diff --git a/drivers/net/ethernet/mellanox/Kconfig b/drivers/net/ethernet/mellanox/Kconfig
index ff6613a5cdd3..b4f66eb9ddb9 100644
--- a/drivers/net/ethernet/mellanox/Kconfig
+++ b/drivers/net/ethernet/mellanox/Kconfig
@@ -22,5 +22,6 @@ source "drivers/net/ethernet/mellanox/mlx4/Kconfig"
 source "drivers/net/ethernet/mellanox/mlx5/core/Kconfig"
 source "drivers/net/ethernet/mellanox/mlxsw/Kconfig"
 source "drivers/net/ethernet/mellanox/mlxfw/Kconfig"
+source "drivers/net/ethernet/mellanox/mlxbf_gige/Kconfig"
 
 endif # NET_VENDOR_MELLANOX
diff --git a/drivers/net/ethernet/mellanox/Makefile b/drivers/net/ethernet/mellanox/Makefile
index 79773ac331ee..d4b5f547a727 100644
--- a/drivers/net/ethernet/mellanox/Makefile
+++ b/drivers/net/ethernet/mellanox/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_MLX4_CORE) += mlx4/
 obj-$(CONFIG_MLX5_CORE) += mlx5/core/
 obj-$(CONFIG_MLXSW_CORE) += mlxsw/
 obj-$(CONFIG_MLXFW) += mlxfw/
+obj-$(CONFIG_MLXBF_GIGE) += mlxbf_gige/
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/Kconfig b/drivers/net/ethernet/mellanox/mlxbf_gige/Kconfig
new file mode 100644
index 000000000000..4cdebafaf222
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/Kconfig
@@ -0,0 +1,13 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+#
+# Mellanox GigE driver configuration
+#
+
+config MLXBF_GIGE
+	tristate "Mellanox Technologies BlueField Gigabit Ethernet support"
+	depends on (ARM64 && ACPI) || COMPILE_TEST
+	select PHYLIB
+	help
+	  The second generation BlueField SoC from Mellanox Technologies
+	  supports an out-of-band Gigabit Ethernet management port to the
+	  Arm subsystem.
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/Makefile b/drivers/net/ethernet/mellanox/mlxbf_gige/Makefile
new file mode 100644
index 000000000000..e57c1375f236
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/Makefile
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+obj-$(CONFIG_MLXBF_GIGE) += mlxbf_gige.o
+
+mlxbf_gige-y := mlxbf_gige_ethtool.o \
+		mlxbf_gige_gpio.o \
+		mlxbf_gige_intr.o \
+		mlxbf_gige_main.o \
+		mlxbf_gige_mdio.o \
+		mlxbf_gige_rx.o   \
+		mlxbf_gige_tx.o
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h
new file mode 100644
index 000000000000..6945abf946d2
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h
@@ -0,0 +1,193 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause */
+
+/* Header file for Gigabit Ethernet driver for Mellanox BlueField SoC
+ * - this file contains software data structures and any chip-specific
+ *   data structures (e.g. TX WQE format) that are memory resident.
+ *
+ * Copyright (C) 2020-2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#ifndef __MLXBF_GIGE_H__
+#define __MLXBF_GIGE_H__
+
+#include <linux/io-64-nonatomic-lo-hi.h>
+#include <linux/irqreturn.h>
+#include <linux/netdevice.h>
+#include <linux/irq.h>
+
+/* The silicon design supports a maximum RX ring size of
+ * 32K entries. Based on current testing this maximum size
+ * is not required to be supported.  Instead the RX ring
+ * will be capped at a realistic value of 1024 entries.
+ */
+#define MLXBF_GIGE_MIN_RXQ_SZ     32
+#define MLXBF_GIGE_MAX_RXQ_SZ     1024
+#define MLXBF_GIGE_DEFAULT_RXQ_SZ 128
+
+#define MLXBF_GIGE_MIN_TXQ_SZ     4
+#define MLXBF_GIGE_MAX_TXQ_SZ     256
+#define MLXBF_GIGE_DEFAULT_TXQ_SZ 128
+
+#define MLXBF_GIGE_DEFAULT_BUF_SZ 2048
+
+#define MLXBF_GIGE_DMA_PAGE_SZ    4096
+#define MLXBF_GIGE_DMA_PAGE_SHIFT 12
+
+/* There are four individual MAC RX filters. Currently
+ * two of them are being used: one for the broadcast MAC
+ * (index 0) and one for local MAC (index 1)
+ */
+#define MLXBF_GIGE_BCAST_MAC_FILTER_IDX 0
+#define MLXBF_GIGE_LOCAL_MAC_FILTER_IDX 1
+
+/* Define for broadcast MAC literal */
+#define BCAST_MAC_ADDR 0xFFFFFFFFFFFF
+
+/* There are three individual interrupts:
+ *   1) Errors, "OOB" interrupt line
+ *   2) Receive Packet, "OOB_LLU" interrupt line
+ *   3) LLU and PLU Events, "OOB_PLU" interrupt line
+ */
+#define MLXBF_GIGE_ERROR_INTR_IDX       0
+#define MLXBF_GIGE_RECEIVE_PKT_INTR_IDX 1
+#define MLXBF_GIGE_LLU_PLU_INTR_IDX     2
+#define MLXBF_GIGE_PHY_INT_N            3
+
+#define MLXBF_GIGE_MDIO_DEFAULT_PHY_ADDR 0x3
+
+#define MLXBF_GIGE_DEFAULT_PHY_INT_GPIO 12
+
+struct mlxbf_gige_stats {
+	u64 hw_access_errors;
+	u64 tx_invalid_checksums;
+	u64 tx_small_frames;
+	u64 tx_index_errors;
+	u64 sw_config_errors;
+	u64 sw_access_errors;
+	u64 rx_truncate_errors;
+	u64 rx_mac_errors;
+	u64 rx_din_dropped_pkts;
+	u64 tx_fifo_full;
+	u64 rx_filter_passed_pkts;
+	u64 rx_filter_discard_pkts;
+};
+
+struct mlxbf_gige {
+	void __iomem *base;
+	void __iomem *llu_base;
+	void __iomem *plu_base;
+	struct device *dev;
+	struct net_device *netdev;
+	struct platform_device *pdev;
+	void __iomem *mdio_io;
+	struct mii_bus *mdiobus;
+	void __iomem *gpio_io;
+	struct irq_domain *irqdomain;
+	u32 phy_int_gpio_mask;
+	spinlock_t lock;
+	spinlock_t gpio_lock;
+	u16 rx_q_entries;
+	u16 tx_q_entries;
+	u64 *tx_wqe_base;
+	dma_addr_t tx_wqe_base_dma;
+	u64 *tx_wqe_next;
+	u64 *tx_cc;
+	dma_addr_t tx_cc_dma;
+	dma_addr_t *rx_wqe_base;
+	dma_addr_t rx_wqe_base_dma;
+	u64 *rx_cqe_base;
+	dma_addr_t rx_cqe_base_dma;
+	u16 tx_pi;
+	u16 prev_tx_ci;
+	u64 error_intr_count;
+	u64 rx_intr_count;
+	u64 llu_plu_intr_count;
+	struct sk_buff *rx_skb[MLXBF_GIGE_MAX_RXQ_SZ];
+	struct sk_buff *tx_skb[MLXBF_GIGE_MAX_TXQ_SZ];
+	int error_irq;
+	int rx_irq;
+	int llu_plu_irq;
+	int phy_irq;
+	int hw_phy_irq;
+	bool promisc_enabled;
+	u8 valid_polarity;
+	struct napi_struct napi;
+	struct mlxbf_gige_stats stats;
+	u32 tx_pause;
+	u32 rx_pause;
+	u32 aneg_pause;
+};
+
+/* Rx Work Queue Element definitions */
+#define MLXBF_GIGE_RX_WQE_SZ                   8
+
+/* Rx Completion Queue Element definitions */
+#define MLXBF_GIGE_RX_CQE_SZ                   8
+#define MLXBF_GIGE_RX_CQE_PKT_LEN_MASK         GENMASK(10, 0)
+#define MLXBF_GIGE_RX_CQE_VALID_MASK           GENMASK(11, 11)
+#define MLXBF_GIGE_RX_CQE_PKT_STATUS_MASK      GENMASK(15, 12)
+#define MLXBF_GIGE_RX_CQE_PKT_STATUS_MAC_ERR   GENMASK(12, 12)
+#define MLXBF_GIGE_RX_CQE_PKT_STATUS_TRUNCATED GENMASK(13, 13)
+#define MLXBF_GIGE_RX_CQE_CHKSUM_MASK          GENMASK(31, 16)
+
+/* Tx Work Queue Element definitions */
+#define MLXBF_GIGE_TX_WQE_SZ_QWORDS            2
+#define MLXBF_GIGE_TX_WQE_SZ                   16
+#define MLXBF_GIGE_TX_WQE_PKT_LEN_MASK         GENMASK(10, 0)
+#define MLXBF_GIGE_TX_WQE_UPDATE_MASK          GENMASK(31, 31)
+#define MLXBF_GIGE_TX_WQE_CHKSUM_LEN_MASK      GENMASK(42, 32)
+#define MLXBF_GIGE_TX_WQE_CHKSUM_START_MASK    GENMASK(55, 48)
+#define MLXBF_GIGE_TX_WQE_CHKSUM_OFFSET_MASK   GENMASK(63, 56)
+
+/* Macro to return packet length of specified TX WQE */
+#define MLXBF_GIGE_TX_WQE_PKT_LEN(tx_wqe_addr) \
+	(*(tx_wqe_addr + 1) & MLXBF_GIGE_TX_WQE_PKT_LEN_MASK)
+
+/* Tx Completion Count */
+#define MLXBF_GIGE_TX_CC_SZ                    8
+
+/* List of resources in ACPI table */
+enum mlxbf_gige_res {
+	MLXBF_GIGE_RES_MAC,
+	MLXBF_GIGE_RES_MDIO9,
+	MLXBF_GIGE_RES_GPIO0,
+	MLXBF_GIGE_RES_LLU,
+	MLXBF_GIGE_RES_PLU
+};
+
+/* Version of register data returned by mlxbf_gige_get_regs() */
+#define MLXBF_GIGE_REGS_VERSION 1
+
+int mlxbf_gige_mdio_probe(struct platform_device *pdev,
+			  struct mlxbf_gige *priv);
+void mlxbf_gige_mdio_remove(struct mlxbf_gige *priv);
+irqreturn_t mlxbf_gige_mdio_handle_phy_interrupt(int irq, void *dev_id);
+void mlxbf_gige_mdio_enable_phy_int(struct mlxbf_gige *priv);
+
+void mlxbf_gige_set_mac_rx_filter(struct mlxbf_gige *priv,
+				  unsigned int index, u64 dmac);
+void mlxbf_gige_get_mac_rx_filter(struct mlxbf_gige *priv,
+				  unsigned int index, u64 *dmac);
+void mlxbf_gige_enable_promisc(struct mlxbf_gige *priv);
+void mlxbf_gige_disable_promisc(struct mlxbf_gige *priv);
+int mlxbf_gige_rx_init(struct mlxbf_gige *priv);
+void mlxbf_gige_rx_deinit(struct mlxbf_gige *priv);
+int mlxbf_gige_tx_init(struct mlxbf_gige *priv);
+void mlxbf_gige_tx_deinit(struct mlxbf_gige *priv);
+bool mlxbf_gige_handle_tx_complete(struct mlxbf_gige *priv);
+netdev_tx_t mlxbf_gige_start_xmit(struct sk_buff *skb,
+				  struct net_device *netdev);
+struct sk_buff *mlxbf_gige_alloc_skb(struct mlxbf_gige *priv,
+				     unsigned int map_len,
+				     dma_addr_t *buf_dma,
+				     enum dma_data_direction dir);
+int mlxbf_gige_request_irqs(struct mlxbf_gige *priv);
+void mlxbf_gige_free_irqs(struct mlxbf_gige *priv);
+int mlxbf_gige_poll(struct napi_struct *napi, int budget);
+extern const struct ethtool_ops mlxbf_gige_ethtool_ops;
+void mlxbf_gige_update_tx_wqe_next(struct mlxbf_gige *priv);
+
+int mlxbf_gige_gpio_init(struct platform_device *pdev, struct mlxbf_gige *priv);
+void mlxbf_gige_gpio_free(struct mlxbf_gige *priv);
+
+#endif /* !defined(__MLXBF_GIGE_H__) */
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_ethtool.c b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_ethtool.c
new file mode 100644
index 000000000000..a1b8c3177c1a
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_ethtool.c
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+/* Ethtool support for Mellanox Gigabit Ethernet driver
+ *
+ * Copyright (C) 2020-2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#include <linux/phy.h>
+
+#include "mlxbf_gige.h"
+#include "mlxbf_gige_regs.h"
+
+/* Start of struct ethtool_ops functions */
+static int mlxbf_gige_get_regs_len(struct net_device *netdev)
+{
+	return MLXBF_GIGE_MMIO_REG_SZ;
+}
+
+static void mlxbf_gige_get_regs(struct net_device *netdev,
+				struct ethtool_regs *regs, void *p)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+
+	regs->version = MLXBF_GIGE_REGS_VERSION;
+
+	/* Read entire MMIO register space and store results
+	 * into the provided buffer. Each 64-bit word is converted
+	 * to big-endian to make the output more readable.
+	 *
+	 * NOTE: by design, a read to an offset without an existing
+	 *       register will be acknowledged and return zero.
+	 */
+	memcpy_fromio(p, priv->base, MLXBF_GIGE_MMIO_REG_SZ);
+}
+
+static void mlxbf_gige_get_ringparam(struct net_device *netdev,
+				     struct ethtool_ringparam *ering)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+
+	ering->rx_max_pending = MLXBF_GIGE_MAX_RXQ_SZ;
+	ering->tx_max_pending = MLXBF_GIGE_MAX_TXQ_SZ;
+	ering->rx_pending = priv->rx_q_entries;
+	ering->tx_pending = priv->tx_q_entries;
+}
+
+static const struct {
+	const char string[ETH_GSTRING_LEN];
+} mlxbf_gige_ethtool_stats_keys[] = {
+	{ "hw_access_errors" },
+	{ "tx_invalid_checksums" },
+	{ "tx_small_frames" },
+	{ "tx_index_errors" },
+	{ "sw_config_errors" },
+	{ "sw_access_errors" },
+	{ "rx_truncate_errors" },
+	{ "rx_mac_errors" },
+	{ "rx_din_dropped_pkts" },
+	{ "tx_fifo_full" },
+	{ "rx_filter_passed_pkts" },
+	{ "rx_filter_discard_pkts" },
+};
+
+static int mlxbf_gige_get_sset_count(struct net_device *netdev, int stringset)
+{
+	if (stringset != ETH_SS_STATS)
+		return -EOPNOTSUPP;
+	return ARRAY_SIZE(mlxbf_gige_ethtool_stats_keys);
+}
+
+static void mlxbf_gige_get_strings(struct net_device *netdev, u32 stringset,
+				   u8 *buf)
+{
+	if (stringset != ETH_SS_STATS)
+		return;
+	memcpy(buf, &mlxbf_gige_ethtool_stats_keys,
+	       sizeof(mlxbf_gige_ethtool_stats_keys));
+}
+
+static void mlxbf_gige_get_ethtool_stats(struct net_device *netdev,
+					 struct ethtool_stats *estats,
+					 u64 *data)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+
+	/* Fill data array with interface statistics
+	 *
+	 * NOTE: the data writes must be in
+	 *       sync with the strings shown in
+	 *       the mlxbf_gige_ethtool_stats_keys[] array
+	 *
+	 * NOTE2: certain statistics below are zeroed upon
+	 *        port disable, so the calculation below
+	 *        must include the "cached" value of the stat
+	 *        plus the value read directly from hardware.
+	 *        Cached statistics are currently:
+	 *          rx_din_dropped_pkts
+	 *          rx_filter_passed_pkts
+	 *          rx_filter_discard_pkts
+	 */
+	*data++ = priv->stats.hw_access_errors;
+	*data++ = priv->stats.tx_invalid_checksums;
+	*data++ = priv->stats.tx_small_frames;
+	*data++ = priv->stats.tx_index_errors;
+	*data++ = priv->stats.sw_config_errors;
+	*data++ = priv->stats.sw_access_errors;
+	*data++ = priv->stats.rx_truncate_errors;
+	*data++ = priv->stats.rx_mac_errors;
+	*data++ = (priv->stats.rx_din_dropped_pkts +
+		   readq(priv->base + MLXBF_GIGE_RX_DIN_DROP_COUNTER));
+	*data++ = priv->stats.tx_fifo_full;
+	*data++ = (priv->stats.rx_filter_passed_pkts +
+		   readq(priv->base + MLXBF_GIGE_RX_PASS_COUNTER_ALL));
+	*data++ = (priv->stats.rx_filter_discard_pkts +
+		   readq(priv->base + MLXBF_GIGE_RX_DISC_COUNTER_ALL));
+}
+
+static void mlxbf_gige_get_pauseparam(struct net_device *netdev,
+				      struct ethtool_pauseparam *pause)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+
+	pause->autoneg = priv->aneg_pause;
+	pause->rx_pause = priv->rx_pause;
+	pause->tx_pause = priv->tx_pause;
+}
+
+const struct ethtool_ops mlxbf_gige_ethtool_ops = {
+	.get_link		= ethtool_op_get_link,
+	.get_ringparam		= mlxbf_gige_get_ringparam,
+	.get_regs_len           = mlxbf_gige_get_regs_len,
+	.get_regs               = mlxbf_gige_get_regs,
+	.get_strings            = mlxbf_gige_get_strings,
+	.get_sset_count         = mlxbf_gige_get_sset_count,
+	.get_ethtool_stats      = mlxbf_gige_get_ethtool_stats,
+	.nway_reset		= phy_ethtool_nway_reset,
+	.get_pauseparam		= mlxbf_gige_get_pauseparam,
+	.get_link_ksettings	= phy_ethtool_get_link_ksettings,
+};
+
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_gpio.c b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_gpio.c
new file mode 100644
index 000000000000..b549cec2ed41
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_gpio.c
@@ -0,0 +1,212 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+/* Initialize and handle GPIO interrupt triggered by INT_N PHY signal.
+ * This GPIO interrupt triggers the PHY state machine to bring the link
+ * up/down.
+ *
+ * Copyright (C) 2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#include <linux/acpi.h>
+#include <linux/bitfield.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/irqreturn.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+
+#include "mlxbf_gige.h"
+#include "mlxbf_gige_regs.h"
+
+#define MLXBF_GIGE_GPIO_CAUSE_FALL_EN		0x48
+#define MLXBF_GIGE_GPIO_CAUSE_OR_CAUSE_EVTEN0	0x80
+#define MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0		0x94
+#define MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE	0x98
+
+static void mlxbf_gige_gpio_enable(struct mlxbf_gige *priv)
+{
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&priv->gpio_lock, flags);
+	val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE);
+	val |= priv->phy_int_gpio_mask;
+	writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE);
+
+	/* The INT_N interrupt level is active low.
+	 * So enable cause fall bit to detect when GPIO
+	 * state goes low.
+	 */
+	val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_FALL_EN);
+	val |= priv->phy_int_gpio_mask;
+	writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_FALL_EN);
+
+	/* Enable PHY interrupt by setting the priority level */
+	val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0);
+	val |= priv->phy_int_gpio_mask;
+	writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0);
+	spin_unlock_irqrestore(&priv->gpio_lock, flags);
+}
+
+static void mlxbf_gige_gpio_disable(struct mlxbf_gige *priv)
+{
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&priv->gpio_lock, flags);
+	val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0);
+	val &= ~priv->phy_int_gpio_mask;
+	writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0);
+	spin_unlock_irqrestore(&priv->gpio_lock, flags);
+}
+
+static irqreturn_t mlxbf_gige_gpio_handler(int irq, void *ptr)
+{
+	struct mlxbf_gige *priv;
+	u32 val;
+
+	priv = ptr;
+
+	/* Check if this interrupt is from PHY device.
+	 * Return if it is not.
+	 */
+	val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CAUSE_EVTEN0);
+	if (!(val & priv->phy_int_gpio_mask))
+		return IRQ_NONE;
+
+	/* Clear interrupt when done, otherwise, no further interrupt
+	 * will be triggered.
+	 */
+	val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE);
+	val |= priv->phy_int_gpio_mask;
+	writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE);
+
+	generic_handle_irq(priv->phy_irq);
+
+	return IRQ_HANDLED;
+}
+
+static void mlxbf_gige_gpio_mask(struct irq_data *irqd)
+{
+	struct mlxbf_gige *priv = irq_data_get_irq_chip_data(irqd);
+
+	mlxbf_gige_gpio_disable(priv);
+}
+
+static void mlxbf_gige_gpio_unmask(struct irq_data *irqd)
+{
+	struct mlxbf_gige *priv = irq_data_get_irq_chip_data(irqd);
+
+	mlxbf_gige_gpio_enable(priv);
+}
+
+static struct irq_chip mlxbf_gige_gpio_chip = {
+	.name			= "mlxbf_gige_phy",
+	.irq_mask		= mlxbf_gige_gpio_mask,
+	.irq_unmask		= mlxbf_gige_gpio_unmask,
+};
+
+static int mlxbf_gige_gpio_domain_map(struct irq_domain *d,
+				      unsigned int irq,
+				      irq_hw_number_t hwirq)
+{
+	irq_set_chip_data(irq, d->host_data);
+	irq_set_chip_and_handler(irq, &mlxbf_gige_gpio_chip, handle_simple_irq);
+	irq_set_noprobe(irq);
+
+	return 0;
+}
+
+static const struct irq_domain_ops mlxbf_gige_gpio_domain_ops = {
+	.map    = mlxbf_gige_gpio_domain_map,
+	.xlate	= irq_domain_xlate_twocell,
+};
+
+#ifdef CONFIG_ACPI
+static int mlxbf_gige_gpio_resources(struct acpi_resource *ares,
+				     void *data)
+{
+	struct acpi_resource_gpio *gpio;
+	u32 *phy_int_gpio = data;
+
+	if (ares->type == ACPI_RESOURCE_TYPE_GPIO) {
+		gpio = &ares->data.gpio;
+		*phy_int_gpio = gpio->pin_table[0];
+	}
+
+	return 1;
+}
+#endif
+
+void mlxbf_gige_gpio_free(struct mlxbf_gige *priv)
+{
+	irq_dispose_mapping(priv->phy_irq);
+	irq_domain_remove(priv->irqdomain);
+}
+
+int mlxbf_gige_gpio_init(struct platform_device *pdev,
+			 struct mlxbf_gige *priv)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	u32 phy_int_gpio = 0;
+	int ret;
+
+	LIST_HEAD(resources);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, MLXBF_GIGE_RES_GPIO0);
+	if (!res)
+		return -ENODEV;
+
+	priv->gpio_io = devm_ioremap(dev, res->start, resource_size(res));
+	if (!priv->gpio_io)
+		return -ENOMEM;
+
+#ifdef CONFIG_ACPI
+	ret = acpi_dev_get_resources(ACPI_COMPANION(dev),
+				     &resources, mlxbf_gige_gpio_resources,
+				     &phy_int_gpio);
+	acpi_dev_free_resource_list(&resources);
+	if (ret < 0 || !phy_int_gpio) {
+		dev_err(dev, "Error retrieving the gpio phy pin");
+		return -EINVAL;
+	}
+#endif
+
+	priv->phy_int_gpio_mask = BIT(phy_int_gpio);
+
+	mlxbf_gige_gpio_disable(priv);
+
+	priv->hw_phy_irq = platform_get_irq(pdev, MLXBF_GIGE_PHY_INT_N);
+
+	priv->irqdomain = irq_domain_add_simple(NULL, 1, 0,
+						&mlxbf_gige_gpio_domain_ops,
+						priv);
+	if (!priv->irqdomain) {
+		dev_err(dev, "Failed to add IRQ domain\n");
+		return -ENOMEM;
+	}
+
+	priv->phy_irq = irq_create_mapping(priv->irqdomain, 0);
+	if (!priv->phy_irq) {
+		irq_domain_remove(priv->irqdomain);
+		priv->irqdomain = NULL;
+		dev_err(dev, "Error mapping PHY IRQ\n");
+		return -EINVAL;
+	}
+
+	ret = devm_request_irq(dev, priv->hw_phy_irq, mlxbf_gige_gpio_handler,
+			       IRQF_ONESHOT | IRQF_SHARED, "mlxbf_gige_phy", priv);
+	if (ret) {
+		dev_err(dev, "Failed to request PHY IRQ");
+		mlxbf_gige_gpio_free(priv);
+		return ret;
+	}
+
+	return ret;
+}
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_intr.c b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_intr.c
new file mode 100644
index 000000000000..c63a74d730f8
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_intr.c
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+/* Interrupt related logic for Mellanox Gigabit Ethernet driver
+ *
+ * Copyright (C) 2020-2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#include <linux/interrupt.h>
+
+#include "mlxbf_gige.h"
+#include "mlxbf_gige_regs.h"
+
+static irqreturn_t mlxbf_gige_error_intr(int irq, void *dev_id)
+{
+	struct mlxbf_gige *priv;
+	u64 int_status;
+
+	priv = dev_id;
+
+	priv->error_intr_count++;
+
+	int_status = readq(priv->base + MLXBF_GIGE_INT_STATUS);
+
+	if (int_status & MLXBF_GIGE_INT_STATUS_HW_ACCESS_ERROR)
+		priv->stats.hw_access_errors++;
+
+	if (int_status & MLXBF_GIGE_INT_STATUS_TX_CHECKSUM_INPUTS) {
+		priv->stats.tx_invalid_checksums++;
+		/* This error condition is latched into MLXBF_GIGE_INT_STATUS
+		 * when the GigE silicon operates on the offending
+		 * TX WQE. The write to MLXBF_GIGE_INT_STATUS at the bottom
+		 * of this routine clears this error condition.
+		 */
+	}
+
+	if (int_status & MLXBF_GIGE_INT_STATUS_TX_SMALL_FRAME_SIZE) {
+		priv->stats.tx_small_frames++;
+		/* This condition happens when the networking stack invokes
+		 * this driver's "start_xmit()" method with a packet whose
+		 * size < 60 bytes.  The GigE silicon will automatically pad
+		 * this small frame up to a minimum-sized frame before it is
+		 * sent. The "tx_small_frame" condition is latched into the
+		 * MLXBF_GIGE_INT_STATUS register when the GigE silicon
+		 * operates on the offending TX WQE. The write to
+		 * MLXBF_GIGE_INT_STATUS at the bottom of this routine
+		 * clears this condition.
+		 */
+	}
+
+	if (int_status & MLXBF_GIGE_INT_STATUS_TX_PI_CI_EXCEED_WQ_SIZE)
+		priv->stats.tx_index_errors++;
+
+	if (int_status & MLXBF_GIGE_INT_STATUS_SW_CONFIG_ERROR)
+		priv->stats.sw_config_errors++;
+
+	if (int_status & MLXBF_GIGE_INT_STATUS_SW_ACCESS_ERROR)
+		priv->stats.sw_access_errors++;
+
+	/* Clear all error interrupts by writing '1' back to
+	 * all the asserted bits in INT_STATUS.  Do not write
+	 * '1' back to 'receive packet' bit, since that is
+	 * managed separately.
+	 */
+
+	int_status &= ~MLXBF_GIGE_INT_STATUS_RX_RECEIVE_PACKET;
+
+	writeq(int_status, priv->base + MLXBF_GIGE_INT_STATUS);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mlxbf_gige_rx_intr(int irq, void *dev_id)
+{
+	struct mlxbf_gige *priv;
+
+	priv = dev_id;
+
+	priv->rx_intr_count++;
+
+	/* NOTE: GigE silicon automatically disables "packet rx" interrupt by
+	 *       setting MLXBF_GIGE_INT_MASK bit0 upon triggering the interrupt
+	 *       to the ARM cores.  Software needs to re-enable "packet rx"
+	 *       interrupts by clearing MLXBF_GIGE_INT_MASK bit0.
+	 */
+
+	napi_schedule(&priv->napi);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mlxbf_gige_llu_plu_intr(int irq, void *dev_id)
+{
+	struct mlxbf_gige *priv;
+
+	priv = dev_id;
+	priv->llu_plu_intr_count++;
+
+	return IRQ_HANDLED;
+}
+
+int mlxbf_gige_request_irqs(struct mlxbf_gige *priv)
+{
+	int err;
+
+	err = request_irq(priv->error_irq, mlxbf_gige_error_intr, 0,
+			  "mlxbf_gige_error", priv);
+	if (err) {
+		dev_err(priv->dev, "Request error_irq failure\n");
+		return err;
+	}
+
+	err = request_irq(priv->rx_irq, mlxbf_gige_rx_intr, 0,
+			  "mlxbf_gige_rx", priv);
+	if (err) {
+		dev_err(priv->dev, "Request rx_irq failure\n");
+		goto free_error_irq;
+	}
+
+	err = request_irq(priv->llu_plu_irq, mlxbf_gige_llu_plu_intr, 0,
+			  "mlxbf_gige_llu_plu", priv);
+	if (err) {
+		dev_err(priv->dev, "Request llu_plu_irq failure\n");
+		goto free_rx_irq;
+	}
+
+	return 0;
+
+free_rx_irq:
+	free_irq(priv->rx_irq, priv);
+
+free_error_irq:
+	free_irq(priv->error_irq, priv);
+
+	return err;
+}
+
+void mlxbf_gige_free_irqs(struct mlxbf_gige *priv)
+{
+	free_irq(priv->error_irq, priv);
+	free_irq(priv->rx_irq, priv);
+	free_irq(priv->llu_plu_irq, priv);
+}
+
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c
new file mode 100644
index 000000000000..1246d7ca89f8
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c
@@ -0,0 +1,459 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+/* Gigabit Ethernet driver for Mellanox BlueField SoC
+ *
+ * Copyright (C) 2020-2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#include <linux/acpi.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/etherdevice.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/skbuff.h>
+
+#include "mlxbf_gige.h"
+#include "mlxbf_gige_regs.h"
+
+#define DRV_NAME    "mlxbf_gige"
+
+/* Allocate SKB whose payload pointer aligns with the Bluefield
+ * hardware DMA limitation, i.e. DMA operation can't cross
+ * a 4KB boundary.  A maximum packet size of 2KB is assumed in the
+ * alignment formula.  The alignment logic overallocates an SKB,
+ * and then adjusts the headroom so that the SKB data pointer is
+ * naturally aligned to a 2KB boundary.
+ */
+struct sk_buff *mlxbf_gige_alloc_skb(struct mlxbf_gige *priv,
+				     unsigned int map_len,
+				     dma_addr_t *buf_dma,
+				     enum dma_data_direction dir)
+{
+	struct sk_buff *skb;
+	u64 addr, offset;
+
+	/* Overallocate the SKB so that any headroom adjustment (to
+	 * provide 2KB natural alignment) does not exceed payload area
+	 */
+	skb = netdev_alloc_skb(priv->netdev, MLXBF_GIGE_DEFAULT_BUF_SZ * 2);
+	if (!skb)
+		return NULL;
+
+	/* Adjust the headroom so that skb->data is naturally aligned to
+	 * a 2KB boundary, which is the maximum packet size supported.
+	 */
+	addr = (long)skb->data;
+	offset = (addr + MLXBF_GIGE_DEFAULT_BUF_SZ - 1) &
+		~(MLXBF_GIGE_DEFAULT_BUF_SZ - 1);
+	offset -= addr;
+	if (offset)
+		skb_reserve(skb, offset);
+
+	/* Return streaming DMA mapping to caller */
+	*buf_dma = dma_map_single(priv->dev, skb->data, map_len, dir);
+	if (dma_mapping_error(priv->dev, *buf_dma)) {
+		dev_kfree_skb(skb);
+		*buf_dma = (dma_addr_t)0;
+		return NULL;
+	}
+
+	return skb;
+}
+
+static void mlxbf_gige_initial_mac(struct mlxbf_gige *priv)
+{
+	u8 mac[ETH_ALEN];
+	u64 local_mac;
+
+	memset(mac, 0, ETH_ALEN);
+	mlxbf_gige_get_mac_rx_filter(priv, MLXBF_GIGE_LOCAL_MAC_FILTER_IDX,
+				     &local_mac);
+	u64_to_ether_addr(local_mac, mac);
+
+	if (is_valid_ether_addr(mac)) {
+		ether_addr_copy(priv->netdev->dev_addr, mac);
+	} else {
+		/* Provide a random MAC if for some reason the device has
+		 * not been configured with a valid MAC address already.
+		 */
+		eth_hw_addr_random(priv->netdev);
+	}
+
+	local_mac = ether_addr_to_u64(priv->netdev->dev_addr);
+	mlxbf_gige_set_mac_rx_filter(priv, MLXBF_GIGE_LOCAL_MAC_FILTER_IDX,
+				     local_mac);
+}
+
+static void mlxbf_gige_cache_stats(struct mlxbf_gige *priv)
+{
+	struct mlxbf_gige_stats *p;
+
+	/* Cache stats that will be cleared by clean port operation */
+	p = &priv->stats;
+	p->rx_din_dropped_pkts += readq(priv->base +
+					MLXBF_GIGE_RX_DIN_DROP_COUNTER);
+	p->rx_filter_passed_pkts += readq(priv->base +
+					  MLXBF_GIGE_RX_PASS_COUNTER_ALL);
+	p->rx_filter_discard_pkts += readq(priv->base +
+					   MLXBF_GIGE_RX_DISC_COUNTER_ALL);
+}
+
+static int mlxbf_gige_clean_port(struct mlxbf_gige *priv)
+{
+	u64 control;
+	u64 temp;
+	int err;
+
+	/* Set the CLEAN_PORT_EN bit to trigger SW reset */
+	control = readq(priv->base + MLXBF_GIGE_CONTROL);
+	control |= MLXBF_GIGE_CONTROL_CLEAN_PORT_EN;
+	writeq(control, priv->base + MLXBF_GIGE_CONTROL);
+
+	/* Ensure completion of "clean port" write before polling status */
+	mb();
+
+	err = readq_poll_timeout_atomic(priv->base + MLXBF_GIGE_STATUS, temp,
+					(temp & MLXBF_GIGE_STATUS_READY),
+					100, 100000);
+
+	/* Clear the CLEAN_PORT_EN bit at end of this loop */
+	control = readq(priv->base + MLXBF_GIGE_CONTROL);
+	control &= ~MLXBF_GIGE_CONTROL_CLEAN_PORT_EN;
+	writeq(control, priv->base + MLXBF_GIGE_CONTROL);
+
+	return err;
+}
+
+static int mlxbf_gige_open(struct net_device *netdev)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+	struct phy_device *phydev = netdev->phydev;
+	u64 int_en;
+	int err;
+
+	err = mlxbf_gige_request_irqs(priv);
+	if (err)
+		return err;
+	mlxbf_gige_cache_stats(priv);
+	err = mlxbf_gige_clean_port(priv);
+	if (err)
+		goto free_irqs;
+	err = mlxbf_gige_rx_init(priv);
+	if (err)
+		goto free_irqs;
+	err = mlxbf_gige_tx_init(priv);
+	if (err)
+		goto rx_deinit;
+
+	phy_start(phydev);
+
+	netif_napi_add(netdev, &priv->napi, mlxbf_gige_poll, NAPI_POLL_WEIGHT);
+	napi_enable(&priv->napi);
+	netif_start_queue(netdev);
+
+	/* Set bits in INT_EN that we care about */
+	int_en = MLXBF_GIGE_INT_EN_HW_ACCESS_ERROR |
+		 MLXBF_GIGE_INT_EN_TX_CHECKSUM_INPUTS |
+		 MLXBF_GIGE_INT_EN_TX_SMALL_FRAME_SIZE |
+		 MLXBF_GIGE_INT_EN_TX_PI_CI_EXCEED_WQ_SIZE |
+		 MLXBF_GIGE_INT_EN_SW_CONFIG_ERROR |
+		 MLXBF_GIGE_INT_EN_SW_ACCESS_ERROR |
+		 MLXBF_GIGE_INT_EN_RX_RECEIVE_PACKET;
+
+	/* Ensure completion of all initialization before enabling interrupts */
+	mb();
+
+	writeq(int_en, priv->base + MLXBF_GIGE_INT_EN);
+
+	return 0;
+
+rx_deinit:
+	mlxbf_gige_rx_deinit(priv);
+
+free_irqs:
+	mlxbf_gige_free_irqs(priv);
+	return err;
+}
+
+static int mlxbf_gige_stop(struct net_device *netdev)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+
+	writeq(0, priv->base + MLXBF_GIGE_INT_EN);
+	netif_stop_queue(netdev);
+	napi_disable(&priv->napi);
+	netif_napi_del(&priv->napi);
+	mlxbf_gige_free_irqs(priv);
+
+	phy_stop(netdev->phydev);
+
+	mlxbf_gige_rx_deinit(priv);
+	mlxbf_gige_tx_deinit(priv);
+	mlxbf_gige_cache_stats(priv);
+	mlxbf_gige_clean_port(priv);
+
+	return 0;
+}
+
+static int mlxbf_gige_do_ioctl(struct net_device *netdev,
+			       struct ifreq *ifr, int cmd)
+{
+	if (!(netif_running(netdev)))
+		return -EINVAL;
+
+	return phy_mii_ioctl(netdev->phydev, ifr, cmd);
+}
+
+static void mlxbf_gige_set_rx_mode(struct net_device *netdev)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+	bool new_promisc_enabled;
+
+	new_promisc_enabled = netdev->flags & IFF_PROMISC;
+
+	/* Only write to the hardware registers if the new setting
+	 * of promiscuous mode is different from the current one.
+	 */
+	if (new_promisc_enabled != priv->promisc_enabled) {
+		priv->promisc_enabled = new_promisc_enabled;
+
+		if (new_promisc_enabled)
+			mlxbf_gige_enable_promisc(priv);
+		else
+			mlxbf_gige_disable_promisc(priv);
+	}
+}
+
+static void mlxbf_gige_get_stats64(struct net_device *netdev,
+				   struct rtnl_link_stats64 *stats)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+
+	netdev_stats_to_stats64(stats, &netdev->stats);
+
+	stats->rx_length_errors = priv->stats.rx_truncate_errors;
+	stats->rx_fifo_errors = priv->stats.rx_din_dropped_pkts +
+				readq(priv->base + MLXBF_GIGE_RX_DIN_DROP_COUNTER);
+	stats->rx_crc_errors = priv->stats.rx_mac_errors;
+	stats->rx_errors = stats->rx_length_errors +
+			   stats->rx_fifo_errors +
+			   stats->rx_crc_errors;
+
+	stats->tx_fifo_errors = priv->stats.tx_fifo_full;
+	stats->tx_errors = stats->tx_fifo_errors;
+}
+
+static const struct net_device_ops mlxbf_gige_netdev_ops = {
+	.ndo_open		= mlxbf_gige_open,
+	.ndo_stop		= mlxbf_gige_stop,
+	.ndo_start_xmit		= mlxbf_gige_start_xmit,
+	.ndo_set_mac_address	= eth_mac_addr,
+	.ndo_validate_addr	= eth_validate_addr,
+	.ndo_do_ioctl		= mlxbf_gige_do_ioctl,
+	.ndo_set_rx_mode        = mlxbf_gige_set_rx_mode,
+	.ndo_get_stats64        = mlxbf_gige_get_stats64,
+};
+
+static void mlxbf_gige_adjust_link(struct net_device *netdev)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+	struct phy_device *phydev = netdev->phydev;
+
+	if (phydev->link) {
+		priv->rx_pause = phydev->pause;
+		priv->tx_pause = phydev->pause;
+	}
+
+	phy_print_status(phydev);
+}
+
+static int mlxbf_gige_probe(struct platform_device *pdev)
+{
+	struct phy_device *phydev;
+	struct net_device *netdev;
+	struct resource *mac_res;
+	struct resource *llu_res;
+	struct resource *plu_res;
+	struct mlxbf_gige *priv;
+	void __iomem *llu_base;
+	void __iomem *plu_base;
+	void __iomem *base;
+	u64 control;
+	int addr;
+	int err;
+
+	mac_res = platform_get_resource(pdev, IORESOURCE_MEM, MLXBF_GIGE_RES_MAC);
+	if (!mac_res)
+		return -ENXIO;
+
+	base = devm_ioremap_resource(&pdev->dev, mac_res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	llu_res = platform_get_resource(pdev, IORESOURCE_MEM, MLXBF_GIGE_RES_LLU);
+	if (!llu_res)
+		return -ENXIO;
+
+	llu_base = devm_ioremap_resource(&pdev->dev, llu_res);
+	if (IS_ERR(llu_base))
+		return PTR_ERR(llu_base);
+
+	plu_res = platform_get_resource(pdev, IORESOURCE_MEM, MLXBF_GIGE_RES_PLU);
+	if (!plu_res)
+		return -ENXIO;
+
+	plu_base = devm_ioremap_resource(&pdev->dev, plu_res);
+	if (IS_ERR(plu_base))
+		return PTR_ERR(plu_base);
+
+	/* Perform general init of GigE block */
+	control = readq(base + MLXBF_GIGE_CONTROL);
+	control |= MLXBF_GIGE_CONTROL_PORT_EN;
+	writeq(control, base + MLXBF_GIGE_CONTROL);
+
+	netdev = devm_alloc_etherdev(&pdev->dev, sizeof(*priv));
+	if (!netdev)
+		return -ENOMEM;
+
+	SET_NETDEV_DEV(netdev, &pdev->dev);
+	netdev->netdev_ops = &mlxbf_gige_netdev_ops;
+	netdev->ethtool_ops = &mlxbf_gige_ethtool_ops;
+	priv = netdev_priv(netdev);
+	priv->netdev = netdev;
+
+	platform_set_drvdata(pdev, priv);
+	priv->dev = &pdev->dev;
+	priv->pdev = pdev;
+
+	spin_lock_init(&priv->lock);
+	spin_lock_init(&priv->gpio_lock);
+
+	/* Attach MDIO device */
+	err = mlxbf_gige_mdio_probe(pdev, priv);
+	if (err)
+		return err;
+
+	err = mlxbf_gige_gpio_init(pdev, priv);
+	if (err) {
+		dev_err(&pdev->dev, "PHY IRQ initialization failed\n");
+		mlxbf_gige_mdio_remove(priv);
+		return -ENODEV;
+	}
+
+	priv->base = base;
+	priv->llu_base = llu_base;
+	priv->plu_base = plu_base;
+
+	priv->rx_q_entries = MLXBF_GIGE_DEFAULT_RXQ_SZ;
+	priv->tx_q_entries = MLXBF_GIGE_DEFAULT_TXQ_SZ;
+
+	/* Write initial MAC address to hardware */
+	mlxbf_gige_initial_mac(priv);
+
+	err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+	if (err) {
+		dev_err(&pdev->dev, "DMA configuration failed: 0x%x\n", err);
+		goto out;
+	}
+
+	priv->error_irq = platform_get_irq(pdev, MLXBF_GIGE_ERROR_INTR_IDX);
+	priv->rx_irq = platform_get_irq(pdev, MLXBF_GIGE_RECEIVE_PKT_INTR_IDX);
+	priv->llu_plu_irq = platform_get_irq(pdev, MLXBF_GIGE_LLU_PLU_INTR_IDX);
+
+	phydev = phy_find_first(priv->mdiobus);
+	if (!phydev) {
+		err = -ENODEV;
+		goto out;
+	}
+
+	addr = phydev->mdio.addr;
+	phydev->irq = priv->mdiobus->irq[addr] = priv->phy_irq;
+
+	err = phy_connect_direct(netdev, phydev,
+				 mlxbf_gige_adjust_link,
+				 PHY_INTERFACE_MODE_GMII);
+	if (err) {
+		dev_err(&pdev->dev, "Could not attach to PHY\n");
+		goto out;
+	}
+
+	/* MAC only supports 1000T full duplex mode */
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_100baseT_Full_BIT);
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Full_BIT);
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+
+	/* MAC supports symmetric flow control */
+	phy_support_sym_pause(phydev);
+
+	/* Initialise pause frame settings */
+	priv->rx_pause = 0;
+	priv->tx_pause = 0;
+	priv->aneg_pause = AUTONEG_ENABLE;
+
+	/* Display information about attached PHY device */
+	phy_attached_info(phydev);
+
+	err = register_netdev(netdev);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to register netdev\n");
+		phy_disconnect(phydev);
+		goto out;
+	}
+
+	return 0;
+
+out:
+	mlxbf_gige_gpio_free(priv);
+	mlxbf_gige_mdio_remove(priv);
+	return err;
+}
+
+static int mlxbf_gige_remove(struct platform_device *pdev)
+{
+	struct mlxbf_gige *priv = platform_get_drvdata(pdev);
+
+	unregister_netdev(priv->netdev);
+	phy_disconnect(priv->netdev->phydev);
+	mlxbf_gige_gpio_free(priv);
+	mlxbf_gige_mdio_remove(priv);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static void mlxbf_gige_shutdown(struct platform_device *pdev)
+{
+	struct mlxbf_gige *priv = platform_get_drvdata(pdev);
+
+	writeq(0, priv->base + MLXBF_GIGE_INT_EN);
+	mlxbf_gige_clean_port(priv);
+}
+
+static const struct acpi_device_id mlxbf_gige_acpi_match[] = {
+	{ "MLNXBF17", 0 },
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, mlxbf_gige_acpi_match);
+
+static struct platform_driver mlxbf_gige_driver = {
+	.probe = mlxbf_gige_probe,
+	.remove = mlxbf_gige_remove,
+	.shutdown = mlxbf_gige_shutdown,
+	.driver = {
+		.name = DRV_NAME,
+		.acpi_match_table = ACPI_PTR(mlxbf_gige_acpi_match),
+	},
+};
+
+module_platform_driver(mlxbf_gige_driver);
+
+MODULE_DESCRIPTION("Mellanox BlueField SoC Gigabit Ethernet Driver");
+MODULE_AUTHOR("David Thompson <davthompson@nvidia.com>");
+MODULE_AUTHOR("Asmaa Mnebhi <asmaa@nvidia.com>");
+MODULE_LICENSE("Dual BSD/GPL");
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_mdio.c b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_mdio.c
new file mode 100644
index 000000000000..d1643177ad8a
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_mdio.c
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+/* MDIO support for Mellanox Gigabit Ethernet driver
+ *
+ * Copyright (C) 2020-2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#include <linux/acpi.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/ioport.h>
+#include <linux/irqreturn.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+
+#include "mlxbf_gige.h"
+
+#define MLXBF_GIGE_MDIO_GW_OFFSET	0x0
+#define MLXBF_GIGE_MDIO_CFG_OFFSET	0x4
+
+/* Support clause 22 */
+#define MLXBF_GIGE_MDIO_CL22_ST1	0x1
+#define MLXBF_GIGE_MDIO_CL22_WRITE	0x1
+#define MLXBF_GIGE_MDIO_CL22_READ	0x2
+
+/* Busy bit is set by software and cleared by hardware */
+#define MLXBF_GIGE_MDIO_SET_BUSY	0x1
+
+/* MDIO GW register bits */
+#define MLXBF_GIGE_MDIO_GW_AD_MASK	GENMASK(15, 0)
+#define MLXBF_GIGE_MDIO_GW_DEVAD_MASK	GENMASK(20, 16)
+#define MLXBF_GIGE_MDIO_GW_PARTAD_MASK	GENMASK(25, 21)
+#define MLXBF_GIGE_MDIO_GW_OPCODE_MASK	GENMASK(27, 26)
+#define MLXBF_GIGE_MDIO_GW_ST1_MASK	GENMASK(28, 28)
+#define MLXBF_GIGE_MDIO_GW_BUSY_MASK	GENMASK(30, 30)
+
+/* MDIO config register bits */
+#define MLXBF_GIGE_MDIO_CFG_MDIO_MODE_MASK		GENMASK(1, 0)
+#define MLXBF_GIGE_MDIO_CFG_MDIO3_3_MASK		GENMASK(2, 2)
+#define MLXBF_GIGE_MDIO_CFG_MDIO_FULL_DRIVE_MASK	GENMASK(4, 4)
+#define MLXBF_GIGE_MDIO_CFG_MDC_PERIOD_MASK		GENMASK(15, 8)
+#define MLXBF_GIGE_MDIO_CFG_MDIO_IN_SAMP_MASK		GENMASK(23, 16)
+#define MLXBF_GIGE_MDIO_CFG_MDIO_OUT_SAMP_MASK		GENMASK(31, 24)
+
+/* Formula for encoding the MDIO period. The encoded value is
+ * passed to the MDIO config register.
+ *
+ * mdc_clk = 2*(val + 1)*i1clk
+ *
+ * 400 ns = 2*(val + 1)*(((1/430)*1000) ns)
+ *
+ * val = (((400 * 430 / 1000) / 2) - 1)
+ */
+#define MLXBF_GIGE_I1CLK_MHZ		430
+#define MLXBF_GIGE_MDC_CLK_NS		400
+
+#define MLXBF_GIGE_MDIO_PERIOD	(((MLXBF_GIGE_MDC_CLK_NS * MLXBF_GIGE_I1CLK_MHZ / 1000) / 2) - 1)
+
+#define MLXBF_GIGE_MDIO_CFG_VAL (FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_MODE_MASK, 1) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO3_3_MASK, 1) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_FULL_DRIVE_MASK, 1) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDC_PERIOD_MASK, \
+					    MLXBF_GIGE_MDIO_PERIOD) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_IN_SAMP_MASK, 6) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_OUT_SAMP_MASK, 13))
+
+static u32 mlxbf_gige_mdio_create_cmd(u16 data, int phy_add,
+				      int phy_reg, u32 opcode)
+{
+	u32 gw_reg = 0;
+
+	gw_reg |= FIELD_PREP(MLXBF_GIGE_MDIO_GW_AD_MASK, data);
+	gw_reg |= FIELD_PREP(MLXBF_GIGE_MDIO_GW_DEVAD_MASK, phy_reg);
+	gw_reg |= FIELD_PREP(MLXBF_GIGE_MDIO_GW_PARTAD_MASK, phy_add);
+	gw_reg |= FIELD_PREP(MLXBF_GIGE_MDIO_GW_OPCODE_MASK, opcode);
+	gw_reg |= FIELD_PREP(MLXBF_GIGE_MDIO_GW_ST1_MASK,
+			     MLXBF_GIGE_MDIO_CL22_ST1);
+	gw_reg |= FIELD_PREP(MLXBF_GIGE_MDIO_GW_BUSY_MASK,
+			     MLXBF_GIGE_MDIO_SET_BUSY);
+
+	return gw_reg;
+}
+
+static int mlxbf_gige_mdio_read(struct mii_bus *bus, int phy_add, int phy_reg)
+{
+	struct mlxbf_gige *priv = bus->priv;
+	u32 cmd;
+	int ret;
+	u32 val;
+
+	if (phy_reg & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
+	/* Send mdio read request */
+	cmd = mlxbf_gige_mdio_create_cmd(0, phy_add, phy_reg, MLXBF_GIGE_MDIO_CL22_READ);
+
+	writel(cmd, priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET);
+
+	ret = readl_poll_timeout_atomic(priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET,
+					val, !(val & MLXBF_GIGE_MDIO_GW_BUSY_MASK), 100, 1000000);
+
+	if (ret) {
+		writel(0, priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET);
+		return ret;
+	}
+
+	ret = readl(priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET);
+	/* Only return ad bits of the gw register */
+	ret &= MLXBF_GIGE_MDIO_GW_AD_MASK;
+
+	return ret;
+}
+
+static int mlxbf_gige_mdio_write(struct mii_bus *bus, int phy_add,
+				 int phy_reg, u16 val)
+{
+	struct mlxbf_gige *priv = bus->priv;
+	u32 cmd;
+	int ret;
+	u32 temp;
+
+	if (phy_reg & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
+	/* Send mdio write request */
+	cmd = mlxbf_gige_mdio_create_cmd(val, phy_add, phy_reg,
+					 MLXBF_GIGE_MDIO_CL22_WRITE);
+	writel(cmd, priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET);
+
+	/* If the poll timed out, drop the request */
+	ret = readl_poll_timeout_atomic(priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET,
+					temp, !(temp & MLXBF_GIGE_MDIO_GW_BUSY_MASK), 100, 1000000);
+
+	return ret;
+}
+
+int mlxbf_gige_mdio_probe(struct platform_device *pdev, struct mlxbf_gige *priv)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int ret;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, MLXBF_GIGE_RES_MDIO9);
+	if (!res)
+		return -ENODEV;
+
+	priv->mdio_io = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->mdio_io))
+		return PTR_ERR(priv->mdio_io);
+
+	/* Configure mdio parameters */
+	writel(MLXBF_GIGE_MDIO_CFG_VAL,
+	       priv->mdio_io + MLXBF_GIGE_MDIO_CFG_OFFSET);
+
+	priv->mdiobus = devm_mdiobus_alloc(dev);
+	if (!priv->mdiobus) {
+		dev_err(dev, "Failed to alloc MDIO bus\n");
+		return -ENOMEM;
+	}
+
+	priv->mdiobus->name = "mlxbf-mdio";
+	priv->mdiobus->read = mlxbf_gige_mdio_read;
+	priv->mdiobus->write = mlxbf_gige_mdio_write;
+	priv->mdiobus->parent = dev;
+	priv->mdiobus->priv = priv;
+	snprintf(priv->mdiobus->id, MII_BUS_ID_SIZE, "%s",
+		 dev_name(dev));
+
+	ret = mdiobus_register(priv->mdiobus);
+	if (ret)
+		dev_err(dev, "Failed to register MDIO bus\n");
+
+	return ret;
+}
+
+void mlxbf_gige_mdio_remove(struct mlxbf_gige *priv)
+{
+	mdiobus_unregister(priv->mdiobus);
+}
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h
new file mode 100644
index 000000000000..d4652f9ce225
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h
@@ -0,0 +1,78 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause */
+
+/* Header file for Mellanox BlueField GigE register defines
+ *
+ * Copyright (C) 2020-2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#ifndef __MLXBF_GIGE_REGS_H__
+#define __MLXBF_GIGE_REGS_H__
+
+#define MLXBF_GIGE_STATUS                             0x0010
+#define MLXBF_GIGE_STATUS_READY                       BIT(0)
+#define MLXBF_GIGE_INT_STATUS                         0x0028
+#define MLXBF_GIGE_INT_STATUS_RX_RECEIVE_PACKET       BIT(0)
+#define MLXBF_GIGE_INT_STATUS_RX_MAC_ERROR            BIT(1)
+#define MLXBF_GIGE_INT_STATUS_RX_TRN_ERROR            BIT(2)
+#define MLXBF_GIGE_INT_STATUS_SW_ACCESS_ERROR         BIT(3)
+#define MLXBF_GIGE_INT_STATUS_SW_CONFIG_ERROR         BIT(4)
+#define MLXBF_GIGE_INT_STATUS_TX_PI_CI_EXCEED_WQ_SIZE BIT(5)
+#define MLXBF_GIGE_INT_STATUS_TX_SMALL_FRAME_SIZE     BIT(6)
+#define MLXBF_GIGE_INT_STATUS_TX_CHECKSUM_INPUTS      BIT(7)
+#define MLXBF_GIGE_INT_STATUS_HW_ACCESS_ERROR         BIT(8)
+#define MLXBF_GIGE_INT_EN                             0x0030
+#define MLXBF_GIGE_INT_EN_RX_RECEIVE_PACKET           BIT(0)
+#define MLXBF_GIGE_INT_EN_RX_MAC_ERROR                BIT(1)
+#define MLXBF_GIGE_INT_EN_RX_TRN_ERROR                BIT(2)
+#define MLXBF_GIGE_INT_EN_SW_ACCESS_ERROR             BIT(3)
+#define MLXBF_GIGE_INT_EN_SW_CONFIG_ERROR             BIT(4)
+#define MLXBF_GIGE_INT_EN_TX_PI_CI_EXCEED_WQ_SIZE     BIT(5)
+#define MLXBF_GIGE_INT_EN_TX_SMALL_FRAME_SIZE         BIT(6)
+#define MLXBF_GIGE_INT_EN_TX_CHECKSUM_INPUTS          BIT(7)
+#define MLXBF_GIGE_INT_EN_HW_ACCESS_ERROR             BIT(8)
+#define MLXBF_GIGE_INT_MASK                           0x0038
+#define MLXBF_GIGE_INT_MASK_RX_RECEIVE_PACKET         BIT(0)
+#define MLXBF_GIGE_CONTROL                            0x0040
+#define MLXBF_GIGE_CONTROL_PORT_EN                    BIT(0)
+#define MLXBF_GIGE_CONTROL_MAC_ID_RANGE_EN            BIT(1)
+#define MLXBF_GIGE_CONTROL_EN_SPECIFIC_MAC            BIT(4)
+#define MLXBF_GIGE_CONTROL_CLEAN_PORT_EN              BIT(31)
+#define MLXBF_GIGE_RX_WQ_BASE                         0x0200
+#define MLXBF_GIGE_RX_WQE_SIZE_LOG2                   0x0208
+#define MLXBF_GIGE_RX_WQE_SIZE_LOG2_RESET_VAL         7
+#define MLXBF_GIGE_RX_CQ_BASE                         0x0210
+#define MLXBF_GIGE_TX_WQ_BASE                         0x0218
+#define MLXBF_GIGE_TX_WQ_SIZE_LOG2                    0x0220
+#define MLXBF_GIGE_TX_WQ_SIZE_LOG2_RESET_VAL          7
+#define MLXBF_GIGE_TX_CI_UPDATE_ADDRESS               0x0228
+#define MLXBF_GIGE_RX_WQE_PI                          0x0230
+#define MLXBF_GIGE_TX_PRODUCER_INDEX                  0x0238
+#define MLXBF_GIGE_RX_MAC_FILTER                      0x0240
+#define MLXBF_GIGE_RX_MAC_FILTER_STRIDE               0x0008
+#define MLXBF_GIGE_RX_DIN_DROP_COUNTER                0x0260
+#define MLXBF_GIGE_TX_CONSUMER_INDEX                  0x0310
+#define MLXBF_GIGE_TX_CONTROL                         0x0318
+#define MLXBF_GIGE_TX_CONTROL_GRACEFUL_STOP           BIT(0)
+#define MLXBF_GIGE_TX_STATUS                          0x0388
+#define MLXBF_GIGE_TX_STATUS_DATA_FIFO_FULL           BIT(1)
+#define MLXBF_GIGE_RX_MAC_FILTER_DMAC_RANGE_START     0x0520
+#define MLXBF_GIGE_RX_MAC_FILTER_DMAC_RANGE_END       0x0528
+#define MLXBF_GIGE_RX_MAC_FILTER_COUNT_DISC           0x0540
+#define MLXBF_GIGE_RX_MAC_FILTER_COUNT_DISC_EN        BIT(0)
+#define MLXBF_GIGE_RX_MAC_FILTER_COUNT_PASS           0x0548
+#define MLXBF_GIGE_RX_MAC_FILTER_COUNT_PASS_EN        BIT(0)
+#define MLXBF_GIGE_RX_PASS_COUNTER_ALL                0x0550
+#define MLXBF_GIGE_RX_DISC_COUNTER_ALL                0x0560
+#define MLXBF_GIGE_RX                                 0x0578
+#define MLXBF_GIGE_RX_STRIP_CRC_EN                    BIT(1)
+#define MLXBF_GIGE_RX_DMA                             0x0580
+#define MLXBF_GIGE_RX_DMA_EN                          BIT(0)
+#define MLXBF_GIGE_RX_CQE_PACKET_CI                   0x05b0
+#define MLXBF_GIGE_MAC_CFG                            0x05e8
+
+/* NOTE: MLXBF_GIGE_MAC_CFG is the last defined register offset,
+ * so use that plus size of single register to derive total size
+ */
+#define MLXBF_GIGE_MMIO_REG_SZ                        (MLXBF_GIGE_MAC_CFG + 8)
+
+#endif /* !defined(__MLXBF_GIGE_REGS_H__) */
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_rx.c b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_rx.c
new file mode 100644
index 000000000000..c6dbd4f035d1
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_rx.c
@@ -0,0 +1,318 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+/* Packet receive logic for Mellanox Gigabit Ethernet driver
+ *
+ * Copyright (C) 2020-2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+
+#include "mlxbf_gige.h"
+#include "mlxbf_gige_regs.h"
+
+void mlxbf_gige_set_mac_rx_filter(struct mlxbf_gige *priv,
+				  unsigned int index, u64 dmac)
+{
+	void __iomem *base = priv->base;
+	u64 control;
+
+	/* Write destination MAC to specified MAC RX filter */
+	writeq(dmac, base + MLXBF_GIGE_RX_MAC_FILTER +
+	       (index * MLXBF_GIGE_RX_MAC_FILTER_STRIDE));
+
+	/* Enable MAC receive filter mask for specified index */
+	control = readq(base + MLXBF_GIGE_CONTROL);
+	control |= (MLXBF_GIGE_CONTROL_EN_SPECIFIC_MAC << index);
+	writeq(control, base + MLXBF_GIGE_CONTROL);
+}
+
+void mlxbf_gige_get_mac_rx_filter(struct mlxbf_gige *priv,
+				  unsigned int index, u64 *dmac)
+{
+	void __iomem *base = priv->base;
+
+	/* Read destination MAC from specified MAC RX filter */
+	*dmac = readq(base + MLXBF_GIGE_RX_MAC_FILTER +
+		      (index * MLXBF_GIGE_RX_MAC_FILTER_STRIDE));
+}
+
+void mlxbf_gige_enable_promisc(struct mlxbf_gige *priv)
+{
+	void __iomem *base = priv->base;
+	u64 control;
+
+	/* Enable MAC_ID_RANGE match functionality */
+	control = readq(base + MLXBF_GIGE_CONTROL);
+	control |= MLXBF_GIGE_CONTROL_MAC_ID_RANGE_EN;
+	writeq(control, base + MLXBF_GIGE_CONTROL);
+
+	/* Set start of destination MAC range check to 0 */
+	writeq(0, base + MLXBF_GIGE_RX_MAC_FILTER_DMAC_RANGE_START);
+
+	/* Set end of destination MAC range check to all FFs */
+	writeq(0xFFFFFFFFFFFF, base + MLXBF_GIGE_RX_MAC_FILTER_DMAC_RANGE_END);
+}
+
+void mlxbf_gige_disable_promisc(struct mlxbf_gige *priv)
+{
+	void __iomem *base = priv->base;
+	u64 control;
+
+	/* Disable MAC_ID_RANGE match functionality */
+	control = readq(base + MLXBF_GIGE_CONTROL);
+	control &= ~MLXBF_GIGE_CONTROL_MAC_ID_RANGE_EN;
+	writeq(control, base + MLXBF_GIGE_CONTROL);
+
+	/* NOTE: no need to change DMAC_RANGE_START or END;
+	 * those values are ignored since MAC_ID_RANGE_EN=0
+	 */
+}
+
+/* Receive Initialization
+ * 1) Configures RX MAC filters via MMIO registers
+ * 2) Allocates RX WQE array using coherent DMA mapping
+ * 3) Initializes each element of RX WQE array with a receive
+ *    buffer pointer (also using coherent DMA mapping)
+ * 4) Allocates RX CQE array using coherent DMA mapping
+ * 5) Completes other misc receive initialization
+ */
+int mlxbf_gige_rx_init(struct mlxbf_gige *priv)
+{
+	size_t wq_size, cq_size;
+	dma_addr_t *rx_wqe_ptr;
+	dma_addr_t rx_buf_dma;
+	u64 data;
+	int i, j;
+
+	/* Configure MAC RX filter #0 to allow RX of broadcast pkts */
+	mlxbf_gige_set_mac_rx_filter(priv, MLXBF_GIGE_BCAST_MAC_FILTER_IDX,
+				     BCAST_MAC_ADDR);
+
+	wq_size = MLXBF_GIGE_RX_WQE_SZ * priv->rx_q_entries;
+	priv->rx_wqe_base = dma_alloc_coherent(priv->dev, wq_size,
+					       &priv->rx_wqe_base_dma,
+					       GFP_KERNEL);
+	if (!priv->rx_wqe_base)
+		return -ENOMEM;
+
+	/* Initialize 'rx_wqe_ptr' to point to first RX WQE in array
+	 * Each RX WQE is simply a receive buffer pointer, so walk
+	 * the entire array, allocating a 2KB buffer for each element
+	 */
+	rx_wqe_ptr = priv->rx_wqe_base;
+
+	for (i = 0; i < priv->rx_q_entries; i++) {
+		priv->rx_skb[i] = mlxbf_gige_alloc_skb(priv, MLXBF_GIGE_DEFAULT_BUF_SZ,
+						       &rx_buf_dma, DMA_FROM_DEVICE);
+		if (!priv->rx_skb[i])
+			goto free_wqe_and_skb;
+		*rx_wqe_ptr++ = rx_buf_dma;
+	}
+
+	/* Write RX WQE base address into MMIO reg */
+	writeq(priv->rx_wqe_base_dma, priv->base + MLXBF_GIGE_RX_WQ_BASE);
+
+	cq_size = MLXBF_GIGE_RX_CQE_SZ * priv->rx_q_entries;
+	priv->rx_cqe_base = dma_alloc_coherent(priv->dev, cq_size,
+					       &priv->rx_cqe_base_dma,
+					       GFP_KERNEL);
+	if (!priv->rx_cqe_base)
+		goto free_wqe_and_skb;
+
+	for (i = 0; i < priv->rx_q_entries; i++)
+		priv->rx_cqe_base[i] |= MLXBF_GIGE_RX_CQE_VALID_MASK;
+
+	/* Write RX CQE base address into MMIO reg */
+	writeq(priv->rx_cqe_base_dma, priv->base + MLXBF_GIGE_RX_CQ_BASE);
+
+	/* Write RX_WQE_PI with current number of replenished buffers */
+	writeq(priv->rx_q_entries, priv->base + MLXBF_GIGE_RX_WQE_PI);
+
+	/* Enable removal of CRC during RX */
+	data = readq(priv->base + MLXBF_GIGE_RX);
+	data |= MLXBF_GIGE_RX_STRIP_CRC_EN;
+	writeq(data, priv->base + MLXBF_GIGE_RX);
+
+	/* Enable RX MAC filter pass and discard counters */
+	writeq(MLXBF_GIGE_RX_MAC_FILTER_COUNT_DISC_EN,
+	       priv->base + MLXBF_GIGE_RX_MAC_FILTER_COUNT_DISC);
+	writeq(MLXBF_GIGE_RX_MAC_FILTER_COUNT_PASS_EN,
+	       priv->base + MLXBF_GIGE_RX_MAC_FILTER_COUNT_PASS);
+
+	/* Clear MLXBF_GIGE_INT_MASK 'receive pkt' bit to
+	 * indicate readiness to receive interrupts
+	 */
+	data = readq(priv->base + MLXBF_GIGE_INT_MASK);
+	data &= ~MLXBF_GIGE_INT_MASK_RX_RECEIVE_PACKET;
+	writeq(data, priv->base + MLXBF_GIGE_INT_MASK);
+
+	/* Enable RX DMA to write new packets to memory */
+	data = readq(priv->base + MLXBF_GIGE_RX_DMA);
+	data |= MLXBF_GIGE_RX_DMA_EN;
+	writeq(data, priv->base + MLXBF_GIGE_RX_DMA);
+
+	writeq(ilog2(priv->rx_q_entries),
+	       priv->base + MLXBF_GIGE_RX_WQE_SIZE_LOG2);
+
+	return 0;
+
+free_wqe_and_skb:
+	rx_wqe_ptr = priv->rx_wqe_base;
+	for (j = 0; j < i; j++) {
+		dma_unmap_single(priv->dev, *rx_wqe_ptr,
+				 MLXBF_GIGE_DEFAULT_BUF_SZ, DMA_FROM_DEVICE);
+		dev_kfree_skb(priv->rx_skb[j]);
+		rx_wqe_ptr++;
+	}
+	dma_free_coherent(priv->dev, wq_size,
+			  priv->rx_wqe_base, priv->rx_wqe_base_dma);
+	return -ENOMEM;
+}
+
+/* Receive Deinitialization
+ * This routine will free allocations done by mlxbf_gige_rx_init(),
+ * namely the RX WQE and RX CQE arrays, as well as all RX buffers
+ */
+void mlxbf_gige_rx_deinit(struct mlxbf_gige *priv)
+{
+	dma_addr_t *rx_wqe_ptr;
+	size_t size;
+	u64 data;
+	int i;
+
+	/* Disable RX DMA to prevent packet transfers to memory */
+	data = readq(priv->base + MLXBF_GIGE_RX_DMA);
+	data &= ~MLXBF_GIGE_RX_DMA_EN;
+	writeq(data, priv->base + MLXBF_GIGE_RX_DMA);
+
+	rx_wqe_ptr = priv->rx_wqe_base;
+
+	for (i = 0; i < priv->rx_q_entries; i++) {
+		dma_unmap_single(priv->dev, *rx_wqe_ptr, MLXBF_GIGE_DEFAULT_BUF_SZ,
+				 DMA_FROM_DEVICE);
+		dev_kfree_skb(priv->rx_skb[i]);
+		rx_wqe_ptr++;
+	}
+
+	size = MLXBF_GIGE_RX_WQE_SZ * priv->rx_q_entries;
+	dma_free_coherent(priv->dev, size,
+			  priv->rx_wqe_base, priv->rx_wqe_base_dma);
+
+	size = MLXBF_GIGE_RX_CQE_SZ * priv->rx_q_entries;
+	dma_free_coherent(priv->dev, size,
+			  priv->rx_cqe_base, priv->rx_cqe_base_dma);
+
+	priv->rx_wqe_base = NULL;
+	priv->rx_wqe_base_dma = 0;
+	priv->rx_cqe_base = NULL;
+	priv->rx_cqe_base_dma = 0;
+	writeq(0, priv->base + MLXBF_GIGE_RX_WQ_BASE);
+	writeq(0, priv->base + MLXBF_GIGE_RX_CQ_BASE);
+}
+
+static bool mlxbf_gige_rx_packet(struct mlxbf_gige *priv, int *rx_pkts)
+{
+	struct net_device *netdev = priv->netdev;
+	struct sk_buff *skb = NULL, *rx_skb;
+	u16 rx_pi_rem, rx_ci_rem;
+	dma_addr_t *rx_wqe_addr;
+	dma_addr_t rx_buf_dma;
+	u64 *rx_cqe_addr;
+	u64 datalen;
+	u64 rx_cqe;
+	u16 rx_ci;
+	u16 rx_pi;
+
+	/* Index into RX buffer array is rx_pi w/wrap based on RX_CQE_SIZE */
+	rx_pi = readq(priv->base + MLXBF_GIGE_RX_WQE_PI);
+	rx_pi_rem = rx_pi % priv->rx_q_entries;
+
+	rx_wqe_addr = priv->rx_wqe_base + rx_pi_rem;
+	rx_cqe_addr = priv->rx_cqe_base + rx_pi_rem;
+	rx_cqe = *rx_cqe_addr;
+
+	if ((!!(rx_cqe & MLXBF_GIGE_RX_CQE_VALID_MASK)) != priv->valid_polarity)
+		return false;
+
+	if ((rx_cqe & MLXBF_GIGE_RX_CQE_PKT_STATUS_MASK) == 0) {
+		/* Packet is OK, increment stats */
+		datalen = rx_cqe & MLXBF_GIGE_RX_CQE_PKT_LEN_MASK;
+		netdev->stats.rx_packets++;
+		netdev->stats.rx_bytes += datalen;
+
+		skb = priv->rx_skb[rx_pi_rem];
+
+		skb_put(skb, datalen);
+
+		skb->ip_summed = CHECKSUM_NONE; /* device did not checksum packet */
+
+		skb->protocol = eth_type_trans(skb, netdev);
+
+		/* Alloc another RX SKB for this same index */
+		rx_skb = mlxbf_gige_alloc_skb(priv, MLXBF_GIGE_DEFAULT_BUF_SZ,
+					      &rx_buf_dma, DMA_FROM_DEVICE);
+		if (!rx_skb)
+			return false;
+		priv->rx_skb[rx_pi_rem] = rx_skb;
+		dma_unmap_single(priv->dev, *rx_wqe_addr,
+				 MLXBF_GIGE_DEFAULT_BUF_SZ, DMA_FROM_DEVICE);
+		*rx_wqe_addr = rx_buf_dma;
+	} else if (rx_cqe & MLXBF_GIGE_RX_CQE_PKT_STATUS_MAC_ERR) {
+		priv->stats.rx_mac_errors++;
+	} else if (rx_cqe & MLXBF_GIGE_RX_CQE_PKT_STATUS_TRUNCATED) {
+		priv->stats.rx_truncate_errors++;
+	}
+
+	/* Let hardware know we've replenished one buffer */
+	rx_pi++;
+
+	/* Ensure completion of all writes before notifying HW of replenish */
+	wmb();
+	writeq(rx_pi, priv->base + MLXBF_GIGE_RX_WQE_PI);
+
+	(*rx_pkts)++;
+
+	rx_pi_rem = rx_pi % priv->rx_q_entries;
+	if (rx_pi_rem == 0)
+		priv->valid_polarity ^= 1;
+	rx_ci = readq(priv->base + MLXBF_GIGE_RX_CQE_PACKET_CI);
+	rx_ci_rem = rx_ci % priv->rx_q_entries;
+
+	if (skb)
+		netif_receive_skb(skb);
+
+	return rx_pi_rem != rx_ci_rem;
+}
+
+/* Driver poll() function called by NAPI infrastructure */
+int mlxbf_gige_poll(struct napi_struct *napi, int budget)
+{
+	struct mlxbf_gige *priv;
+	bool remaining_pkts;
+	int work_done = 0;
+	u64 data;
+
+	priv = container_of(napi, struct mlxbf_gige, napi);
+
+	mlxbf_gige_handle_tx_complete(priv);
+
+	do {
+		remaining_pkts = mlxbf_gige_rx_packet(priv, &work_done);
+	} while (remaining_pkts && work_done < budget);
+
+	/* If amount of work done < budget, turn off NAPI polling
+	 * via napi_complete_done(napi, work_done) and then
+	 * re-enable interrupts.
+	 */
+	if (work_done < budget && napi_complete_done(napi, work_done)) {
+		/* Clear MLXBF_GIGE_INT_MASK 'receive pkt' bit to
+		 * indicate receive readiness
+		 */
+		data = readq(priv->base + MLXBF_GIGE_INT_MASK);
+		data &= ~MLXBF_GIGE_INT_MASK_RX_RECEIVE_PACKET;
+		writeq(data, priv->base + MLXBF_GIGE_INT_MASK);
+	}
+
+	return work_done;
+}
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_tx.c b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_tx.c
new file mode 100644
index 000000000000..2683afc3854b
--- /dev/null
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_tx.c
@@ -0,0 +1,284 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+/* Packet transmit logic for Mellanox Gigabit Ethernet driver
+ *
+ * Copyright (C) 2020-2021 Mellanox Technologies, Ltd. ALL RIGHTS RESERVED.
+ */
+
+#include <linux/skbuff.h>
+
+#include "mlxbf_gige.h"
+#include "mlxbf_gige_regs.h"
+
+/* Transmit Initialization
+ * 1) Allocates TX WQE array using coherent DMA mapping
+ * 2) Allocates TX completion counter using coherent DMA mapping
+ */
+int mlxbf_gige_tx_init(struct mlxbf_gige *priv)
+{
+	size_t size;
+
+	size = MLXBF_GIGE_TX_WQE_SZ * priv->tx_q_entries;
+	priv->tx_wqe_base = dma_alloc_coherent(priv->dev, size,
+					       &priv->tx_wqe_base_dma,
+					       GFP_KERNEL);
+	if (!priv->tx_wqe_base)
+		return -ENOMEM;
+
+	priv->tx_wqe_next = priv->tx_wqe_base;
+
+	/* Write TX WQE base address into MMIO reg */
+	writeq(priv->tx_wqe_base_dma, priv->base + MLXBF_GIGE_TX_WQ_BASE);
+
+	/* Allocate address for TX completion count */
+	priv->tx_cc = dma_alloc_coherent(priv->dev, MLXBF_GIGE_TX_CC_SZ,
+					 &priv->tx_cc_dma, GFP_KERNEL);
+	if (!priv->tx_cc) {
+		dma_free_coherent(priv->dev, size,
+				  priv->tx_wqe_base, priv->tx_wqe_base_dma);
+		return -ENOMEM;
+	}
+
+	/* Write TX CC base address into MMIO reg */
+	writeq(priv->tx_cc_dma, priv->base + MLXBF_GIGE_TX_CI_UPDATE_ADDRESS);
+
+	writeq(ilog2(priv->tx_q_entries),
+	       priv->base + MLXBF_GIGE_TX_WQ_SIZE_LOG2);
+
+	priv->prev_tx_ci = 0;
+	priv->tx_pi = 0;
+
+	return 0;
+}
+
+/* Transmit Deinitialization
+ * This routine will free allocations done by mlxbf_gige_tx_init(),
+ * namely the TX WQE array and the TX completion counter
+ */
+void mlxbf_gige_tx_deinit(struct mlxbf_gige *priv)
+{
+	u64 *tx_wqe_addr;
+	size_t size;
+	int i;
+
+	tx_wqe_addr = priv->tx_wqe_base;
+
+	for (i = 0; i < priv->tx_q_entries; i++) {
+		if (priv->tx_skb[i]) {
+			dma_unmap_single(priv->dev, *tx_wqe_addr,
+					 priv->tx_skb[i]->len, DMA_TO_DEVICE);
+			dev_kfree_skb(priv->tx_skb[i]);
+			priv->tx_skb[i] = NULL;
+		}
+		tx_wqe_addr += 2;
+	}
+
+	size = MLXBF_GIGE_TX_WQE_SZ * priv->tx_q_entries;
+	dma_free_coherent(priv->dev, size,
+			  priv->tx_wqe_base, priv->tx_wqe_base_dma);
+
+	dma_free_coherent(priv->dev, MLXBF_GIGE_TX_CC_SZ,
+			  priv->tx_cc, priv->tx_cc_dma);
+
+	priv->tx_wqe_base = NULL;
+	priv->tx_wqe_base_dma = 0;
+	priv->tx_cc = NULL;
+	priv->tx_cc_dma = 0;
+	priv->tx_wqe_next = NULL;
+	writeq(0, priv->base + MLXBF_GIGE_TX_WQ_BASE);
+	writeq(0, priv->base + MLXBF_GIGE_TX_CI_UPDATE_ADDRESS);
+}
+
+/* Function that returns status of TX ring:
+ *          0: TX ring is full, i.e. there are no
+ *             available un-used entries in TX ring.
+ *   non-null: TX ring is not full, i.e. there are
+ *             some available entries in TX ring.
+ *             The non-null value is a measure of
+ *             how many TX entries are available, but
+ *             it is not the exact number of available
+ *             entries (see below).
+ *
+ * The algorithm makes the assumption that if
+ * (prev_tx_ci == tx_pi) then the TX ring is empty.
+ * An empty ring actually has (tx_q_entries-1)
+ * entries, which allows the algorithm to differentiate
+ * the case of an empty ring vs. a full ring.
+ */
+static u16 mlxbf_gige_tx_buffs_avail(struct mlxbf_gige *priv)
+{
+	unsigned long flags;
+	u16 avail;
+
+	spin_lock_irqsave(&priv->lock, flags);
+
+	if (priv->prev_tx_ci == priv->tx_pi)
+		avail = priv->tx_q_entries - 1;
+	else
+		avail = ((priv->tx_q_entries + priv->prev_tx_ci - priv->tx_pi)
+			  % priv->tx_q_entries) - 1;
+
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	return avail;
+}
+
+bool mlxbf_gige_handle_tx_complete(struct mlxbf_gige *priv)
+{
+	struct net_device_stats *stats;
+	u16 tx_wqe_index;
+	u64 *tx_wqe_addr;
+	u64 tx_status;
+	u16 tx_ci;
+
+	tx_status = readq(priv->base + MLXBF_GIGE_TX_STATUS);
+	if (tx_status & MLXBF_GIGE_TX_STATUS_DATA_FIFO_FULL)
+		priv->stats.tx_fifo_full++;
+	tx_ci = readq(priv->base + MLXBF_GIGE_TX_CONSUMER_INDEX);
+	stats = &priv->netdev->stats;
+
+	/* Transmit completion logic needs to loop until the completion
+	 * index (in SW) equals TX consumer index (from HW).  These
+	 * parameters are unsigned 16-bit values and the wrap case needs
+	 * to be supported, that is TX consumer index wrapped from 0xFFFF
+	 * to 0 while TX completion index is still < 0xFFFF.
+	 */
+	for (; priv->prev_tx_ci != tx_ci; priv->prev_tx_ci++) {
+		tx_wqe_index = priv->prev_tx_ci % priv->tx_q_entries;
+		/* Each TX WQE is 16 bytes. The 8 MSB store the 2KB TX
+		 * buffer address and the 8 LSB contain information
+		 * about the TX WQE.
+		 */
+		tx_wqe_addr = priv->tx_wqe_base +
+			       (tx_wqe_index * MLXBF_GIGE_TX_WQE_SZ_QWORDS);
+
+		stats->tx_packets++;
+		stats->tx_bytes += MLXBF_GIGE_TX_WQE_PKT_LEN(tx_wqe_addr);
+
+		dma_unmap_single(priv->dev, *tx_wqe_addr,
+				 priv->tx_skb[tx_wqe_index]->len, DMA_TO_DEVICE);
+		dev_consume_skb_any(priv->tx_skb[tx_wqe_index]);
+		priv->tx_skb[tx_wqe_index] = NULL;
+
+		/* Ensure completion of updates across all cores */
+		mb();
+	}
+
+	/* Since the TX ring was likely just drained, check if TX queue
+	 * had previously been stopped and now that there are TX buffers
+	 * available the TX queue can be awakened.
+	 */
+	if (netif_queue_stopped(priv->netdev) &&
+	    mlxbf_gige_tx_buffs_avail(priv))
+		netif_wake_queue(priv->netdev);
+
+	return true;
+}
+
+/* Function to advance the tx_wqe_next pointer to next TX WQE */
+void mlxbf_gige_update_tx_wqe_next(struct mlxbf_gige *priv)
+{
+	/* Advance tx_wqe_next pointer */
+	priv->tx_wqe_next += MLXBF_GIGE_TX_WQE_SZ_QWORDS;
+
+	/* Check if 'next' pointer is beyond end of TX ring */
+	/* If so, set 'next' back to 'base' pointer of ring */
+	if (priv->tx_wqe_next == (priv->tx_wqe_base +
+				  (priv->tx_q_entries * MLXBF_GIGE_TX_WQE_SZ_QWORDS)))
+		priv->tx_wqe_next = priv->tx_wqe_base;
+}
+
+netdev_tx_t mlxbf_gige_start_xmit(struct sk_buff *skb,
+				  struct net_device *netdev)
+{
+	struct mlxbf_gige *priv = netdev_priv(netdev);
+	long buff_addr, start_dma_page, end_dma_page;
+	struct sk_buff *tx_skb;
+	dma_addr_t tx_buf_dma;
+	unsigned long flags;
+	u64 *tx_wqe_addr;
+	u64 word2;
+
+	/* If needed, linearize TX SKB as hardware DMA expects this */
+	if (skb->len > MLXBF_GIGE_DEFAULT_BUF_SZ || skb_linearize(skb)) {
+		dev_kfree_skb(skb);
+		netdev->stats.tx_dropped++;
+		return NETDEV_TX_OK;
+	}
+
+	buff_addr = (long)skb->data;
+	start_dma_page = buff_addr >> MLXBF_GIGE_DMA_PAGE_SHIFT;
+	end_dma_page   = (buff_addr + skb->len - 1) >> MLXBF_GIGE_DMA_PAGE_SHIFT;
+
+	/* Verify that payload pointer and data length of SKB to be
+	 * transmitted does not violate the hardware DMA limitation.
+	 */
+	if (start_dma_page != end_dma_page) {
+		/* DMA operation would fail as-is, alloc new aligned SKB */
+		tx_skb = mlxbf_gige_alloc_skb(priv, skb->len,
+					      &tx_buf_dma, DMA_TO_DEVICE);
+		if (!tx_skb) {
+			/* Free original skb, could not alloc new aligned SKB */
+			dev_kfree_skb(skb);
+			netdev->stats.tx_dropped++;
+			return NETDEV_TX_OK;
+		}
+
+		skb_put_data(tx_skb, skb->data, skb->len);
+
+		/* Free the original SKB */
+		dev_kfree_skb(skb);
+	} else {
+		tx_skb = skb;
+		tx_buf_dma = dma_map_single(priv->dev, skb->data,
+					    skb->len, DMA_TO_DEVICE);
+		if (dma_mapping_error(priv->dev, tx_buf_dma)) {
+			dev_kfree_skb(skb);
+			netdev->stats.tx_dropped++;
+			return NETDEV_TX_OK;
+		}
+	}
+
+	/* Get address of TX WQE */
+	tx_wqe_addr = priv->tx_wqe_next;
+
+	mlxbf_gige_update_tx_wqe_next(priv);
+
+	/* Put PA of buffer address into first 64-bit word of TX WQE */
+	*tx_wqe_addr = tx_buf_dma;
+
+	/* Set TX WQE pkt_len appropriately
+	 * NOTE: GigE silicon will automatically pad up to
+	 *       minimum packet length if needed.
+	 */
+	word2 = tx_skb->len & MLXBF_GIGE_TX_WQE_PKT_LEN_MASK;
+
+	/* Write entire 2nd word of TX WQE */
+	*(tx_wqe_addr + 1) = word2;
+
+	spin_lock_irqsave(&priv->lock, flags);
+	priv->tx_skb[priv->tx_pi % priv->tx_q_entries] = tx_skb;
+	priv->tx_pi++;
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	if (!netdev_xmit_more()) {
+		/* Create memory barrier before write to TX PI */
+		wmb();
+		writeq(priv->tx_pi, priv->base + MLXBF_GIGE_TX_PRODUCER_INDEX);
+	}
+
+	/* Check if the last TX entry was just used */
+	if (!mlxbf_gige_tx_buffs_avail(priv)) {
+		/* TX ring is full, inform stack */
+		netif_stop_queue(netdev);
+
+		/* Since there is no separate "TX complete" interrupt, need
+		 * to explicitly schedule NAPI poll.  This will trigger logic
+		 * which processes TX completions, and will hopefully drain
+		 * the TX ring allowing the TX queue to be awakened.
+		 */
+		napi_schedule(&priv->napi);
+	}
+
+	return NETDEV_TX_OK;
+}
