channel = hw->conf.chandef.chan->hw_value;
+
+	switch (hw->conf.chandef.width) {
+	case NL80211_CHAN_WIDTH_20_NOHT:
+	case NL80211_CHAN_WIDTH_20:
+		opmode |= BW_OPMODE_20MHZ;
+		rtl8xxxu_write8(priv, REG_BW_OPMODE, opmode);
+
+		val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE);
+		val32 &= ~FPGA_RF_MODE;
+		rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32);
+
+		val32 = rtl8xxxu_read32(priv, REG_FPGA1_RF_MODE);
+		val32 &= ~FPGA_RF_MODE;
+		rtl8xxxu_write32(priv, REG_FPGA1_RF_MODE, val32);
+		break;
+	case NL80211_CHAN_WIDTH_40:
+		if (hw->conf.chandef.center_freq1 >
+		    hw->conf.chandef.chan->center_freq) {
+			sec_ch_above = 1;
+			channel += 2;
+		} else {
+			sec_ch_above = 0;
+			channel -= 2;
+		}
+
+		opmode &= ~BW_OPMODE_20MHZ;
+		rtl8xxxu_write8(priv, REG_BW_OPMODE, opmode);
+		rsr &= ~RSR_RSC_BANDWIDTH_40M;
+		if (sec_ch_above)
+			rsr |= RSR_RSC_LOWER_SUB_CHANNEL;
+		else
+			rsr |= RSR_RSC_UPPER_SUB_CHANNEL;
+		rtl8xxxu_write32(priv, REG_RESPONSE_RATE_SET, rsr);
+
+		val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE);
+		val32 |= FPGA_RF_MODE;
+		rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32);
+
+		val32 = rtl8xxxu_read32(priv, REG_FPGA1_RF_MODE);
+		val32 |= FPGA_RF_MODE;
+		rtl8xxxu_write32(priv, REG_FPGA1_RF_MODE, val32);
+
+		/*
+		 * Set Control channel to upper or lower. These settings
+		 * are required only for 40MHz
+		 */
+		val32 = rtl8xxxu_read32(priv, REG_CCK0_SYSTEM);
+		val32 &= ~CCK0_SIDEBAND;
+		if (!sec_ch_above)
+			val32 |= CCK0_SIDEBAND;
+		rtl8xxxu_write32(priv, REG_CCK0_SYSTEM, val32);
+
+		val32 = rtl8xxxu_read32(priv, REG_OFDM1_LSTF);
+		val32 &= ~OFDM_LSTF_PRIME_CH_MASK; /* 0xc00 */
+		if (sec_ch_above)
+			val32 |= OFDM_LSTF_PRIME_CH_LOW;
+		else
+			val32 |= OFDM_LSTF_PRIME_CH_HIGH;
+		rtl8xxxu_write32(priv, REG_OFDM1_LSTF, val32);
+
+		val32 = rtl8xxxu_read32(priv, REG_FPGA0_POWER_SAVE);
+		val32 &= ~(FPGA0_PS_LOWER_CHANNEL | FPGA0_PS_UPPER_CHANNEL);
+		if (sec_ch_above)
+			val32 |= FPGA0_PS_UPPER_CHANNEL;
+		else
+			val32 |= FPGA0_PS_LOWER_CHANNEL;
+		rtl8xxxu_write32(priv, REG_FPGA0_POWER_SAVE, val32);
+		break;
+
+	default:
+		break;
+	}
+
+	for (i = RF_A; i < priv->rf_paths; i++) {
+		val32 = rtl8xxxu_read_rfreg(priv, i, RF6052_REG_MODE_AG);
+		u32p_replace_bits(&val32, channel, MODE_AG_CHANNEL_MASK);
+		rtl8xxxu_write_rfreg(priv, i, RF6052_REG_MODE_AG, val32);
+	}
+
+	for (i = RF_A; i < priv->rf_paths; i++) {
+		val32 = rtl8xxxu_read_rfreg(priv, i, RF6052_REG_MODE_AG);
+		val32 &= ~MODE_AG_BW_MASK;
+		if (hw->conf.chandef.width == NL80211_CHAN_WIDTH_40)
+			val32 |= MODE_AG_BW_40MHZ_8723B;
+		else
+			val32 |= MODE_AG_BW_20MHZ_8723B;
+		rtl8xxxu_write_rfreg(priv, i, RF6052_REG_MODE_AG, val32);
+	}
+}
+
+static void rtl8188eu_init_aggregation(struct rtl8xxxu_priv *priv)
+{
+	u8 agg_ctrl, usb_spec;
+
+	usb_spec = rtl8xxxu_read8(priv, REG_USB_SPECIAL_OPTION);
+	usb_spec &= ~USB_SPEC_USB_AGG_ENABLE;
+	rtl8xxxu_write8(priv, REG_USB_SPECIAL_OPTION, usb_spec);
+
+	agg_ctrl = rtl8xxxu_read8(priv, REG_TRXDMA_CTRL);
+	agg_ctrl &= ~TRXDMA_CTRL_RXDMA_AGG_EN;
+	rtl8xxxu_write8(priv, REG_TRXDMA_CTRL, agg_ctrl);
+}
+
+static int rtl8188eu_parse_efuse(struct rtl8xxxu_priv *priv)
+{
+	struct rtl8188eu_efuse *efuse = &priv->efuse_wifi.efuse8188eu;
+
+	if (efuse->rtl_id != cpu_to_le16(0x8129))
+		return -EINVAL;
+
+	ether_addr_copy(priv->mac_addr, efuse->mac_addr);
+
+	memcpy(priv->cck_tx_power_index_A, efuse->tx_power_index_A.cck_base,
+	       sizeof(efuse->tx_power_index_A.cck_base));
+
+	memcpy(priv->ht40_1s_tx_power_index_A,
+	       efuse->tx_power_index_A.ht40_base,
+	       sizeof(efuse->tx_power_index_A.ht40_base));
+
+	priv->default_crystal_cap = efuse->xtal_k & 0x3f;
+
+	dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name);
+	dev_info(&priv->udev->dev, "Product: %.11s\n", efuse->device_name);
+	dev_info(&priv->udev->dev, "Serial: %.11s\n", efuse->serial);
+
+	return 0;
+}
+
+static void rtl8188eu_reset_8051(struct rtl8xxxu_priv *priv)
+{
+	u16 sys_func;
+
+	sys_func = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+	sys_func &= ~SYS_FUNC_CPU_ENABLE;
+	rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
+
+	sys_func |= SYS_FUNC_CPU_ENABLE;
+	rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
+}
+
+static int rtl8188eu_load_firmware(struct rtl8xxxu_priv *priv)
+{
+	const char *fw_name;
+	int ret;
+
+	fw_name = "rtlwifi/rtl8188eufw.bin";
+
+	ret = rtl8xxxu_load_firmware(priv, fw_name);
+
+	return ret;
+}
+
+static void rtl8188eu_init_phy_bb(struct rtl8xxxu_priv *priv)
+{
+	u8 val8;
+	u16 val16;
+
+	val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+	val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB | SYS_FUNC_DIO_RF;
+	rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
+
+	/*
+	 * Per vendor driver, run power sequence before init of RF
+	 */
+	val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB;
+	rtl8xxxu_write8(priv, REG_RF_CTRL, val8);
+
+	val8 = SYS_FUNC_USBA | SYS_FUNC_USBD |
+	       SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB;
+	rtl8xxxu_write8(priv, REG_SYS_FUNC, val8);
+
+	rtl8xxxu_init_phy_regs(priv, rtl8188eu_phy_init_table);
+	rtl8xxxu_init_phy_regs(priv, rtl8188e_agc_table);
+}
+
+static int rtl8188eu_init_phy_rf(struct rtl8xxxu_priv *priv)
+{
+	return rtl8xxxu_init_phy_rf(priv, rtl8188eu_radioa_init_table, RF_A);
+}
+
+static int rtl8188eu_iqk_path_a(struct rtl8xxxu_priv *priv)
+{
+	u32 reg_eac, reg_e94, reg_e9c;
+	int result = 0;
+
+	/* Path A IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x10008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x30008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x8214032a);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28160000);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(10);
+
+	/* Check failed */
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
+	reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
+
+	if (!(reg_eac & BIT(28)) &&
+	    ((reg_e94 & 0x03ff0000) != 0x01420000) &&
+	    ((reg_e9c & 0x03ff0000) != 0x00420000))
+		result |= 0x01;
+
+	return result;
+}
+
+static int rtl8188eu_rx_iqk_path_a(struct rtl8xxxu_priv *priv)
+{
+	u32 reg_ea4, reg_eac, reg_e94, reg_e9c, val32;
+	int result = 0;
+
+	/* Leave IQK mode */
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+	u32p_replace_bits(&val32, 0, 0xffffff00);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+	/* Enable path A PA in TX IQK mode */
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, 0x800a0);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0000f);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf117b);
+
+	/* Enter IQK mode */
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+	u32p_replace_bits(&val32, 0x808000, 0xffffff00);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+	/* TX IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+	rtl8xxxu_write32(priv, REG_RX_IQK, 0x81004800);
+
+	/* path-A IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x10008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x30008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160804);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28160000);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(10);
+
+	/* Check failed */
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
+	reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
+
+	if (!(reg_eac & BIT(28)) &&
+	    ((reg_e94 & 0x03ff0000) != 0x01420000) &&
+	    ((reg_e9c & 0x03ff0000) != 0x00420000))
+		result |= 0x01;
+	else
+		goto out;
+
+	val32 = 0x80007c00 |
+		(reg_e94 & 0x03ff0000) | ((reg_e9c >> 16) & 0x03ff);
+	rtl8xxxu_write32(priv, REG_TX_IQK, val32);
+
+	/* Modify RX IQK mode table */
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+	u32p_replace_bits(&val32, 0, 0xffffff00);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, 0x800a0);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0000f);
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7ffa);
+
+	/* Enter IQK mode */
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+	u32p_replace_bits(&val32, 0x808000, 0xffffff00);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+	/* IQK setting */
+	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+	/* Path A IQK setting */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x30008c1c);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x10008c1c);
+
+	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160c05);
+	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28160c05);
+
+	/* LO calibration setting */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
+
+	/* One shot, path A LOK & IQK */
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
+	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+	mdelay(10);
+
+	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+	reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2);
+
+	if (!(reg_eac & BIT(27)) &&
+	    ((reg_ea4 & 0x03ff0000) != 0x01320000) &&
+	    ((reg_eac & 0x03ff0000) != 0x00360000))
+		result |= 0x02;
+	else
+		dev_warn(&priv->udev->dev, "%s: Path A RX IQK failed!\n",
+			 __func__);
+
+out:
+	return result;
+}
+
+static void rtl8188eu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
+				      int result[][8], int t)
+{
+	struct device *dev = &priv->udev->dev;
+	u32 i, val32;
+	int path_a_ok;
+	int retry = 2;
+	static const u32 adda_regs[RTL8XXXU_ADDA_REGS] = {
+		REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH,
+		REG_RX_WAIT_CCA, REG_TX_CCK_RFON,
+		REG_TX_CCK_BBON, REG_TX_OFDM_RFON,
+		REG_TX_OFDM_BBON, REG_TX_TO_RX,
+		REG_TX_TO_TX, REG_RX_CCK,
+		REG_RX_OFDM, REG_RX_WAIT_RIFS,
+		REG_RX_TO_RX, REG_STANDBY,
+		REG_SLEEP, REG_PMPD_ANAEN
+	};
+	static const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = {
+		REG_TXPAUSE, REG_BEACON_CTRL,
+		REG_BEACON_CTRL_1, REG_GPIO_MUXCFG
+	};
+	static const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = {
+		REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR,
+		REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B,
+		REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE,
+		REG_FPGA0_XB_RF_INT_OE, REG_CCK0_AFE_SETTING
+	};
+
+	/*
+	 * Note: IQ calibration must be performed after loading
+	 *       PHY_REG.txt , and radio_a, radio_b.txt
+	 */
+
+	if (t == 0) {
+		/* Save ADDA parameters, turn Path A ADDA on */
+		rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup,
+				   RTL8XXXU_ADDA_REGS);
+		rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
+		rtl8xxxu_save_regs(priv, iqk_bb_regs,
+				   priv->bb_backup, RTL8XXXU_BB_REGS);
+	}
+
+	rtl8xxxu_path_adda_on(priv, adda_regs, true);
+
+	if (t == 0) {
+		val32 = rtl8xxxu_read32(priv, REG_FPGA0_XA_HSSI_PARM1);
+		priv->pi_enabled = u32_get_bits(val32, FPGA0_HSSI_PARM1_PI);
+	}
+
+	if (!priv->pi_enabled) {
+		/* Switch BB to PI mode to do IQ Calibration. */
+		rtl8xxxu_write32(priv, REG_FPGA0_XA_HSSI_PARM1, 0x01000100);
+		rtl8xxxu_write32(priv, REG_FPGA0_XB_HSSI_PARM1, 0x01000100);
+	}
+
+	/* MAC settings */
+	rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup);
+
+	val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING);
+	u32p_replace_bits(&val32, 0xf, 0x0f000000);
+	rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32);
+
+	rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600);
+	rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4);
+	rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000);
+
+	if (!priv->no_pape) {
+		val32 = rtl8xxxu_read32(priv, REG_FPGA0_XAB_RF_SW_CTRL);
+		val32 |= (FPGA0_RF_PAPE |
+			  (FPGA0_RF_PAPE << FPGA0_RF_BD_CTRL_SHIFT));
+		rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32);
+	}
+
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_XA_RF_INT_OE);
+	val32 &= ~BIT(10);
+	rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, val32);
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_XB_RF_INT_OE);
+	val32 &= ~BIT(10);
+	rtl8xxxu_write32(priv, REG_FPGA0_XB_RF_INT_OE, val32);
+
+	/* Page B init */
+	rtl8xxxu_write32(priv, REG_CONFIG_ANT_A, 0x0f600000);
+
+	/* IQ calibration setting */
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+	u32p_replace_bits(&val32, 0x808000, 0xffffff00);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+	rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+	rtl8xxxu_write32(priv, REG_RX_IQK, 0x81004800);
+
+	for (i = 0; i < retry; i++) {
+		path_a_ok = rtl8188eu_iqk_path_a(priv);
+		if (path_a_ok == 0x01) {
+			val32 = rtl8xxxu_read32(priv,
+						REG_TX_POWER_BEFORE_IQK_A);
+			result[t][0] = (val32 >> 16) & 0x3ff;
+			val32 = rtl8xxxu_read32(priv,
+						REG_TX_POWER_AFTER_IQK_A);
+			result[t][1] = (val32 >> 16) & 0x3ff;
+			break;
+		}
+	}
+
+	if (!path_a_ok)
+		dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__);
+
+	for (i = 0; i < retry; i++) {
+		path_a_ok = rtl8188eu_rx_iqk_path_a(priv);
+		if (path_a_ok == 0x03) {
+			val32 = rtl8xxxu_read32(priv,
+						REG_RX_POWER_BEFORE_IQK_A_2);
+			result[t][2] = (val32 >> 16) & 0x3ff;
+			val32 = rtl8xxxu_read32(priv,
+						REG_RX_POWER_AFTER_IQK_A_2);
+			result[t][3] = (val32 >> 16) & 0x3ff;
+
+			break;
+		}
+	}
+
+	if (!path_a_ok)
+		dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__);
+
+	/* Back to BB mode, load original value */
+	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+	u32p_replace_bits(&val32, 0, 0xffffff00);
+	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+	if (t == 0)
+		return;
+
+	if (!priv->pi_enabled) {
+		/* Switch back BB to SI mode after finishing IQ Calibration */
+		rtl8xxxu_write32(priv, REG_FPGA0_XA_HSSI_PARM1, 0x01000000);
+		rtl8xxxu_write32(priv, REG_FPGA0_XB_HSSI_PARM1, 0x01000000);
+	}
+
+	/* Reload ADDA power saving parameters */
+	rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup,
+			      RTL8XXXU_ADDA_REGS);
+
+	/* Reload MAC parameters */
+	rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
+
+	/* Reload BB parameters */
+	rtl8xxxu_restore_regs(priv, iqk_bb_regs,
+			      priv->bb_backup, RTL8XXXU_BB_REGS);
+
+	/* Restore RX initial gain */
+	rtl8xxxu_write32(priv, REG_FPGA0_XA_LSSI_PARM, 0x00032ed3);
+
+	/* Load 0xe30 IQC default value */
+	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00);
+	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00);
+}
+
+static void rtl8188eu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
+{
+	struct device *dev = &priv->udev->dev;
+	int result[4][8];	/* last is final result */
+	int i, candidate;
+	bool path_a_ok;
+	u32 reg_e94, reg_e9c, reg_ea4, reg_eac;
+	u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc;
+	bool simu;
+
+	memset(result, 0, sizeof(result));
+	result[3][0] = 0x100;
+	result[3][2] = 0x100;
+	result[3][4] = 0x100;
+	result[3][6] = 0x100;
+
+	candidate = -1;
+
+	path_a_ok = false;
+
+	for (i = 0; i < 3; i++) {
+		rtl8188eu_phy_iqcalibrate(priv, result, i);
+
+		if (i == 1) {
+			simu = rtl8xxxu_simularity_compare(priv,
+							   result, 0, 1);
+			if (simu) {
+				candidate = 0;
+				break;
+			}
+		}
+
+		if (i == 2) {
+			simu = rtl8xxxu_simularity_compare(priv,
+							   result, 0, 2);
+			if (simu) {
+				candidate = 0;
+				break;
+			}
+
+			simu = rtl8xxxu_simularity_compare(priv,
+							   result, 1, 2);
+			if (simu)
+				candidate = 1;
+			else
+				candidate = 3;
+		}
+	}
+
+	if (candidate >= 0) {
+		reg_e94 = result[candidate][0];
+		priv->rege94 =  reg_e94;
+		reg_e9c = result[candidate][1];
+		priv->rege9c = reg_e9c;
+		reg_ea4 = result[candidate][2];
+		reg_eac = result[candidate][3];
+		reg_eb4 = result[candidate][4];
+		priv->regeb4 = reg_eb4;
+		reg_ebc = result[candidate][5];
+		priv->regebc = reg_ebc;
+		reg_ec4 = result[candidate][6];
+		reg_ecc = result[candidate][7];
+		dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate);
+		dev_dbg(dev,
+			"%s: e94=%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x ecc=%x\n",
+			__func__, reg_e94, reg_e9c, reg_ea4, reg_eac,
+			reg_eb4, reg_ebc, reg_ec4, reg_ecc);
+		path_a_ok = true;
+	} else {
+		reg_e94 = 0x100;
+		reg_eb4 = 0x100;
+		priv->rege94 = 0x100;
+		priv->regeb4 = 0x100;
+		reg_e9c = 0x0;
+		reg_ebc = 0x0;
+		priv->rege9c = 0x0;
+		priv->regebc = 0x0;
+	}
+
+	if (reg_e94 && candidate >= 0)
+		rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result,
+					   candidate, (reg_ea4 == 0));
+
+	rtl8xxxu_save_regs(priv, rtl8xxxu_iqk_phy_iq_bb_reg,
+			   priv->bb_recovery_backup, RTL8XXXU_BB_REGS);
+}
+
+static void rtl8188e_disabled_to_emu(struct rtl8xxxu_priv *priv)
+{
+	u16 val16;
+
+	val16 = rtl8xxxu_read16(priv, REG_APS_FSMCO);
+	val16 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE);
+	rtl8xxxu_write16(priv, REG_APS_FSMCO, val16);
+}
+
+static int rtl8188e_emu_to_active(struct rtl8xxxu_priv *priv)
+{
+	u8 val8;
+	u32 val32;
+	u16 val16;
+	int count, ret = 0;
+
+	/* wait till 0x04[17] = 1 power ready*/
+	for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
+		val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+		if (val32 & BIT(17))
+			break;
+
+		udelay(10);
+	}
+
+	if (!count) {
+		ret = -EBUSY;
+		goto exit;
+	}
+
+	/* reset baseband */
+	val8 = rtl8xxxu_read8(priv, REG_SYS_FUNC);
+	val8 &= ~(SYS_FUNC_BBRSTB | SYS_FUNC_BB_GLB_RSTN);
+	rtl8xxxu_write8(priv, REG_SYS_FUNC, val8);
+
+	/*0x24[23] = 2b'01 schmit trigger */
+	val32 = rtl8xxxu_read32(priv, REG_AFE_XTAL_CTRL);
+	val32 |= BIT(23);
+	rtl8xxxu_write32(priv, REG_AFE_XTAL_CTRL, val32);
+
+	/* 0x04[15] = 0 disable HWPDN (control by DRV)*/
+	val16 = rtl8xxxu_read16(priv, REG_APS_FSMCO);
+	val16 &= ~APS_FSMCO_HW_POWERDOWN;
+	rtl8xxxu_write16(priv, REG_APS_FSMCO, val16);
+
+	/*0x04[12:11] = 2b'00 disable WL suspend*/
+	val16 = rtl8xxxu_read16(priv, REG_APS_FSMCO);
+	val16 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE);
+	rtl8xxxu_write16(priv, REG_APS_FSMCO, val16);
+
+	/* set, then poll until 0 */
+	val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+	val32 |= APS_FSMCO_MAC_ENABLE;
+	rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
+
+	for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
+		val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+		if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) {
+			ret = 0;
+			break;
+		}
+		udelay(10);
+	}
+
+	if (!count) {
+		ret = -EBUSY;
+		goto exit;
+	}
+
+	/* LDO normal mode*/
+	val8 = rtl8xxxu_read8(priv, REG_LPLDO_CTRL);
+	val8 &= ~BIT(4);
+	rtl8xxxu_write8(priv, REG_LPLDO_CTRL, val8);
+
+exit:
+	return ret;
+}
+
+static int rtl8188eu_active_to_emu(struct rtl8xxxu_priv *priv)
+{
+	u8 val8;
+
+	/* Turn off RF */
+	val8 = rtl8xxxu_read8(priv, REG_RF_CTRL);
+	val8 &= ~RF_ENABLE;
+	rtl8xxxu_write8(priv, REG_RF_CTRL, val8);
+
+	/* LDO Sleep mode */
+	val8 = rtl8xxxu_read8(priv, REG_LPLDO_CTRL);
+	val8 |= BIT(4);
+	rtl8xxxu_write8(priv, REG_LPLDO_CTRL, val8);
+
+	return 0;
+}
+
+static int rtl8188eu_emu_to_disabled(struct rtl8xxxu_priv *priv)
+{
+	u32 val32;
+	u16 val16;
+	u8 val8;
+
+	val32 = rtl8xxxu_read32(priv, REG_AFE_XTAL_CTRL);
+	val32 |= BIT(23);
+	rtl8xxxu_write32(priv, REG_AFE_XTAL_CTRL, val32);
+
+	val16 = rtl8xxxu_read16(priv, REG_APS_FSMCO);
+	val16 &= ~APS_FSMCO_PCIE;
+	val16 |= APS_FSMCO_HW_SUSPEND;
+	rtl8xxxu_write16(priv, REG_APS_FSMCO, val16);
+
+	rtl8xxxu_write8(priv, REG_APS_FSMCO + 3, 0x00);
+
+	val8 = rtl8xxxu_read8(priv, REG_GPIO_MUXCFG + 1);
+	val8 &= ~BIT(4);
+	rtl8xxxu_write8(priv, REG_GPIO_MUXCFG + 1, val8);
+
+	/* Set USB suspend enable local register 0xfe10[4]=1 */
+	val8 = rtl8xxxu_read8(priv, 0xfe10);
+	val8 |= BIT(4);
+	rtl8xxxu_write8(priv, 0xfe10, val8);
+
+	return 0;
+}
+
+static int rtl8188eu_active_to_lps(struct rtl8xxxu_priv *priv)
+{
+	struct device *dev = &priv->udev->dev;
+	u8 val8;
+	u16 val16;
+	u32 val32;
+	int retry, retval;
+
+	rtl8xxxu_write8(priv, REG_TXPAUSE, 0x7f);
+
+	retry = 100;
+	retval = -EBUSY;
+	/* Poll 32 bit wide REG_SCH_TX_CMD for 0 to ensure no TX is pending. */
+	do {
+		val32 = rtl8xxxu_read32(priv, REG_SCH_TX_CMD);
+		if (!val32) {
+			retval = 0;
+			break;
+		}
+	} while (retry--);
+
+	if (!retry) {
+		dev_warn(dev, "Failed to flush TX queue\n");
+		retval = -EBUSY;
+		goto out;
+	}
+
+	/* Disable CCK and OFDM, clock gated */
+	val8 = rtl8xxxu_read8(priv, REG_SYS_FUNC);
+	val8 &= ~SYS_FUNC_BBRSTB;
+	rtl8xxxu_write8(priv, REG_SYS_FUNC, val8);
+
+	udelay(2);
+
+	/* Reset MAC TRX */
+	val16 = rtl8xxxu_read16(priv, REG_CR);
+	val16 |= 0xff;
+	val16 &= ~(CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE | CR_SECURITY_ENABLE);
+	rtl8xxxu_write16(priv, REG_CR, val16);
+
+	val8 = rtl8xxxu_read8(priv, REG_DUAL_TSF_RST);
+	val8 |= DUAL_TSF_TX_OK;
+	rtl8xxxu_write8(priv, REG_DUAL_TSF_RST, val8);
+
+out:
+	return retval;
+}
+
+static int rtl8188eu_power_on(struct rtl8xxxu_priv *priv)
+{
+	u16 val16;
+	int ret;
+
+	rtl8188e_disabled_to_emu(priv);
+
+	ret = rtl8188e_emu_to_active(priv);
+	if (ret)
+		goto exit;
+
+	/*
+	 * Enable MAC DMA/WMAC/SCHEDULE/SEC block
+	 * Set CR bit10 to enable 32k calibration.
+	 * We do not set CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE here
+	 * due to a hardware bug in the 88E, requiring those to be
+	 * set after REG_TRXFF_BNDY is set. If not the RXFF bundary
+	 * will get set to a larger buffer size than the real buffer
+	 * size.
+	 */
+	val16 = (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE |
+		 CR_TXDMA_ENABLE | CR_RXDMA_ENABLE |
+		 CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE |
+		 CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE);
+	rtl8xxxu_write16(priv, REG_CR, val16);
+
+exit:
+	return ret;
+}
+
+static void rtl8188eu_power_off(struct rtl8xxxu_priv *priv)
+{
+	u8 val8;
+	u16 val16;
+
+	rtl8xxxu_flush_fifo(priv);
+
+	val8 = rtl8xxxu_read8(priv, REG_TX_REPORT_CTRL);
+	val8 &= ~TX_REPORT_CTRL_TIMER_ENABLE;
+	rtl8xxxu_write8(priv, REG_TX_REPORT_CTRL, val8);
+
+	/* Turn off RF */
+	rtl8xxxu_write8(priv, REG_RF_CTRL, 0x00);
+
+	rtl8188eu_active_to_lps(priv);
+
+	/* Reset Firmware if running in RAM */
+	if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL)
+		rtl8xxxu_firmware_self_reset(priv);
+
+	/* Reset MCU */
+	val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+	val16 &= ~SYS_FUNC_CPU_ENABLE;
+	rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
+
+	/* Reset MCU ready status */
+	rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00);
+
+	/* 32K_CTRL looks to be very 8188e specific */
+	val8 = rtl8xxxu_read8(priv, REG_32K_CTRL);
+	val8 &= ~BIT(0);
+	rtl8xxxu_write8(priv, REG_32K_CTRL, val8);
+
+	rtl8188eu_active_to_emu(priv);
+	rtl8188eu_emu_to_disabled(priv);
+
+	/* Reset MCU IO Wrapper */
+	val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
+	val8 &= ~BIT(3);
+	rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
+
+	val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
+	val8 |= BIT(3);
+	rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
+
+	/* Vendor driver refers to GPIO_IN */
+	val8 = rtl8xxxu_read8(priv, REG_GPIO_PIN_CTRL);
+	/* Vendor driver refers to GPIO_OUT */
+	rtl8xxxu_write8(priv, REG_GPIO_PIN_CTRL + 1, val8);
+	rtl8xxxu_write8(priv, REG_GPIO_PIN_CTRL + 2, 0xff);
+
+	val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL);
+	rtl8xxxu_write8(priv, REG_GPIO_IO_SEL, val8 << 4);
+	val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL + 1);
+	rtl8xxxu_write8(priv, REG_GPIO_IO_SEL + 1, val8 | 0x0f);
+
+	/*
+	 * Set LNA, TRSW, EX_PA Pin to output mode
+	 * Referred to as REG_BB_PAD_CTRL in 8188eu vendor driver
+	 */
+	rtl8xxxu_write32(priv, REG_PAD_CTRL1, 0x00080808);
+
+	rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x00);
+
+	rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, 0x00000000);
+}
+
+static void rtl8188e_enable_rf(struct rtl8xxxu_priv *priv)
+{
+	u32 val32;
+
+	rtl8xxxu_write8(priv, REG_RF_CTRL, RF_ENABLE | RF_RSTB | RF_SDMRSTB);
+
+	val32 = rtl8xxxu_read32(priv, REG_OFDM0_TRX_PATH_ENABLE);
+	val32 &= ~(OFDM_RF_PATH_RX_MASK | OFDM_RF_PATH_TX_MASK);
+	val32 |= OFDM_RF_PATH_RX_A | OFDM_RF_PATH_TX_A;
+	rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, val32);
+
+	rtl8xxxu_write8(priv, REG_TXPAUSE, 0x00);
+}
+
+static void rtl8188e_disable_rf(struct rtl8xxxu_priv *priv)
+{
+	u32 val32;
+
+	val32 = rtl8xxxu_read32(priv, REG_OFDM0_TRX_PATH_ENABLE);
+	val32 &= ~OFDM_RF_PATH_TX_MASK;
+	rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, val32);
+
+	/* Power down RF module */
+	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0);
+
+	rtl8188eu_active_to_emu(priv);
+}
+
+static void rtl8188e_usb_quirks(struct rtl8xxxu_priv *priv)
+{
+	u16 val16;
+
+	/*
+	 * Technically this is not a USB quirk, but a chip quirk.
+	 * This has to be done after REG_TRXFF_BNDY is set, see
+	 * rtl8188eu_power_on() for details.
+	 */
+	val16 = rtl8xxxu_read16(priv, REG_CR);
+	val16 |= (CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE);
+	rtl8xxxu_write16(priv, REG_CR, val16);
+
+	rtl8xxxu_gen2_usb_quirks(priv);
+
+	/* Pre-TX enable WEP/TKIP security */
+	rtl8xxxu_write8(priv, REG_EARLY_MODE_CONTROL_8188E + 3, 0x01);
+}
+
+static s8 rtl8188e_cck_rssi(struct rtl8xxxu_priv *priv, u8 cck_agc_rpt)
+{
+	/* only use lna 0/1/2/3/7 */
+	static const s8 lna_gain_table_0[8] = {17, -1, -13, -29, -32, -35, -38, -41};
+	/* only use lna 3/7 */
+	static const s8 lna_gain_table_1[8] = {29, 20, 12, 3, -6, -15, -24, -33};
+
+	s8 rx_pwr_all = 0x00;
+	u8 vga_idx, lna_idx;
+	s8 lna_gain = 0;
+
+	lna_idx = u8_get_bits(cck_agc_rpt, CCK_AGC_RPT_LNA_IDX_MASK);
+	vga_idx = u8_get_bits(cck_agc_rpt, CCK_AGC_RPT_VGA_IDX_MASK);
+
+	if (priv->chip_cut >= 8) /* cut I */ /* SMIC */
+		lna_gain = lna_gain_table_0[lna_idx];
+	else /* TSMC */
+		lna_gain = lna_gain_table_1[lna_idx];
+
+	rx_pwr_all = lna_gain - (2 * vga_idx);
+
+	return rx_pwr_all;
+}
+
+struct rtl8xxxu_fileops rtl8188eu_fops = {
+	.identify_chip = rtl8188eu_identify_chip,
+	.parse_efuse = rtl8188eu_parse_efuse,
+	.load_firmware = rtl8188eu_load_firmware,
+	.power_on = rtl8188eu_power_on,
+	.power_off = rtl8188eu_power_off,
+	.reset_8051 = rtl8188eu_reset_8051,
+	.llt_init = rtl8xxxu_init_llt_table,
+	.init_phy_bb = rtl8188eu_init_phy_bb,
+	.init_phy_rf = rtl8188eu_init_phy_rf,
+	.phy_lc_calibrate = rtl8723a_phy_lc_calibrate,
+	.phy_iq_calibrate = rtl8188eu_phy_iq_calibrate,
+	.config_channel = rtl8188eu_config_channel,
+	.parse_rx_desc = rtl8xxxu_parse_rxdesc16,
+	.init_aggregation = rtl8188eu_init_aggregation,
+	.enable_rf = rtl8188e_enable_rf,
+	.disable_rf = rtl8188e_disable_rf,
+	.usb_quirks = rtl8188e_usb_quirks,
+	.set_tx_power = rtl8188f_set_tx_power,
+	.update_rate_mask = rtl8xxxu_gen2_update_rate_mask,
+	.report_connect = rtl8xxxu_gen2_report_connect,
+	.fill_txdesc = rtl8xxxu_fill_txdesc_v3,
+	.set_crystal_cap = rtl8188f_set_crystal_cap,
+	.cck_rssi = rtl8188e_cck_rssi,
+	.writeN_block_size = 128,
+	.rx_desc_size = sizeof(struct rtl8xxxu_rxdesc16),
+	.tx_desc_size = sizeof(struct rtl8xxxu_txdesc32),
+	.has_tx_report = 1,
+	.gen2_thermal_meter = 1,
+	.adda_1t_init = 0x0b1b25a0,
+	.adda_1t_path_on = 0x0bdb25a0,
+	/*
+	 * Use 9K for 8188e normal chip
+	 * Max RX buffer = 10K - max(TxReportSize(64*8), WOLPattern(16*24))
+	 */
+	.trxff_boundary = 0x25ff,
+	.pbp_rx = PBP_PAGE_SIZE_128,
+	.pbp_tx = PBP_PAGE_SIZE_128,
+	.mactable = rtl8188e_mac_init_table,
+	.total_page_num = TX_TOTAL_PAGE_NUM_8188E,
+	.page_num_hi = TX_PAGE_NUM_HI_PQ_8188E,
+	.page_num_lo = TX_PAGE_NUM_LO_PQ_8188E,
+	.page_num_norm = TX_PAGE_NUM_NORM_PQ_8188E,
+	.last_llt_entry = 175,
+};
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8188f.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8188f.c
index 54e136c964b4..63484ab1b4d7 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8188f.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8188f.c
@@ -370,7 +370,7 @@ static void rtl8188f_channel_to_group(int channel, int *group, int *cck_group)
 		*cck_group = *group;
 }
 
-static void
+void
 rtl8188f_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40)
 {
 	u32 val32, ofdm, mcs;
@@ -1651,7 +1651,7 @@ static void rtl8188f_usb_quirks(struct rtl8xxxu_priv *priv)
 #define XTAL1	GENMASK(22, 17)
 #define XTAL0	GENMASK(16, 11)
 
-static void rtl8188f_set_crystal_cap(struct rtl8xxxu_priv *priv, u8 crystal_cap)
+void rtl8188f_set_crystal_cap(struct rtl8xxxu_priv *priv, u8 crystal_cap)
 {
 	struct rtl8xxxu_cfo_tracking *cfo = &priv->cfo_tracking;
 	u32 val32;
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
index 7aa00442c3a5..c63d3459d8d2 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
@@ -46,6 +46,7 @@ MODULE_LICENSE("GPL");
 MODULE_FIRMWARE("rtlwifi/rtl8723aufw_A.bin");
 MODULE_FIRMWARE("rtlwifi/rtl8723aufw_B.bin");
 MODULE_FIRMWARE("rtlwifi/rtl8723aufw_B_NoBT.bin");
+MODULE_FIRMWARE("rtlwifi/rtl8188eufw.bin");
 MODULE_FIRMWARE("rtlwifi/rtl8192cufw_A.bin");
 MODULE_FIRMWARE("rtlwifi/rtl8192cufw_B.bin");
 MODULE_FIRMWARE("rtlwifi/rtl8192cufw_TMSC.bin");
@@ -2010,6 +2011,7 @@ int rtl8xxxu_load_firmware(struct rtl8xxxu_priv *priv, const char *fw_name)
 	switch (signature & 0xfff0) {
 	case 0x92e0:
 	case 0x92c0:
+	case 0x88e0:
 	case 0x88c0:
 	case 0x5300:
 	case 0x2300:
@@ -2081,10 +2083,20 @@ rtl8xxxu_init_mac(struct rtl8xxxu_priv *priv)
 		}
 	}
 
-	if (priv->rtl_chip != RTL8723B &&
-	    priv->rtl_chip != RTL8192E &&
-	    priv->rtl_chip != RTL8188F)
+	switch (priv->rtl_chip) {
+	case RTL8188C:
+	case RTL8188R:
+	case RTL8191C:
+	case RTL8192C:
+	case RTL8723A:
 		rtl8xxxu_write8(priv, REG_MAX_AGGR_NUM, 0x0a);
+		break;
+	case RTL8188E:
+		rtl8xxxu_write16(priv, REG_MAX_AGGR_NUM, 0x0707);
+		break;
+	default:
+		break;
+	}
 
 	return 0;
 }
@@ -2383,11 +2395,16 @@ static int rtl8xxxu_llt_write(struct rtl8xxxu_priv *priv, u8 address, u8 data)
 int rtl8xxxu_init_llt_table(struct rtl8xxxu_priv *priv)
 {
 	int ret;
-	int i;
+	int i, last_entry;
 	u8 last_tx_page;
 
 	last_tx_page = priv->fops->total_page_num;
 
+	if (priv->fops->last_llt_entry)
+		last_entry = priv->fops->last_llt_entry;
+	else
+		last_entry = 255;
+
 	for (i = 0; i < last_tx_page; i++) {
 		ret = rtl8xxxu_llt_write(priv, i, i + 1);
 		if (ret)
@@ -2399,14 +2416,14 @@ int rtl8xxxu_init_llt_table(struct rtl8xxxu_priv *priv)
 		goto exit;
 
 	/* Mark remaining pages as a ring buffer */
-	for (i = last_tx_page + 1; i < 0xff; i++) {
+	for (i = last_tx_page + 1; i < last_entry; i++) {
 		ret = rtl8xxxu_llt_write(priv, i, (i + 1));
 		if (ret)
 			goto exit;
 	}
 
 	/*  Let last entry point to the start entry of ring buffer */
-	ret = rtl8xxxu_llt_write(priv, 0xff, last_tx_page + 1);
+	ret = rtl8xxxu_llt_write(priv, last_entry, last_tx_page + 1);
 	if (ret)
 		goto exit;
 
@@ -2714,8 +2731,8 @@ void rtl8xxxu_fill_iqk_matrix_b(struct rtl8xxxu_priv *priv, bool iqk_ok,
 
 #define MAX_TOLERANCE		5
 
-static bool rtl8xxxu_simularity_compare(struct rtl8xxxu_priv *priv,
-					int result[][8], int c1, int c2)
+bool rtl8xxxu_simularity_compare(struct rtl8xxxu_priv *priv,
+				 int result[][8], int c1, int c2)
 {
 	u32 i, j, diff, simubitmap, bound = 0;
 	int candidate[2] = {-1, -1};	/* for path A and path B */
@@ -3908,7 +3925,8 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 		goto exit;
 
 	/* RFSW Control - clear bit 14 ?? */
-	if (priv->rtl_chip != RTL8723B && priv->rtl_chip != RTL8192E)
+	if (priv->rtl_chip != RTL8723B && priv->rtl_chip != RTL8192E &&
+	    priv->rtl_chip != RTL8188E)
 		rtl8xxxu_write32(priv, REG_FPGA0_TX_INFO, 0x00000003);
 
 	val32 = FPGA0_RF_TRSW | FPGA0_RF_TRSWB | FPGA0_RF_ANTSW |
@@ -3921,7 +3939,7 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32);
 
 	/* 0x860[6:5]= 00 - why? - this sets antenna B */
-	if (priv->rtl_chip != RTL8192E)
+	if (priv->rtl_chip != RTL8192E && priv->rtl_chip != RTL8188E)
 		rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, 0x66f60210);
 
 	if (!macpower) {
@@ -3989,6 +4007,15 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	} else if (priv->rtl_chip == RTL8188F) {
 		rtl8xxxu_write32(priv, REG_HISR0, 0xffffffff);
 		rtl8xxxu_write32(priv, REG_HISR1, 0xffffffff);
+	} else if (priv->rtl_chip == RTL8188E) {
+		rtl8xxxu_write32(priv, REG_HISR0, 0xffffffff);
+		val32 = IMR0_PSTIMEOUT | IMR0_TBDER | IMR0_CPWM | IMR0_CPWM2;
+		rtl8xxxu_write32(priv, REG_HIMR0, val32);
+		val32 = IMR1_TXERR | IMR1_RXERR | IMR1_TXFOVW | IMR1_RXFOVW;
+		rtl8xxxu_write32(priv, REG_HIMR1, val32);
+		val8 = rtl8xxxu_read8(priv, REG_USB_SPECIAL_OPTION);
+		val8 |= USB_SPEC_INT_BULK_SELECT;
+		rtl8xxxu_write8(priv, REG_USB_SPECIAL_OPTION, val8);
 	} else {
 		/*
 		 * Enable all interrupts - not obvious USB needs to do this
@@ -4094,7 +4121,7 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	if (fops->init_aggregation)
 		fops->init_aggregation(priv);
 
-	if (priv->rtl_chip == RTL8188F) {
+	if (priv->rtl_chip == RTL8188F || priv->rtl_chip == RTL8188E) {
 		rtl8xxxu_write16(priv, REG_PKT_VO_VI_LIFE_TIME, 0x0400); /* unit: 256us. 256ms */
 		rtl8xxxu_write16(priv, REG_PKT_BE_BK_LIFE_TIME, 0x0400); /* unit: 256us. 256ms */
 	}
@@ -4128,7 +4155,7 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 	/* Disable BAR - not sure if this has any effect on USB */
 	rtl8xxxu_write32(priv, REG_BAR_MODE_CTRL, 0x0201ffff);
 
-	if (priv->rtl_chip != RTL8188F)
+	if (priv->rtl_chip != RTL8188F && priv->rtl_chip != RTL8188E)
 		rtl8xxxu_write16(priv, REG_FAST_EDCA_CTRL, 0);
 
 	if (fops->init_statistics)
@@ -4146,9 +4173,9 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 		 * Reset USB mode switch setting
 		 */
 		rtl8xxxu_write8(priv, REG_ACLK_MON, 0x00);
-	} else if (priv->rtl_chip == RTL8188F) {
+	} else if (priv->rtl_chip == RTL8188F || priv->rtl_chip == RTL8188E) {
 		/*
-		 * Init GPIO settings for 8188f
+		 * Init GPIO settings for 8188f, 8188e
 		 */
 		val8 = rtl8xxxu_read8(priv, REG_GPIO_MUXCFG);
 		val8 &= ~GPIO_MUXCFG_IO_SEL_ENBT;
@@ -4194,7 +4221,7 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 			val32 |= FPGA_RF_MODE_CCK;
 			rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32);
 		}
-	} else if (priv->rtl_chip == RTL8192E) {
+	} else if (priv->rtl_chip == RTL8192E || priv->rtl_chip == RTL8188E) {
 		rtl8xxxu_write8(priv, REG_USB_HRPWM, 0x00);
 	}
 
@@ -5079,6 +5106,96 @@ rtl8xxxu_fill_txdesc_v2(struct ieee80211_hw *hw, struct ieee80211_hdr *hdr,
 	}
 }
 
+/*
+ * Fill in v3 (gen1) specific TX descriptor bits.
+ * This format is a hybrid between the v1 and v2 formats, only seen
+ * on 8188eu devices so far.
+ */
+void
+rtl8xxxu_fill_txdesc_v3(struct ieee80211_hw *hw, struct ieee80211_hdr *hdr,
+			struct ieee80211_tx_info *tx_info,
+			struct rtl8xxxu_txdesc32 *tx_desc, bool sgi,
+			bool short_preamble, bool ampdu_enable, u32 rts_rate)
+{
+	struct ieee80211_rate *tx_rate = ieee80211_get_tx_rate(hw, tx_info);
+	struct rtl8xxxu_priv *priv = hw->priv;
+	struct device *dev = &priv->udev->dev;
+	u8 *qc = ieee80211_get_qos_ctl(hdr);
+	u8 tid = qc[0] & IEEE80211_QOS_CTL_TID_MASK;
+	u32 rate;
+	u16 rate_flags = tx_info->control.rates[0].flags;
+	u16 seq_number;
+
+	if (rate_flags & IEEE80211_TX_RC_MCS &&
+	    !ieee80211_is_mgmt(hdr->frame_control))
+		rate = tx_info->control.rates[0].idx + DESC_RATE_MCS0;
+	else
+		rate = tx_rate->hw_value;
+
+	seq_number = IEEE80211_SEQ_TO_SN(le16_to_cpu(hdr->seq_ctrl));
+
+	if (ieee80211_is_data(hdr->frame_control)) {
+		rate = DESC_RATE_MCS7; /* TODO: software rate control */
+		tx_desc->txdw5 = cpu_to_le32(rate);
+		tx_desc->txdw4 |= cpu_to_le32(TXDESC32_USE_DRIVER_RATE);
+		/* Data/RTS rate FB limit */
+		tx_desc->txdw5 |= cpu_to_le32(0x0001ff00);
+	}
+
+	if (rtl8xxxu_debug & RTL8XXXU_DEBUG_TX)
+		dev_info(dev, "%s: TX rate: %d, pkt size %d\n",
+			 __func__, rate, le16_to_cpu(tx_desc->pkt_size));
+
+	tx_desc->txdw3 = cpu_to_le32((u32)seq_number << TXDESC32_SEQ_SHIFT);
+
+	if (ampdu_enable && test_bit(tid, priv->tid_tx_operational))
+		tx_desc->txdw2 |= cpu_to_le32(TXDESC40_AGG_ENABLE);
+	else
+		tx_desc->txdw2 |= cpu_to_le32(TXDESC40_AGG_BREAK);
+
+	if (ieee80211_is_mgmt(hdr->frame_control)) {
+		tx_desc->txdw5 = cpu_to_le32(rate);
+		tx_desc->txdw4 |= cpu_to_le32(TXDESC32_USE_DRIVER_RATE);
+		tx_desc->txdw5 |= cpu_to_le32(6 << TXDESC32_RETRY_LIMIT_SHIFT);
+		tx_desc->txdw5 |= cpu_to_le32(TXDESC32_RETRY_LIMIT_ENABLE);
+	}
+
+	if (ieee80211_is_data_qos(hdr->frame_control)) {
+		tx_desc->txdw4 |= cpu_to_le32(TXDESC32_QOS);
+
+		if (conf_is_ht40(&hw->conf)) {
+			tx_desc->txdw4 |= cpu_to_le32(TXDESC_DATA_BW);
+
+			if (conf_is_ht40_minus(&hw->conf))
+				tx_desc->txdw4 |= cpu_to_le32(TXDESC_PRIME_CH_OFF_UPPER);
+			else
+				tx_desc->txdw4 |= cpu_to_le32(TXDESC_PRIME_CH_OFF_LOWER);
+		}
+	}
+
+	if (short_preamble)
+		tx_desc->txdw4 |= cpu_to_le32(TXDESC32_SHORT_PREAMBLE);
+
+	if (sgi)
+		tx_desc->txdw5 |= cpu_to_le32(TXDESC32_SHORT_GI);
+
+	/*
+	 * rts_rate is zero if RTS/CTS or CTS to SELF are not enabled
+	 */
+	tx_desc->txdw4 |= cpu_to_le32(rts_rate << TXDESC32_RTS_RATE_SHIFT);
+	if (ampdu_enable || (rate_flags & IEEE80211_TX_RC_USE_RTS_CTS)) {
+		tx_desc->txdw4 |= cpu_to_le32(TXDESC32_RTS_CTS_ENABLE);
+		tx_desc->txdw4 |= cpu_to_le32(TXDESC32_HW_RTS_ENABLE);
+	} else if (rate_flags & IEEE80211_TX_RC_USE_CTS_PROTECT) {
+		tx_desc->txdw4 |= cpu_to_le32(TXDESC32_CTS_SELF_ENABLE);
+		tx_desc->txdw4 |= cpu_to_le32(TXDESC32_HW_RTS_ENABLE);
+	}
+
+	tx_desc->txdw2 |= cpu_to_le32(TXDESC_ANTENNA_SELECT_A |
+				      TXDESC_ANTENNA_SELECT_B);
+	tx_desc->txdw7 |= cpu_to_le32(TXDESC_ANTENNA_SELECT_C);
+}
+
 static void rtl8xxxu_tx(struct ieee80211_hw *hw,
 			struct ieee80211_tx_control *control,
 			struct sk_buff *skb)
@@ -6597,7 +6714,10 @@ static int rtl8xxxu_start(struct ieee80211_hw *hw)
 	rtl8xxxu_write16(priv, REG_RXFLTMAP2, 0xffff);
 	rtl8xxxu_write16(priv, REG_RXFLTMAP0, 0xffff);
 
-	rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, 0x6954341e);
+	if (priv->rtl_chip == RTL8188E)
+		rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, 0x6955341e);
+	else
+		rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, 0x6954341e);
 
 	return ret;
 
@@ -6764,6 +6884,7 @@ static int rtl8xxxu_probe(struct usb_interface *interface,
 		case 0x817f:
 		case 0x818b:
 		case 0xf179:
+		case 0x8179:
 			untested = 0;
 			break;
 		}
@@ -6900,8 +7021,10 @@ static int rtl8xxxu_probe(struct usb_interface *interface,
 
 	hw->extra_tx_headroom = priv->fops->tx_desc_size;
 	ieee80211_hw_set(hw, SIGNAL_DBM);
+
 	/*
-	 * The firmware handles rate control
+	 * The firmware handles rate control, except for RTL8188EU,
+	 * where we handle the rate control in the driver.
 	 */
 	ieee80211_hw_set(hw, HAS_RATE_CONTROL);
 	ieee80211_hw_set(hw, SUPPORT_FAST_XMIT);
@@ -6986,6 +7109,50 @@ static const struct usb_device_id dev_table[] = {
 /* RTL8188FU */
 {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0xf179, 0xff, 0xff, 0xff),
 	.driver_info = (unsigned long)&rtl8188fu_fops},
+{USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x8179, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* Tested by Hans de Goede - rtl8188etv */
+{USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x0179, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* Sitecom rtl8188eus */
+{USB_DEVICE_AND_INTERFACE_INFO(0x0df6, 0x0076, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* D-Link USB-GO-N150 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x3311, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* D-Link DWA-125 REV D1 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x330f, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* D-Link DWA-123 REV D1 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x3310, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* D-Link DWA-121 rev B1 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x331b, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* Abocom - Abocom */
+{USB_DEVICE_AND_INTERFACE_INFO(0x07b8, 0x8179, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* Elecom WDC-150SU2M */
+{USB_DEVICE_AND_INTERFACE_INFO(0x056e, 0x4008, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* TP-Link TL-WN722N v2 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2357, 0x010c, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* TP-Link TL-WN727N v5.21 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2357, 0x0111, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* MERCUSYS MW150US v2 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2c4e, 0x0102, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* ASUS USB-N10 Nano B1 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x0b05, 0x18f0, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+ /* Edimax EW-7811Un V2 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x7392, 0xb811, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
+/* Rosewill USB-N150 Nano */
+{USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0xffef, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8188eu_fops},
 #ifdef CONFIG_RTL8XXXU_UNTESTED
 /* Still supported by rtlwifi */
 {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x8176, 0xff, 0xff, 0xff),
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
index 3e79efdfb4c2..5818b2378bab 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
@@ -371,6 +371,11 @@
 #define  PBP_PAGE_SIZE_512		0x3
 #define  PBP_PAGE_SIZE_1024		0x4
 
+/* 8188eu IOL magic */
+#define REG_PKT_BUF_ACCESS_CTRL		0x0106
+#define  PKT_BUF_ACCESS_CTRL_TX		0x69
+#define  PKT_BUF_ACCESS_CTRL_RX		0xa5
+
 #define REG_TRXDMA_CTRL			0x010c
 #define  TRXDMA_CTRL_RXDMA_AGG_EN	BIT(2)
 #define  TRXDMA_CTRL_VOQ_SHIFT		4
@@ -407,6 +412,8 @@
 #define REG_MBIST_START			0x0174
 #define REG_MBIST_DONE			0x0178
 #define REG_MBIST_FAIL			0x017c
+/* 8188EU */
+#define REG_32K_CTRL			0x0194
 #define REG_C2HEVT_MSG_NORMAL		0x01a0
 /* 8192EU/8723BU/8812 */
 #define REG_C2HEVT_CMD_ID_8723B		0x01ae
@@ -942,6 +949,16 @@
 #define REG_FPGA1_RF_MODE		0x0900
 
 #define REG_FPGA1_TX_INFO		0x090c
+#define  FPGA1_TX_ANT_MASK		0x0000000f
+#define  FPGA1_TX_ANT_L_MASK		0x000000f0
+#define  FPGA1_TX_ANT_NON_HT_MASK	0x00000f00
+#define  FPGA1_TX_ANT_HT1_MASK		0x0000f000
+#define  FPGA1_TX_ANT_HT2_MASK		0x000f0000
+#define  FPGA1_TX_ANT_HT_S1_MASK	0x00f00000
+#define  FPGA1_TX_ANT_NON_HT_S1_MASK	0x0f000000
+#define  FPGA1_TX_OFDM_TXSC_MASK	0x30000000
+
+#define REG_ANT_MAPPING1		0x0914
 #define REG_DPDT_CTRL			0x092c	/* 8723BU */
 #define REG_RFE_CTRL_ANTA_SRC		0x0930	/* 8723BU */
 #define REG_RFE_PATH_SELECT		0x0940	/* 8723BU */
@@ -954,9 +971,25 @@
 
 #define REG_CCK0_AFE_SETTING		0x0a04
 #define  CCK0_AFE_RX_MASK		0x0f000000
-#define  CCK0_AFE_RX_ANT_AB		BIT(24)
+#define  CCK0_AFE_TX_MASK		0xf0000000
 #define  CCK0_AFE_RX_ANT_A		0
-#define  CCK0_AFE_RX_ANT_B		(BIT(24) | BIT(26))
+#define  CCK0_AFE_RX_ANT_B		BIT(26)
+#define  CCK0_AFE_RX_ANT_C		BIT(27)
+#define  CCK0_AFE_RX_ANT_D		(BIT(26) | BIT(27))
+#define  CCK0_AFE_RX_ANT_OPTION_A	0
+#define  CCK0_AFE_RX_ANT_OPTION_B	BIT(24)
+#define  CCK0_AFE_RX_ANT_OPTION_C	BIT(25)
+#define  CCK0_AFE_RX_ANT_OPTION_D	(BIT(24) | BIT(25))
+#define  CCK0_AFE_TX_ANT_A		BIT(31)
+#define  CCK0_AFE_TX_ANT_B		BIT(30)
+
+#define REG_CCK_ANTDIV_PARA2		0x0a04
+#define REG_BB_POWER_SAVE4		0x0a74
+
+/* 8188eu */
+#define REG_LNA_SWITCH			0x0b2c
+#define  LNA_SWITCH_DISABLE_CSCG	BIT(22)
+#define  LNA_SWITCH_OUTPUT_CG		BIT(31)
 
 #define REG_CCK_PD_THRESH			0x0a0a
 #define  CCK_PD_TYPE1_LV0_TH		0x40
@@ -1020,6 +1053,9 @@
 
 #define REG_OFDM0_RX_IQ_EXT_ANTA	0x0ca0
 
+/* 8188eu */
+#define REG_ANTDIV_PARA1		0x0ca4
+
 /* 8723bu */
 #define REG_OFDM0_TX_PSDO_NOISE_WEIGHT	0x0ce4
 
