diff mbox series

[5.4,66/70] serial: 8250_pci: rewrite pericom_do_set_divisor()

Message ID 20211206145554.212061966@linuxfoundation.org
State New
Headers show
Series None | expand

Commit Message

Greg Kroah-Hartman Dec. 6, 2021, 2:57 p.m. UTC 
From: Jay Dolan <jay.dolan@accesio.com>

commit bb1201d4b38ec67bd9a871cf86b0cc10f28b15b5 upstream.

Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.

Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.

Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.

Fixes: 6bf4e42f1d19 ("serial: 8250: Add support for higher baud rates to Pericom chips")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/tty/serial/8250/8250_pci.c |   30 +++++++++++++++++-------------
 1 file changed, 17 insertions(+), 13 deletions(-)
diff mbox series

Patch

--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1351,29 +1351,33 @@  pericom_do_set_divisor(struct uart_port
 {
 	int scr;
 	int lcr;
-	int actual_baud;
-	int tolerance;
 
-	for (scr = 5 ; scr <= 15 ; scr++) {
-		actual_baud = 921600 * 16 / scr;
-		tolerance = actual_baud / 50;
+	for (scr = 16; scr > 4; scr--) {
+		unsigned int maxrate = port->uartclk / scr;
+		unsigned int divisor = max(maxrate / baud, 1U);
+		int delta = maxrate / divisor - baud;
 
-		if ((baud < actual_baud + tolerance) &&
-			(baud > actual_baud - tolerance)) {
+		if (baud > maxrate + baud / 50)
+			continue;
 
+		if (delta > baud / 50)
+			divisor++;
+
+		if (divisor > 0xffff)
+			continue;
+
+		/* Update delta due to possible divisor change */
+		delta = maxrate / divisor - baud;
+		if (abs(delta) < baud / 50) {
 			lcr = serial_port_in(port, UART_LCR);
 			serial_port_out(port, UART_LCR, lcr | 0x80);
-
-			serial_port_out(port, UART_DLL, 1);
-			serial_port_out(port, UART_DLM, 0);
+			serial_port_out(port, UART_DLL, divisor & 0xff);
+			serial_port_out(port, UART_DLM, divisor >> 8 & 0xff);
 			serial_port_out(port, 2, 16 - scr);
 			serial_port_out(port, UART_LCR, lcr);
 			return;
-		} else if (baud > actual_baud) {
-			break;
 		}
 	}
-	serial8250_do_set_divisor(port, baud, quot, quot_frac);
 }
 static int pci_pericom_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,