diff mbox series

[5.16,0114/1039] wcn36xx: populate band before determining rate on RX

Message ID 20220124184128.961150656@linuxfoundation.org
State Superseded
Headers show
Series None | expand

Commit Message

Greg Kroah-Hartman Jan. 24, 2022, 6:31 p.m. UTC 
From: Benjamin Li <benl@squareup.com>

[ Upstream commit c9c5608fafe4dae975c9644c7d14c51ad3b0ed73 ]

status.band is used in determination of status.rate -- for 5GHz on legacy
rates there is a linear shift between the BD descriptor's rate field and
the wcn36xx driver's rate table (wcn_5ghz_rates).

We have a special clause to populate status.band for hardware scan offload
frames. However, this block occurs after status.rate is already populated.
Correctly handle this dependency by moving the band block before the rate
block.

This patch addresses kernel warnings & missing scan results for 5GHz APs
that send their beacons/probe responses at the higher four legacy rates
(24-54 Mbps), when using hardware scan offload:

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4532 ieee80211_rx_napi+0x744/0x8d8
  Modules linked in: wcn36xx [...]
  CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W         4.19.107-g73909fa #1
  Hardware name: Square, Inc. T2 (all variants) (DT)
  Call trace:
  dump_backtrace+0x0/0x148
  show_stack+0x14/0x1c
  dump_stack+0xb8/0xf0
  __warn+0x2ac/0x2d8
  warn_slowpath_null+0x44/0x54
  ieee80211_rx_napi+0x744/0x8d8
  ieee80211_tasklet_handler+0xa4/0xe0
  tasklet_action_common+0xe0/0x118
  tasklet_action+0x20/0x28
  __do_softirq+0x108/0x1ec
  irq_exit+0xd4/0xd8
  __handle_domain_irq+0x84/0xbc
  gic_handle_irq+0x4c/0xb8
  el1_irq+0xe8/0x190
  lpm_cpuidle_enter+0x220/0x260
  cpuidle_enter_state+0x114/0x1c0
  cpuidle_enter+0x34/0x48
  do_idle+0x150/0x268
  cpu_startup_entry+0x20/0x24
  rest_init+0xd4/0xe0
  start_kernel+0x398/0x430
  ---[ end trace ae28cb759352b403 ]---

Fixes: 8a27ca394782 ("wcn36xx: Correct band/freq reporting on RX")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104010548.1107405-2-benl@squareup.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/wcn36xx/txrx.c | 37 +++++++++++++------------
 1 file changed, 19 insertions(+), 18 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/wireless/ath/wcn36xx/txrx.c b/drivers/net/wireless/ath/wcn36xx/txrx.c
index 75951ccbc840e..f0a9f069a92a9 100644
--- a/drivers/net/wireless/ath/wcn36xx/txrx.c
+++ b/drivers/net/wireless/ath/wcn36xx/txrx.c
@@ -314,8 +314,6 @@  int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
 	fc = __le16_to_cpu(hdr->frame_control);
 	sn = IEEE80211_SEQ_TO_SN(__le16_to_cpu(hdr->seq_ctrl));
 
-	status.freq = WCN36XX_CENTER_FREQ(wcn);
-	status.band = WCN36XX_BAND(wcn);
 	status.mactime = 10;
 	status.signal = -get_rssi0(bd);
 	status.antenna = 1;
@@ -327,6 +325,25 @@  int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
 
 	wcn36xx_dbg(WCN36XX_DBG_RX, "status.flags=%x\n", status.flag);
 
+	if (bd->scan_learn) {
+		/* If packet originate from hardware scanning, extract the
+		 * band/channel from bd descriptor.
+		 */
+		u8 hwch = (bd->reserved0 << 4) + bd->rx_ch;
+
+		if (bd->rf_band != 1 && hwch <= sizeof(ab_rx_ch_map) && hwch >= 1) {
+			status.band = NL80211_BAND_5GHZ;
+			status.freq = ieee80211_channel_to_frequency(ab_rx_ch_map[hwch - 1],
+								     status.band);
+		} else {
+			status.band = NL80211_BAND_2GHZ;
+			status.freq = ieee80211_channel_to_frequency(hwch, status.band);
+		}
+	} else {
+		status.band = WCN36XX_BAND(wcn);
+		status.freq = WCN36XX_CENTER_FREQ(wcn);
+	}
+
 	if (bd->rate_id < ARRAY_SIZE(wcn36xx_rate_table)) {
 		rate = &wcn36xx_rate_table[bd->rate_id];
 		status.encoding = rate->encoding;
@@ -353,22 +370,6 @@  int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
 	    ieee80211_is_probe_resp(hdr->frame_control))
 		status.boottime_ns = ktime_get_boottime_ns();
 
-	if (bd->scan_learn) {
-		/* If packet originates from hardware scanning, extract the
-		 * band/channel from bd descriptor.
-		 */
-		u8 hwch = (bd->reserved0 << 4) + bd->rx_ch;
-
-		if (bd->rf_band != 1 && hwch <= sizeof(ab_rx_ch_map) && hwch >= 1) {
-			status.band = NL80211_BAND_5GHZ;
-			status.freq = ieee80211_channel_to_frequency(ab_rx_ch_map[hwch - 1],
-								     status.band);
-		} else {
-			status.band = NL80211_BAND_2GHZ;
-			status.freq = ieee80211_channel_to_frequency(hwch, status.band);
-		}
-	}
-
 	memcpy(IEEE80211_SKB_RXCB(skb), &status, sizeof(status));
 
 	if (ieee80211_is_beacon(hdr->frame_control)) {