diff mbox series

[v11,3/5] dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver

Message ID 20190319172651.10012-3-dmurphy@ti.com
State Superseded
Headers show
Series [v11,1/5] can: m_can: Create a m_can platform framework | expand

Commit Message

Dan Murphy March 19, 2019, 5:26 p.m. UTC 
DT binding documentation for TI TCAN4x5x driver.

Signed-off-by: Dan Murphy <dmurphy@ti.com>

---

v11 - No changes - https://lore.kernel.org/patchwork/patch/1051178/

v10 - No changes - https://lore.kernel.org/patchwork/patch/1050488/
v9 - No Changes - https://lore.kernel.org/patchwork/patch/1050118/
v8 - No Changes - https://lore.kernel.org/patchwork/patch/1047981/
v7 - Made device state optional - https://lore.kernel.org/patchwork/patch/1047218/
v6 - No changes - https://lore.kernel.org/patchwork/patch/1042445/

 .../devicetree/bindings/net/can/tcan4x5x.txt  | 37 +++++++++++++++++++
 1 file changed, 37 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/can/tcan4x5x.txt

-- 
2.20.1.390.gb5101f9297
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
new file mode 100644
index 000000000000..c388f7d9feb1
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
@@ -0,0 +1,37 @@ 
+Texas Instruments TCAN4x5x CAN Controller
+================================================
+
+This file provides device node information for the TCAN4x5x interface contains.
+
+Required properties:
+	- compatible: "ti,tcan4x5x"
+	- reg: 0
+	- #address-cells: 1
+	- #size-cells: 0
+	- spi-max-frequency: Maximum frequency of the SPI bus the chip can
+			     operate at should be less than or equal to 18 MHz.
+	- data-ready-gpios: Interrupt GPIO for data and error reporting.
+	- device-wake-gpios: Wake up GPIO to wake up the TCAN device.
+
+See Documentation/devicetree/bindings/net/can/m_can.txt for additional
+required property details.
+
+Optional properties:
+	- reset-gpios: Hardwired output GPIO. If not defined then software
+		       reset.
+	- device-state-gpios: Input GPIO that indicates if the device is in
+			      a sleep state or if the device is active.
+
+Example:
+tcan4x5x: tcan4x5x@0 {
+		compatible = "ti,tcan4x5x";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <10000000>;
+		bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>;
+		data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+		device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+};