@@ -93,6 +93,12 @@ static inline void set_float_infzeronan_rule(FloatInfZeroNaNRule rule,
status->float_infzeronan_rule = rule;
}
+static inline void set_float_default_nan_pattern(uint8_t dnan_pattern,
+ float_status *status)
+{
+ status->default_nan_pattern = dnan_pattern;
+}
+
static inline void set_flush_to_zero(bool val, float_status *status)
{
status->flush_to_zero = val;
@@ -154,6 +160,11 @@ static inline FloatInfZeroNaNRule get_float_infzeronan_rule(float_status *status
return status->float_infzeronan_rule;
}
+static inline uint8_t get_float_default_nan_pattern(float_status *status)
+{
+ return status->default_nan_pattern;
+}
+
static inline bool get_flush_to_zero(float_status *status)
{
return status->flush_to_zero;
@@ -303,6 +303,16 @@ typedef struct float_status {
/* should denormalised inputs go to zero and set the input_denormal flag? */
bool flush_inputs_to_zero;
bool default_nan_mode;
+ /*
+ * The pattern to use for the default NaN. Here the high bit specifies
+ * the default NaN's sign bit, and bits 6..0 specify the high bits of the
+ * fractional part. The low bits of the fractional part are copies of bit 0.
+ * The exponent of the default NaN is (as for any NaN) always all 1s.
+ * Note that a value of 0 here is not a valid NaN. The target must set
+ * this to the correct non-zero value, or we will assert when trying to
+ * create a default NaN.
+ */
+ uint8_t default_nan_pattern;
/*
* The flags below are not used on all specializations and may
* constant fold away (see snan_bit_is_one()/no_signalling_nans() in
@@ -133,35 +133,46 @@ static void parts64_default_nan(FloatParts64 *p, float_status *status)
{
bool sign = 0;
uint64_t frac;
+ uint8_t dnan_pattern = status->default_nan_pattern;
+ if (dnan_pattern == 0) {
#if defined(TARGET_SPARC) || defined(TARGET_M68K)
- /* !snan_bit_is_one, set all bits */
- frac = (1ULL << DECOMPOSED_BINARY_POINT) - 1;
-#elif defined(TARGET_I386) || defined(TARGET_X86_64) \
+ /* Sign bit clear, all frac bits set */
+ dnan_pattern = 0b01111111;
+#elif defined(TARGET_I386) || defined(TARGET_X86_64) \
|| defined(TARGET_MICROBLAZE)
- /* !snan_bit_is_one, set sign and msb */
- frac = 1ULL << (DECOMPOSED_BINARY_POINT - 1);
- sign = 1;
+ /* Sign bit set, most significant frac bit set */
+ dnan_pattern = 0b11000000;
#elif defined(TARGET_HPPA)
- /* snan_bit_is_one, set msb-1. */
- frac = 1ULL << (DECOMPOSED_BINARY_POINT - 2);
+ /* Sign bit clear, msb-1 frac bit set */
+ dnan_pattern = 0b00100000;
#elif defined(TARGET_HEXAGON)
- sign = 1;
- frac = ~0ULL;
+ /* Sign bit set, all frac bits set. */
+ dnan_pattern = 0b11111111;
#else
- /*
- * This case is true for Alpha, ARM, MIPS, OpenRISC, PPC, RISC-V,
- * S390, SH4, TriCore, and Xtensa. Our other supported targets
- * do not have floating-point.
- */
- if (snan_bit_is_one(status)) {
- /* set all bits other than msb */
- frac = (1ULL << (DECOMPOSED_BINARY_POINT - 1)) - 1;
- } else {
- /* set msb */
- frac = 1ULL << (DECOMPOSED_BINARY_POINT - 1);
- }
+ /*
+ * This case is true for Alpha, ARM, MIPS, OpenRISC, PPC, RISC-V,
+ * S390, SH4, TriCore, and Xtensa. Our other supported targets
+ * do not have floating-point.
+ */
+ if (snan_bit_is_one(status)) {
+ /* sign bit clear, set all frac bits other than msb */
+ dnan_pattern = 0b00111111;
+ } else {
+ /* sign bit clear, set frac msb */
+ dnan_pattern = 0b01000000;
+ }
#endif
+ }
+ assert(dnan_pattern != 0);
+
+ sign = dnan_pattern >> 7;
+ /*
+ * Place default_nan_pattern [6:0] into bits [62:56],
+ * and replecate bit [0] down into [55:0]
+ */
+ frac = deposit64(0, DECOMPOSED_BINARY_POINT - 7, 7, dnan_pattern);
+ frac = deposit64(frac, 0, DECOMPOSED_BINARY_POINT - 7, -(dnan_pattern & 1));
*p = (FloatParts64) {
.cls = float_class_qnan,
Currently we hardcode the default NaN value in parts64_default_nan() using a compile-time ifdef ladder. This is awkward for two cases: * for single-QEMU-binary we can't hard-code target-specifics like this * for Arm FEAT_AFP the default NaN value depends on FPCR.AH (specifically the sign bit is different) Add a field to float_status to specify the default NaN value; fall back to the old ifdef behaviour if these are not set. The default NaN value is specified by setting a uint8_t to a pattern corresponding to the sign and upper fraction parts of the NaN; the lower bits of the fraction are set from bit 0 of the pattern. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/fpu/softfloat-helpers.h | 11 +++++++ include/fpu/softfloat-types.h | 10 ++++++ fpu/softfloat-specialize.c.inc | 55 ++++++++++++++++++++------------- 3 files changed, 54 insertions(+), 22 deletions(-)