diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
new file mode 100644
index 0000000..000ca20
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -0,0 +1,196 @@
+Samsung GPIO and Pin Mux/Config controller
+
+Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pads/pins
+and also provides ability to multiplex and configure the output of various
+on-chip controllers onto these pads.
+
+Required Properties:
+- compatible: should be one of the following.
+  - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
+
+- reg: Base address of the pin controller hardware module and length of
+  the address space it occupies.
+
+- interrupts: interrupt specifier for the controller. The format and value of
+  the interrupt specifier depends on the interrupt parent for the controller.
+
+- Pin mux/config groups as child nodes: The pin mux (selecting pin function
+  mode) and pin config (pull up/down, driver strength) settings are represented
+  as child nodes of the pin-controller node. There should be atleast one
+  child node and there is no limit on the count of these child nodes.
+
+  The child node should contain a list of pin(s) on which a particular pin
+  function selection or pin configuration (or both) have to applied. This
+  list of pins is specified using the property name "samsung,pins". There
+  should be atleast one pin specfied for this property and there is no upper
+  limit on the count of pins that can be specified. The pins are specified
+  using pin names which are derived from the hardware manual of the SoC. As
+  an example, the pins in GPA0 bank of the pin controller can be represented
+  as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
+  The format of the pin names should be (as per the hardware manual)
+  "[pin bank name]-[pin number within the bank]".
+
+  The pin function selection that should be applied on the pins listed in the
+  child node is specified using the "samsung,pin-function" property. The value
+  of this property that should be applied to each of the pins listed in the
+  "samsung,pins" property should be picked from the hardware manual of the SoC
+  for the specified pin group. This property is optional in the child node if
+  no specific function selection is desired for the pins listed in the child
+  node. The value of this property is used as-is to program the pin-controller
+  function selector register of the pin-bank.
+
+  The child node can also optionally specify one or more of the pin
+  configuration that should be applied on all the pins listed in the
+  "samsung,pins" property of the child node. The following pin configuration
+  properties are supported.
+
+  - samsung,pin-pud: Pull up/down configuration.
+  - samsung,pin-drv: Drive strength configuration.
+  - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
+  - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
+
+  The values specified by these config properties should be derived from the
+  hardware manual and these values are programmed as-is into the pin
+  pull up/down and driver strength register of the pin-controller.
+
+  Note: A child should include atleast a pin function selection property or
+  pin configuration property (one or more) or both.
+
+  The client nodes that require a particular pin function selection and/or
+  pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
+  file.
+
+External GPIO and Wakeup Interrupts:
+
+The controller supports two types of external interrupts over gpio. The first
+is the external gpio interrupt and second is the external wakeup interrupts.
+The difference between the two is that the external wakeup interrupts can be
+used as system wakeup events.
+
+A. External GPIO Interrupts: For supporting external gpio interrupts, the
+   following properties should be specified in the pin-controller device node.
+
+- interrupt-controller: identifies the controller node as interrupt-parent.
+- #interrupt-cells: the value of this property should be 2.
+  - First Cell: represents the external gpio interrupt number local to the
+    external gpio interrupt space of the controller.
+  - Second Cell: flags to identify the type of the interrupt
+    - 1 = rising edge triggered
+    - 2 = falling edge triggered
+    - 3 = rising and falling edge triggered
+    - 4 = high level triggered
+    - 8 = low level triggered
+
+B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
+   child node representing the external wakeup interrupt controller should be
+   included in the pin-controller device node. This child node should include
+   the following properties.
+
+   - compatible: identifies the type of the external wakeup interrupt controller
+     The possible values are:
+     - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos4210 SoC.
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupt-controller: identifies the node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2
+     - First Cell: represents the external wakeup interrupt number local to
+       the external wakeup interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+Aliases:
+
+All the pin controller nodes should be represented in the aliases node using
+the following format 'pinctrl{n}' where n is a unique number for the alias.
+
+Example 1: A pin-controller node with pin groups.
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+Example 2: A pin-controller node with external wakeup interrupt controller node.
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+					<0 32 0>;
+		};
+	};
+
+Example 3: A uart client node that supports 'default' and 'flow-control' states.
+
+	uart@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+		pinctrl-names = "default", "flow-control;
+		pinctrl-0 = <&uart0_data>;
+		pinctrl-1 = <&uart0_data &uart0_fctl>;
+	};
+
+Example 4: Set up the default pin state for uart controller.
+
+	static int s3c24xx_serial_probe(struct platform_device *pdev) {
+		struct pinctrl *pinctrl;
+		...
+		...
+		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+	}
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 73aafd9..b4503cd 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -161,6 +161,11 @@ config PINCTRL_COH901
 	  COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
 	  ports of 8 GPIO pins each.
 
+config PINCTRL_SAMSUNG
+	bool "Samsung pinctrl driver"
+	select PINMUX
+	select PINCONF
+
 source "drivers/pinctrl/spear/Kconfig"
 
 endmenu
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index cda3984..7155301 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -32,5 +32,6 @@ obj-$(CONFIG_PINCTRL_TEGRA20)	+= pinctrl-tegra20.o
 obj-$(CONFIG_PINCTRL_TEGRA30)	+= pinctrl-tegra30.o
 obj-$(CONFIG_PINCTRL_U300)	+= pinctrl-u300.o
 obj-$(CONFIG_PINCTRL_COH901)	+= pinctrl-coh901.o
+obj-$(CONFIG_PINCTRL_SAMSUNG)	+= pinctrl-samsung.o
 
 obj-$(CONFIG_PLAT_SPEAR)	+= spear/
diff --git a/drivers/pinctrl/pinctrl-samsung.c b/drivers/pinctrl/pinctrl-samsung.c
new file mode 100644
index 0000000..8a24223
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-samsung.c
@@ -0,0 +1,888 @@
+/*
+ * pin-controller/pin-mux/pin-config/gpio-driver for Samsung's SoC's.
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2012 Linaro Ltd
+ *		http://www.linaro.org
+ *
+ * Author: Thomas Abraham <thomas.ab@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This driver implements the Samsung pinctrl driver. It supports setting up of
+ * pinmux and pinconf configurations. The gpiolib interface is also included.
+ * External interrupt (gpio and wakeup) support are not included in this driver
+ * but provides extensions to which platform specific implementation of the gpio
+ * and wakeup interrupts can be hooked to.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+
+#include "core.h"
+#include "pinctrl-samsung.h"
+
+#define GROUP_SUFFIX		"-grp"
+#define GSUFFIX_LEN		sizeof(GROUP_SUFFIX)
+#define FUNCTION_SUFFIX		"-mux"
+#define FSUFFIX_LEN		sizeof(FUNCTION_SUFFIX)
+
+/* list of all possible config options supported */
+struct pin_config {
+	char		*prop_cfg;
+	unsigned int	cfg_type;
+} pcfgs[] = {
+	{ "samsung,pin-pud", PINCFG_TYPE_PUD },
+	{ "samsung,pin-drv", PINCFG_TYPE_DRV },
+	{ "samsung,pin-con-pdn", PINCFG_TYPE_CON_PDN },
+	{ "samsung,pin-pud-pdn", PINCFG_TYPE_PUD_PDN },
+};
+
+/* check if the selector is a valid pin group selector */
+static int samsung_get_group_count(struct pinctrl_dev *pctldev)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	return drvdata->nr_groups;
+}
+
+/* return the name of the group selected by the group selector */
+static const char *samsung_get_group_name(struct pinctrl_dev *pctldev,
+						unsigned selector)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	return drvdata->pin_groups[selector].name;
+}
+
+/* return the pin numbers associated with the specified group */
+static int samsung_get_group_pins(struct pinctrl_dev *pctldev,
+		unsigned selector, const unsigned **pins, unsigned *num_pins)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	*pins = drvdata->pin_groups[selector].pins;
+	*num_pins = drvdata->pin_groups[selector].num_pins;
+	return 0;
+}
+
+/* create pinctrl_map entries by parsing device tree nodes */
+static int samsung_dt_node_to_map(struct pinctrl_dev *pctldev,
+			struct device_node *np, struct pinctrl_map **maps,
+			unsigned *nmaps)
+{
+	struct device *dev = pctldev->dev;
+	struct pinctrl_map *map;
+	unsigned long *cfg = NULL;
+	char *gname, *fname;
+	int cfg_cnt = 0, map_cnt = 0, idx = 0;
+
+	/* count the number of config options specfied in the node */
+	for (idx = 0; idx < ARRAY_SIZE(pcfgs); idx++) {
+		if (of_find_property(np, pcfgs[idx].prop_cfg, NULL))
+			cfg_cnt++;
+	}
+
+	/*
+	 * Find out the number of map entries to create. All the config options
+	 * can be accomadated into a single config map entry.
+	 */
+	if (cfg_cnt)
+		map_cnt = 1;
+	if (of_find_property(np, "samsung,pin-function", NULL))
+		map_cnt++;
+	if (!map_cnt) {
+		dev_err(dev, "node %s does not have either config or function "
+				"configurations\n", np->name);
+		return -EINVAL;
+	}
+
+	/* Allocate memory for pin-map entries */
+	map = kzalloc(sizeof(*map) * map_cnt, GFP_KERNEL);
+	if (!map) {
+		dev_err(dev, "could not alloc memory for pin-maps\n");
+		return -ENOMEM;
+	}
+	*nmaps = 0;
+
+	/*
+	 * Allocate memory for pin group name. The pin group name is derived
+	 * from the node name from which these map entries are be created.
+	 */
+	gname = kzalloc(strlen(np->name) + GSUFFIX_LEN, GFP_KERNEL);
+	if (!gname) {
+		dev_err(dev, "failed to alloc memory for group name\n");
+		goto free_map;
+	}
+	sprintf(gname, "%s%s", np->name, GROUP_SUFFIX);
+
+	/*
+	 * don't have config options? then skip over to creating function
+	 * map entries.
+	 */
+	if (!cfg_cnt)
+		goto skip_cfgs;
+
+	/* Allocate memory for config entries */
+	cfg = kzalloc(sizeof(*cfg) * cfg_cnt, GFP_KERNEL);
+	if (!cfg) {
+		dev_err(dev, "failed to alloc memory for configs\n");
+		goto free_gname;
+	}
+
+	/* Prepare a list of config settings */
+	for (idx = 0, cfg_cnt = 0; idx < ARRAY_SIZE(pcfgs); idx++) {
+		u32 value;
+		if (!of_property_read_u32(np, pcfgs[idx].prop_cfg, &value))
+			cfg[cfg_cnt++] =
+				PINCFG_PACK(pcfgs[idx].cfg_type, value);
+	}
+
+	/* create the config map entry */
+	map[*nmaps].data.configs.group_or_pin = gname;
+	map[*nmaps].data.configs.configs = cfg;
+	map[*nmaps].data.configs.num_configs = cfg_cnt;
+	map[*nmaps].type = PIN_MAP_TYPE_CONFIGS_GROUP;
+	*nmaps += 1;
+
+skip_cfgs:
+	/* create the function map entry */
+	if (of_find_property(np, "samsung,pin-function", NULL)) {
+		fname = kzalloc(strlen(np->name) + FSUFFIX_LEN,	GFP_KERNEL);
+		if (!fname) {
+			dev_err(dev, "failed to alloc memory for func name\n");
+			goto free_cfg;
+		}
+		sprintf(fname, "%s%s", np->name, FUNCTION_SUFFIX);
+
+		map[*nmaps].data.mux.group = gname;
+		map[*nmaps].data.mux.function = fname;
+		map[*nmaps].type = PIN_MAP_TYPE_MUX_GROUP;
+		*nmaps += 1;
+	}
+
+	*maps = map;
+	return 0;
+
+free_cfg:
+	kfree(cfg);
+free_gname:
+	kfree(gname);
+free_map:
+	kfree(map);
+	return -ENOMEM;
+}
+
+/* free the memory allocated to hold the pin-map table */
+static void samsung_dt_free_map(struct pinctrl_dev *pctldev,
+			     struct pinctrl_map *map, unsigned num_maps)
+{
+	int idx;
+
+	for (idx = 0; idx < num_maps; idx++) {
+		if (map[idx].type == PIN_MAP_TYPE_MUX_GROUP) {
+			kfree(map[idx].data.mux.function);
+			if (!idx)
+				kfree(map[idx].data.mux.group);
+		} else if (map->type == PIN_MAP_TYPE_CONFIGS_GROUP) {
+			kfree(map[idx].data.configs.configs);
+			if (!idx)
+				kfree(map[idx].data.configs.group_or_pin);
+		}
+	};
+
+	kfree(map);
+}
+
+/* list of pinctrl callbacks for the pinctrl core */
+static struct pinctrl_ops samsung_pctrl_ops = {
+	.get_groups_count	= samsung_get_group_count,
+	.get_group_name		= samsung_get_group_name,
+	.get_group_pins		= samsung_get_group_pins,
+	.dt_node_to_map		= samsung_dt_node_to_map,
+	.dt_free_map		= samsung_dt_free_map,
+};
+
+/* check if the selector is a valid pin function selector */
+static int samsung_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	return drvdata->nr_functions;
+}
+
+/* return the name of the pin function specified */
+static const char *samsung_pinmux_get_fname(struct pinctrl_dev *pctldev,
+						unsigned selector)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	return drvdata->pmx_functions[selector].name;
+}
+
+/* return the groups associated for the specified function selector */
+static int samsung_pinmux_get_groups(struct pinctrl_dev *pctldev,
+		unsigned selector, const char * const **groups,
+		unsigned * const num_groups)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	*groups = drvdata->pmx_functions[selector].groups;
+	*num_groups = drvdata->pmx_functions[selector].num_groups;
+	return 0;
+}
+
+/*
+ * given a pin number that is local to a pin controller, find out the pin bank
+ * and the register base of the pin bank.
+ */
+static void pin_to_reg_bank(struct gpio_chip *gc, unsigned pin,
+			void __iomem **reg, u32 *offset,
+			struct samsung_pin_bank **bank)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+	struct samsung_pin_bank *b;
+
+	drvdata = dev_get_drvdata(gc->dev);
+	b = drvdata->ctrl->pin_banks;
+
+	while ((pin >= b->pin_base) &&
+			((b->pin_base + b->nr_pins - 1) < pin))
+		b++;
+
+	*reg = drvdata->virt_base + b->pctl_offset;
+	*offset = pin - b->pin_base;
+	if (bank)
+		*bank = b;
+
+	/* some banks have two config registers in a single bank */
+	if (*offset * b->func_width > BITS_PER_LONG)
+		*reg += 4;
+}
+
+/* enable or disable a pinmux function */
+static void samsung_pinmux_setup(struct pinctrl_dev *pctldev, unsigned selector,
+					unsigned group, bool enable)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+	const unsigned int *pins;
+	struct samsung_pin_bank *bank;
+	void __iomem *reg;
+	u32 mask, shift, data, pin_offset, cnt;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	pins = drvdata->pin_groups[group].pins;
+
+	/*
+	 * for each pin in the pin group selected, program the correspoding pin
+	 * pin function number in the config register.
+	 */
+	for (cnt = 0; cnt < drvdata->pin_groups[group].num_pins; cnt++) {
+		pin_to_reg_bank(drvdata->gc, pins[cnt] - drvdata->ctrl->base,
+				&reg, &pin_offset, &bank);
+		mask = (1 << bank->func_width) - 1;
+		shift = pin_offset * bank->func_width;
+
+		data = readl(reg);
+		data &= ~(mask << shift);
+		if (enable)
+			data |= drvdata->pin_groups[group].func << shift;
+		writel(data, reg);
+	}
+}
+
+/* enable a specified pinmux by writing to registers */
+static int samsung_pinmux_enable(struct pinctrl_dev *pctldev, unsigned selector,
+					unsigned group)
+{
+	samsung_pinmux_setup(pctldev, selector, group, true);
+	return 0;
+}
+
+/* disable a specified pinmux by writing to registers */
+static void samsung_pinmux_disable(struct pinctrl_dev *pctldev,
+					unsigned selector, unsigned group)
+{
+	samsung_pinmux_setup(pctldev, selector, group, false);
+}
+
+/*
+ * The calls to gpio_direction_output() and gpio_direction_input()
+ * leads to this function call (via the pinctrl_gpio_direction_{input|output}()
+ * function called from the gpiolib interface).
+ */
+static int samsung_pinmux_gpio_set_direction(struct pinctrl_dev *pctldev,
+		struct pinctrl_gpio_range *range, unsigned offset, bool input)
+{
+	struct samsung_pin_bank *bank;
+	void __iomem *reg;
+	u32 data, pin_offset, mask, shift;
+
+	pin_to_reg_bank(range->gc, offset, &reg, &pin_offset, &bank);
+	mask = (1 << bank->func_width) - 1;
+	shift = pin_offset * bank->func_width;
+
+	data = readl(reg);
+	data &= ~(mask << shift);
+	if (!input)
+		data |= FUNC_OUTPUT << shift;
+	writel(data, reg);
+	return 0;
+}
+
+/* list of pinmux callbacks for the pinmux vertical in pinctrl core */
+static struct pinmux_ops samsung_pinmux_ops = {
+	.get_functions_count	= samsung_get_functions_count,
+	.get_function_name	= samsung_pinmux_get_fname,
+	.get_function_groups	= samsung_pinmux_get_groups,
+	.enable			= samsung_pinmux_enable,
+	.disable		= samsung_pinmux_disable,
+	.gpio_set_direction	= samsung_pinmux_gpio_set_direction,
+};
+
+/* set or get the pin config settings for a specified pin */
+static int samsung_pinconf_rw(struct pinctrl_dev *pctldev, unsigned int pin,
+				unsigned long *config, bool set)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+	struct samsung_pin_bank *bank;
+	void __iomem *reg_base;
+	enum pincfg_type cfg_type = PINCFG_UNPACK_TYPE(*config);
+	u32 data, width, pin_offset, mask, shift;
+	u32 cfg_value, cfg_reg;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	pin_to_reg_bank(drvdata->gc, pin - drvdata->ctrl->base, &reg_base,
+					&pin_offset, &bank);
+
+	switch (cfg_type) {
+	case PINCFG_TYPE_PUD:
+		width = bank->pud_width;
+		cfg_reg = PUD_REG;
+		break;
+	case PINCFG_TYPE_DRV:
+		width = bank->drv_width;
+		cfg_reg = DRV_REG;
+		break;
+	case PINCFG_TYPE_CON_PDN:
+		width = bank->conpdn_width;
+		cfg_reg = CONPDN_REG;
+		break;
+	case PINCFG_TYPE_PUD_PDN:
+		width = bank->pudpdn_width;
+		cfg_reg = PUDPDN_REG;
+		break;
+	default:
+		WARN_ON(1);
+		return -EINVAL;
+	}
+
+	mask = (1 << width) - 1;
+	shift = pin_offset * width;
+	data = readl(reg_base + cfg_reg);
+
+	if (set) {
+		cfg_value = PINCFG_UNPACK_VALUE(*config);
+		data &= ~(mask << shift);
+		data |= (cfg_value << shift);
+		writel(data, reg_base + cfg_reg);
+	} else {
+		data >>= shift;
+		data &= mask;
+		*config = PINCFG_PACK(cfg_type, data);
+	}
+	return 0;
+}
+
+/* set the pin config settings for a specified pin */
+static int samsung_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+				unsigned long config)
+{
+	return samsung_pinconf_rw(pctldev, pin, &config, true);
+}
+
+/* get the pin config settings for a specified pin */
+static int samsung_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
+					unsigned long *config)
+{
+	return samsung_pinconf_rw(pctldev, pin, config, false);
+}
+
+/* set the pin config settings for a specified pin group */
+static int samsung_pinconf_group_set(struct pinctrl_dev *pctldev,
+			unsigned group, unsigned long config)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+	const unsigned int *pins;
+	unsigned int cnt;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	pins = drvdata->pin_groups[group].pins;
+
+	for (cnt = 0; cnt < drvdata->pin_groups[group].num_pins; cnt++)
+		samsung_pinconf_set(pctldev, pins[cnt], config);
+
+	return 0;
+}
+
+/* get the pin config settings for a specified pin group */
+static int samsung_pinconf_group_get(struct pinctrl_dev *pctldev,
+				unsigned int group, unsigned long *config)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+	const unsigned int *pins;
+
+	drvdata = pinctrl_dev_get_drvdata(pctldev);
+	pins = drvdata->pin_groups[group].pins;
+	samsung_pinconf_get(pctldev, pins[0], config);
+	return 0;
+}
+
+/* list of pinconfig callbacks for pinconfig vertical in the pinctrl code */
+static struct pinconf_ops samsung_pinconf_ops = {
+	.pin_config_get		= samsung_pinconf_get,
+	.pin_config_set		= samsung_pinconf_set,
+	.pin_config_group_get	= samsung_pinconf_group_get,
+	.pin_config_group_set	= samsung_pinconf_group_set,
+};
+
+/* gpiolib gpio_set callback function */
+static void samsung_gpio_set(struct gpio_chip *gc, unsigned offset, int value)
+{
+	void __iomem *reg;
+	u32 pin_offset, data;
+
+	pin_to_reg_bank(gc, offset, &reg, &pin_offset, NULL);
+	data = readl(reg + DAT_REG);
+	data &= ~(1 << pin_offset);
+	if (value)
+		data |= 1 << pin_offset;
+	writel(data, reg + DAT_REG);
+}
+
+/* gpiolib gpio_get callback function */
+static int samsung_gpio_get(struct gpio_chip *gc, unsigned offset)
+{
+	void __iomem *reg;
+	u32 pin_offset, data;
+
+	pin_to_reg_bank(gc, offset, &reg, &pin_offset, NULL);
+	data = readl(reg + DAT_REG);
+	data >>= pin_offset;
+	data &= 1;
+	return data;
+}
+
+/*
+ * gpiolib gpio_direction_input callback function. The setting of the pin
+ * mux function as 'gpio input' will be handled by the pinctrl susbsystem
+ * interface.
+ */
+static int samsung_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
+{
+	return pinctrl_gpio_direction_input(gc->base + offset);
+}
+
+/*
+ * gpiolib gpio_direction_output callback function. The setting of the pin
+ * mux function as 'gpio output' will be handled by the pinctrl susbsystem
+ * interface.
+ */
+static int samsung_gpio_direction_output(struct gpio_chip *gc, unsigned offset,
+							int value)
+{
+	samsung_gpio_set(gc, offset, value);
+	return pinctrl_gpio_direction_output(gc->base + offset);
+}
+
+/*
+ * Parse the pin names listed in the 'samsung,pins' property and convert it
+ * into a list of gpio numbers are create a pin group from it.
+ */
+static int __init samsung_pinctrl_parse_dt_pins(struct platform_device *pdev,
+			struct device_node *cfg_np, struct pinctrl_desc *pctl,
+			unsigned int **pin_list, unsigned int *npins)
+{
+	struct device *dev = &pdev->dev;
+	struct property *prop;
+	struct pinctrl_pin_desc const *pdesc = pctl->pins;
+	unsigned int idx = 0, cnt;
+	const char *pin_name;
+
+	*npins = of_property_count_strings(cfg_np, "samsung,pins");
+	if (*npins < 0) {
+		dev_err(dev, "invalid pin list in %s node", cfg_np->name);
+		return -EINVAL;
+	}
+
+	*pin_list = devm_kzalloc(dev, *npins * sizeof(**pin_list), GFP_KERNEL);
+	if (!*pin_list) {
+		dev_err(dev, "failed to allocate memory for pin list\n");
+		return -ENOMEM;
+	}
+
+	of_property_for_each_string(cfg_np, "samsung,pins", prop, pin_name) {
+		for (cnt = 0; cnt < pctl->npins; cnt++) {
+			if (pdesc[cnt].name) {
+				if (!strcmp(pin_name, pdesc[cnt].name)) {
+					(*pin_list)[idx++] = pdesc[cnt].number;
+					break;
+				}
+			}
+		}
+		if (cnt == pctl->npins) {
+			dev_err(dev, "pin %s not valid in %s node\n",
+					pin_name, cfg_np->name);
+			devm_kfree(dev, *pin_list);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * Parse the information about all the available pin groups and pin functions
+ * from device node of the pin-controller. A pin group is formed with all
+ * the pins listed in the "samsung,pins" property.
+ */
+static int __init samsung_pinctrl_parse_dt(struct platform_device *pdev,
+				struct samsung_pinctrl_drv_data *drvdata)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *dev_np = dev->of_node;
+	struct device_node *cfg_np;
+	struct samsung_pin_group *groups, *grp;
+	struct samsung_pmx_func *functions, *func;
+	unsigned *pin_list;
+	unsigned int npins, grp_cnt, func_idx = 0;
+	char *gname, *fname;
+	int ret;
+
+	grp_cnt = of_get_child_count(dev_np);
+	if (!grp_cnt)
+		return -EINVAL;
+
+	groups = devm_kzalloc(dev, grp_cnt * sizeof(*groups), GFP_KERNEL);
+	if (!groups) {
+		dev_err(dev, "failed allocate memory for ping group list\n");
+		return -EINVAL;
+	}
+	grp = groups;
+
+	functions = devm_kzalloc(dev, grp_cnt * sizeof(*functions), GFP_KERNEL);
+	if (!functions) {
+		dev_err(dev, "failed to allocate memory for function list\n");
+		return -EINVAL;
+	}
+	func = functions;
+
+	/*
+	 * Iterate over all the child nodes of the pin controller node
+	 * and create pin groups and pin function lists.
+	 */
+	for_each_child_of_node(dev_np, cfg_np) {
+		u32 function;
+		if (of_find_property(cfg_np, "interrupt-controller", NULL))
+			continue;
+
+		ret = samsung_pinctrl_parse_dt_pins(pdev, cfg_np,
+					&drvdata->pctl,	&pin_list, &npins);
+		if (ret)
+			return ret;
+
+		/* derive pin group name from the node name */
+		gname = devm_kzalloc(dev, strlen(cfg_np->name) + GSUFFIX_LEN,
+					GFP_KERNEL);
+		if (!gname) {
+			dev_err(dev, "failed to alloc memory for group name\n");
+			return -ENOMEM;
+		}
+		sprintf(gname, "%s%s", cfg_np->name, GROUP_SUFFIX);
+
+		grp->name = gname;
+		grp->pins = pin_list;
+		grp->num_pins = npins;
+		of_property_read_u32(cfg_np, "samsung,pin-function", &function);
+		grp->func = function;
+		grp++;
+
+		if (!of_find_property(cfg_np, "samsung,pin-function", NULL))
+			continue;
+
+		/* derive function name from the node name */
+		fname = devm_kzalloc(dev, strlen(cfg_np->name) + FSUFFIX_LEN,
+					GFP_KERNEL);
+		if (!fname) {
+			dev_err(dev, "failed to alloc memory for func name\n");
+			return -ENOMEM;
+		}
+		sprintf(fname, "%s%s", cfg_np->name, FUNCTION_SUFFIX);
+
+		func->name = fname;
+		func->groups = devm_kzalloc(dev, sizeof(char *), GFP_KERNEL);
+		if (!func->groups) {
+			dev_err(dev, "failed to alloc memory for group list "
+					"in pin function");
+			return -ENOMEM;
+		}
+		func->groups[0] = gname;
+		func->num_groups = 1;
+		func++;
+		func_idx++;
+	}
+
+	drvdata->pin_groups = groups;
+	drvdata->nr_groups = grp_cnt;
+	drvdata->pmx_functions = functions;
+	drvdata->nr_functions = func_idx;
+
+	return 0;
+}
+
+/* register the pinctrl interface with the pinctrl subsystem */
+static int __init samsung_pinctrl_register(struct platform_device *pdev,
+				struct samsung_pinctrl_drv_data *drvdata)
+{
+	struct pinctrl_desc *ctrldesc = &drvdata->pctl;
+	struct pinctrl_pin_desc *pindesc, *pdesc;
+	struct samsung_pin_bank *pin_bank;
+	char *pin_names;
+	int pin, bank, ret;
+
+	ctrldesc->name = "samsung-pinctrl";
+	ctrldesc->owner = THIS_MODULE;
+	ctrldesc->pctlops = &samsung_pctrl_ops;
+	ctrldesc->pmxops = &samsung_pinmux_ops;
+	ctrldesc->confops = &samsung_pinconf_ops;
+
+	pindesc = devm_kzalloc(&pdev->dev, sizeof(*pindesc) *
+			drvdata->ctrl->nr_pins, GFP_KERNEL);
+	if (!pindesc) {
+		dev_err(&pdev->dev, "mem alloc for pin descriptors failed\n");
+		return -ENOMEM;
+	}
+	ctrldesc->pins = pindesc;
+	ctrldesc->npins = drvdata->ctrl->nr_pins;
+	ctrldesc->npins = drvdata->ctrl->nr_pins;
+
+	/* dynamically populate the pin number and pin name for pindesc */
+	for (pin = 0, pdesc = pindesc; pin < ctrldesc->npins; pin++, pdesc++)
+		pdesc->number = pin + drvdata->ctrl->base;
+
+	/*
+	 * allocate space for storing the dynamically generated names for all
+	 * the pins which belong to this pin-controller.
+	 */
+	pin_names = devm_kzalloc(&pdev->dev, sizeof(char) * PIN_NAME_LENGTH *
+					drvdata->ctrl->nr_pins, GFP_KERNEL);
+	if (!pin_names) {
+		dev_err(&pdev->dev, "mem alloc for pin names failed\n");
+		return -ENOMEM;
+	}
+
+	/* for each pin, the name of the pin is pin-bank name + pin number */
+	for (bank = 0; bank < drvdata->ctrl->nr_banks; bank++) {
+		pin_bank = &drvdata->ctrl->pin_banks[bank];
+		for (pin = 0; pin < pin_bank->nr_pins; pin++) {
+			sprintf(pin_names, "%s-%d", pin_bank->name, pin);
+			pdesc = pindesc + pin_bank->pin_base + pin;
+			pdesc->name = pin_names;
+			pin_names += PIN_NAME_LENGTH;
+		}
+	}
+
+	drvdata->pctl_dev = pinctrl_register(ctrldesc, &pdev->dev, drvdata);
+	if (!drvdata->pctl_dev) {
+		dev_err(&pdev->dev, "could not register pinctrl driver\n");
+		return -EINVAL;
+	}
+
+	drvdata->grange.name = "samsung-pctrl-gpio-range";
+	drvdata->grange.id = 0;
+	drvdata->grange.base = drvdata->ctrl->base;
+	drvdata->grange.npins = drvdata->ctrl->nr_pins;
+	drvdata->grange.gc = drvdata->gc;
+	pinctrl_add_gpio_range(drvdata->pctl_dev, &drvdata->grange);
+
+	ret = samsung_pinctrl_parse_dt(pdev, drvdata);
+	if (ret) {
+		pinctrl_unregister(drvdata->pctl_dev);
+		return ret;
+	}
+
+	return 0;
+}
+
+/* register the gpiolib interface with the gpiolib subsystem */
+static int __init samsung_gpiolib_register(struct platform_device *pdev,
+				struct samsung_pinctrl_drv_data *drvdata)
+{
+	struct gpio_chip *gc;
+	int ret;
+
+	gc = devm_kzalloc(&pdev->dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc) {
+		dev_err(&pdev->dev, "mem alloc for gpio_chip failed\n");
+		return -ENOMEM;
+	}
+
+	drvdata->gc = gc;
+	gc->base = drvdata->ctrl->base;
+	gc->ngpio = drvdata->ctrl->nr_pins;
+	gc->dev = &pdev->dev;
+	gc->set = samsung_gpio_set;
+	gc->get = samsung_gpio_get;
+	gc->direction_input = samsung_gpio_direction_input;
+	gc->direction_output = samsung_gpio_direction_output;
+	gc->label = drvdata->ctrl->label;
+	gc->owner = THIS_MODULE;
+	ret = gpiochip_add(gc);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register gpio_chip %s, error "
+					"code: %d\n", gc->label, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+/* unregister the gpiolib interface with the gpiolib subsystem */
+static int __init samsung_gpiolib_unregister(struct platform_device *pdev,
+				struct samsung_pinctrl_drv_data *drvdata)
+{
+	int ret = gpiochip_remove(drvdata->gc);
+	if (ret) {
+		dev_err(&pdev->dev, "gpio chip remove failed\n");
+		return ret;
+	}
+	return 0;
+}
+
+static const struct of_device_id samsung_pinctrl_dt_match[];
+
+/* retrieve the soc specific data */
+static inline struct samsung_pin_ctrl *samsung_pinctrl_get_soc_data(
+				struct platform_device *pdev)
+{
+	int id;
+	const struct of_device_id *match;
+	const struct device_node *node = pdev->dev.of_node;
+
+	id = of_alias_get_id(pdev->dev.of_node, "pinctrl");
+	if (id < 0) {
+		dev_err(&pdev->dev, "failed to get alias id\n");
+		return NULL;
+	}
+	match = of_match_node(samsung_pinctrl_dt_match, node);
+	return (struct samsung_pin_ctrl *)match->data + id;
+}
+
+static int __devinit samsung_pinctrl_probe(struct platform_device *pdev)
+{
+	struct samsung_pinctrl_drv_data *drvdata;
+	struct device *dev = &pdev->dev;
+	struct samsung_pin_ctrl *ctrl;
+	struct resource *res;
+	int ret;
+
+	if (!dev->of_node) {
+		dev_err(dev, "device tree node not found\n");
+		return -ENODEV;
+	}
+
+	ctrl = samsung_pinctrl_get_soc_data(pdev);
+	if (!ctrl) {
+		dev_err(&pdev->dev, "driver data not available\n");
+		return -EINVAL;
+	}
+
+	drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL);
+	if (!drvdata) {
+		dev_err(dev, "failed to allocate memory for driver's "
+				"private data\n");
+		return -ENOMEM;
+	}
+	drvdata->ctrl = ctrl;
+	drvdata->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "cannot find IO resource\n");
+		return -ENOENT;
+	}
+
+	drvdata->virt_base = devm_request_and_ioremap(&pdev->dev, res);
+	if (!drvdata->virt_base) {
+		dev_err(dev, "ioremap failed\n");
+		return -ENODEV;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (res)
+		drvdata->irq = res->start;
+
+	ret = samsung_gpiolib_register(pdev, drvdata);
+	if (ret)
+		return ret;
+
+	ret = samsung_pinctrl_register(pdev, drvdata);
+	if (ret) {
+		samsung_gpiolib_unregister(pdev, drvdata);
+		return ret;
+	}
+
+	if (ctrl->eint_gpio_init)
+		ctrl->eint_gpio_init(drvdata);
+	if (ctrl->eint_wkup_init)
+		ctrl->eint_wkup_init(drvdata);
+
+	platform_set_drvdata(pdev, drvdata);
+	return 0;
+}
+
+static const struct of_device_id samsung_pinctrl_dt_match[] = {
+	{ .compatible = "samsung,pinctrl-exynos4210",
+		.data = (void *)exynos4210_pin_ctrl },
+	{},
+};
+MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match);
+
+static struct platform_driver samsung_pinctrl_driver = {
+	.probe		= samsung_pinctrl_probe,
+	.driver = {
+		.name	= "samsung-pinctrl",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(samsung_pinctrl_dt_match),
+	},
+};
+
+static int __init samsung_pinctrl_drv_register(void)
+{
+	return platform_driver_register(&samsung_pinctrl_driver);
+}
+postcore_initcall(samsung_pinctrl_drv_register);
+
+static void __exit samsung_pinctrl_drv_unregister(void)
+{
+	platform_driver_unregister(&samsung_pinctrl_driver);
+}
+module_exit(samsung_pinctrl_drv_unregister);
+
+MODULE_AUTHOR("Thomas Abraham <thomas.ab@samsung.com>");
+MODULE_DESCRIPTION("Samsung pinctrl driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pinctrl/pinctrl-samsung.h b/drivers/pinctrl/pinctrl-samsung.h
new file mode 100644
index 0000000..b895693
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-samsung.h
@@ -0,0 +1,239 @@
+/*
+ * pin-controller/pin-mux/pin-config/gpio-driver for Samsung's SoC's.
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2012 Linaro Ltd
+ *		http://www.linaro.org
+ *
+ * Author: Thomas Abraham <thomas.ab@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __PINCTRL_SAMSUNG_H
+#define __PINCTRL_SAMSUNG_H
+
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/machine.h>
+
+/* register offsets within a pin bank */
+#define DAT_REG		0x4
+#define PUD_REG		0x8
+#define DRV_REG		0xC
+#define CONPDN_REG	0x10
+#define PUDPDN_REG	0x14
+
+/* pinmux function number for pin as gpio output line */
+#define FUNC_OUTPUT	0x1
+
+/**
+ * enum pincfg_type - possible pin configuration types supported.
+ * @PINCFG_TYPE_PUD: Pull up/down configuration.
+ * @PINCFG_TYPE_DRV: Drive strength configuration.
+ * @PINCFG_TYPE_CON_PDN: Pin function in power down mode.
+ * @PINCFG_TYPE_PUD_PDN: Pull up/down configuration in power down mode.
+ */
+enum pincfg_type {
+	PINCFG_TYPE_PUD,
+	PINCFG_TYPE_DRV,
+	PINCFG_TYPE_CON_PDN,
+	PINCFG_TYPE_PUD_PDN,
+};
+
+/*
+ * pin configuration (pull up/down and drive strength) type and its value are
+ * packed together into a 16-bits. The upper 8-bits represent the configuration
+ * type and the lower 8-bits hold the value of the configuration type.
+ */
+#define PINCFG_TYPE_MASK		0xFF
+#define PINCFG_VALUE_SHIFT		8
+#define PINCFG_VALUE_MASK		(0xFF << PINCFG_VALUE_SHIFT)
+#define PINCFG_PACK(type, value)	(((value) << PINCFG_VALUE_SHIFT) | type)
+#define PINCFG_UNPACK_TYPE(cfg)		((cfg) & PINCFG_TYPE_MASK)
+#define PINCFG_UNPACK_VALUE(cfg)	(((cfg) & PINCFG_VALUE_MASK) >> \
+						PINCFG_VALUE_SHIFT)
+/**
+ * enum eint_type - possible external interrupt types.
+ * @EINT_TYPE_NONE: bank does not support external interrupts
+ * @EINT_TYPE_GPIO: bank supportes external gpio interrupts
+ * @EINT_TYPE_WKUP: bank supportes external wakeup interrupts
+ *
+ * Samsung GPIO controller groups all the available pins into banks. The pins
+ * in a pin bank can support external gpio interrupts or external wakeup
+ * interrupts or no interrupts at all. From a software perspective, the only
+ * difference between external gpio and external wakeup interrupts is that
+ * the wakeup interrupts can additionally wakeup the system if it is in
+ * suspended state.
+ */
+enum eint_type {
+	EINT_TYPE_NONE,
+	EINT_TYPE_GPIO,
+	EINT_TYPE_WKUP,
+};
+
+/* maximum length of a pin in pin descriptor (example: "gpa0-0") */
+#define PIN_NAME_LENGTH	10
+
+#define PIN_GROUP(n, p, f)				\
+	{						\
+		.name		= n,			\
+		.pins		= p,			\
+		.num_pins	= ARRAY_SIZE(p),	\
+		.func		= f			\
+	}
+
+#define PMX_FUNC(n, g)					\
+	{						\
+		.name		= n,			\
+		.groups		= g,			\
+		.num_groups	= ARRAY_SIZE(g),	\
+	}
+
+struct samsung_pinctrl_drv_data;
+
+/**
+ * struct samsung_pin_bank: represent a controller pin-bank.
+ * @reg_offset: starting offset of the pin-bank registers.
+ * @pin_base: starting pin number of the bank.
+ * @nr_pins: number of pins included in this bank.
+ * @func_width: width of the function selector bit field.
+ * @pud_width: width of the pin pull up/down selector bit field.
+ * @drv_width: width of the pin driver strength selector bit field.
+ * @conpdn_width: width of the sleep mode function selector bin field.
+ * @pudpdn_width: width of the sleep mode pull up/down selector bit field.
+ * @eint_type: type of the external interrupt supported by the bank.
+ * @irq_base: starting controller local irq number of the bank.
+ * @name: name to be prefixed for each pin in this pin bank.
+ */
+struct samsung_pin_bank {
+	u32		pctl_offset;
+	u32		pin_base;
+	u8		nr_pins;
+	u8		func_width;
+	u8		pud_width;
+	u8		drv_width;
+	u8		conpdn_width;
+	u8		pudpdn_width;
+	enum eint_type	eint_type;
+	u32		irq_base;
+	char		*name;
+};
+
+/**
+ * struct samsung_pin_ctrl: represent a pin controller.
+ * @pin_banks: list of pin banks included in this controller.
+ * @nr_banks: number of pin banks.
+ * @base: starting system wide pin number.
+ * @nr_pins: number of pins supported by the controller.
+ * @nr_gint: number of external gpio interrupts supported.
+ * @nr_wint: number of external wakeup interrupts supported.
+ * @geint_con: offset of the ext-gpio controller registers.
+ * @geint_mask: offset of the ext-gpio interrupt mask registers.
+ * @geint_pend: offset of the ext-gpio interrupt pending registers.
+ * @weint_con: offset of the ext-wakeup controller registers.
+ * @weint_mask: offset of the ext-wakeup interrupt mask registers.
+ * @weint_pend: offset of the ext-wakeup interrupt pending registers.
+ * @svc: offset of the interrupt service register.
+ * @eint_gpio_init: platform specific callback to setup the external gpio
+ *	interrupts for the controller.
+ * @eint_wkup_init: platform specific callback to setup the external wakeup
+ *	interrupts for the controller.
+ * @label: for debug information.
+ */
+struct samsung_pin_ctrl {
+	struct samsung_pin_bank	*pin_banks;
+	u32		nr_banks;
+
+	u32		base;
+	u32		nr_pins;
+	u32		nr_gint;
+	u32		nr_wint;
+
+	u32		geint_con;
+	u32		geint_mask;
+	u32		geint_pend;
+
+	u32		weint_con;
+	u32		weint_mask;
+	u32		weint_pend;
+
+	u32		svc;
+
+	int		(*eint_gpio_init)(struct samsung_pinctrl_drv_data *);
+	int		(*eint_wkup_init)(struct samsung_pinctrl_drv_data *);
+	char		*label;
+};
+
+/**
+ * struct samsung_pinctrl_drv_data: wrapper for holding driver data together.
+ * @virt_base: register base address of the controller.
+ * @dev: device instance representing the controller.
+ * @irq: interrpt number used by the controller to notify gpio interrupts.
+ * @ctrl: pin controller instance managed by the driver.
+ * @pctl: pin controller descriptor registered with the pinctrl subsystem.
+ * @pctl_dev: cookie representing pinctrl device instance.
+ * @pin_groups: list of pin groups available to the driver.
+ * @nr_groups: number of such pin groups.
+ * @pmx_functions: list of pin functions available to the driver.
+ * @nr_function: number of such pin functions.
+ * @gc: gpio_chip instance registered with gpiolib.
+ * @grange: linux gpio pin range supported by this controller.
+ */
+struct samsung_pinctrl_drv_data {
+	void __iomem			*virt_base;
+	struct device			*dev;
+	int				irq;
+
+	struct samsung_pin_ctrl		*ctrl;
+	struct pinctrl_desc		pctl;
+	struct pinctrl_dev		*pctl_dev;
+
+	const struct samsung_pin_group	*pin_groups;
+	unsigned int			nr_groups;
+	const struct samsung_pmx_func	*pmx_functions;
+	unsigned int			nr_functions;
+
+	struct irq_domain		*gpio_irqd;
+	struct irq_domain		*wkup_irqd;
+
+	struct gpio_chip		*gc;
+	struct pinctrl_gpio_range	grange;
+};
+
+/**
+ * struct samsung_pin_group: represent group of pins of a pinmux function.
+ * @name: name of the pin group, used to lookup the group.
+ * @pins: the pins included in this group.
+ * @num_pins: number of pins included in this group.
+ * @func: the function number to be programmed when selected.
+ */
+struct samsung_pin_group {
+	const char		*name;
+	const unsigned int	*pins;
+	u8			num_pins;
+	u8			func;
+};
+
+/**
+ * struct samsung_pmx_func: represent a pin function.
+ * @name: name of the pin function, used to lookup the function.
+ * @groups: one or more names of pin groups that provide this function.
+ * @num_groups: number of groups included in @groups.
+ */
+struct samsung_pmx_func {
+	const char		*name;
+	const char		**groups;
+	u8			num_groups;
+};
+
+/* list of all exported SoC specific data */
+extern struct samsung_pin_ctrl exynos4210_pin_ctrl[];
+
+#endif /* __PINCTRL_SAMSUNG_H */
