From patchwork Sat May 23 16:38:20 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Marek Vasut X-Patchwork-Id: 246358 List-Id: U-Boot discussion From: marek.vasut at gmail.com (Marek Vasut) Date: Sat, 23 May 2020 18:38:20 +0200 Subject: [PATCH 13/30] net: eepro100: Factor out tx_ring command issuing In-Reply-To: <20200523163837.407592-1-marek.vasut+renesas@gmail.com> References: <20200523163837.407592-1-marek.vasut+renesas@gmail.com> Message-ID: <20200523163837.407592-13-marek.vasut+renesas@gmail.com> This code is replicated in the driver thrice almost verbatim, factor it out into a separate function and clean it up. No functional change. Signed-off-by: Marek Vasut Reviewed-By: Ramon Fried --- drivers/net/eepro100.c | 124 ++++++++++++++++++----------------------- 1 file changed, 53 insertions(+), 71 deletions(-) diff --git a/drivers/net/eepro100.c b/drivers/net/eepro100.c index 6fb9192e81..03ba9a41a5 100644 --- a/drivers/net/eepro100.c +++ b/drivers/net/eepro100.c @@ -453,11 +453,44 @@ int eepro100_initialize(bd_t *bis) return card_number; } +static int eepro100_txcmd_send(struct eth_device *dev, + struct eepro100_txfd *desc) +{ + u16 rstat; + int i = 0; + + if (!wait_for_eepro100(dev)) + return -ETIMEDOUT; + + OUTL(dev, phys_to_bus((u32)desc), SCB_POINTER); + OUTW(dev, SCB_M | CU_START, SCB_CMD); + + while (true) { + rstat = le16_to_cpu(desc->status); + if (rstat & CONFIG_SYS_STATUS_C) + break; + + if (i++ >= TOUT_LOOP) { + printf("%s: Tx error buffer not ready\n", dev->name); + return -EINVAL; + } + } + + rstat = le16_to_cpu(desc->status); + + if (!(rstat & CONFIG_SYS_STATUS_OK)) { + printf("TX error status = 0x%08X\n", rstat); + return -EIO; + } + + return 0; +} + static int eepro100_init(struct eth_device *dev, bd_t *bis) { - int i, status = -1; + struct eepro100_txfd *ias_cmd, *cfg_cmd; + int ret, status = -1; int tx_cur; - struct descriptor *ias_cmd, *cfg_cmd; /* Reset the ethernet controller */ OUTL(dev, I82559_SELECTIVE_RESET, SCB_PORT); @@ -497,35 +530,19 @@ static int eepro100_init(struct eth_device *dev, bd_t *bis) tx_cur = tx_next; tx_next = ((tx_next + 1) % NUM_TX_DESC); - cfg_cmd = (struct descriptor *)&tx_ring[tx_cur]; + cfg_cmd = &tx_ring[tx_cur]; cfg_cmd->command = cpu_to_le16(CONFIG_SYS_CMD_SUSPEND | CONFIG_SYS_CMD_CONFIGURE); cfg_cmd->status = 0; cfg_cmd->link = cpu_to_le32(phys_to_bus((u32)&tx_ring[tx_next])); - memcpy(cfg_cmd->params, i82558_config_cmd, + memcpy(((struct descriptor *)cfg_cmd)->params, i82558_config_cmd, sizeof(i82558_config_cmd)); - if (!wait_for_eepro100(dev)) { - printf("Error---CONFIG_SYS_CMD_CONFIGURE: Can not reset ethernet controller.\n"); - goto done; - } - - OUTL(dev, phys_to_bus((u32)&tx_ring[tx_cur]), SCB_POINTER); - OUTW(dev, SCB_M | CU_START, SCB_CMD); - - for (i = 0; - !(le16_to_cpu(tx_ring[tx_cur].status) & CONFIG_SYS_STATUS_C); - i++) { - if (i >= TOUT_LOOP) { - printf("%s: Tx error buffer not ready\n", dev->name); - goto done; - } - } - - if (!(le16_to_cpu(tx_ring[tx_cur].status) & CONFIG_SYS_STATUS_OK)) { - printf("TX error status = 0x%08X\n", - le16_to_cpu(tx_ring[tx_cur].status)); + ret = eepro100_txcmd_send(dev, cfg_cmd); + if (ret) { + if (ret == -ETIMEDOUT) + printf("Error---CONFIG_SYS_CMD_CONFIGURE: Can not reset ethernet controller.\n"); goto done; } @@ -533,36 +550,18 @@ static int eepro100_init(struct eth_device *dev, bd_t *bis) tx_cur = tx_next; tx_next = ((tx_next + 1) % NUM_TX_DESC); - ias_cmd = (struct descriptor *)&tx_ring[tx_cur]; + ias_cmd = &tx_ring[tx_cur]; ias_cmd->command = cpu_to_le16(CONFIG_SYS_CMD_SUSPEND | CONFIG_SYS_CMD_IAS); ias_cmd->status = 0; ias_cmd->link = cpu_to_le32(phys_to_bus((u32)&tx_ring[tx_next])); - memcpy(ias_cmd->params, dev->enetaddr, 6); - - /* Tell the adapter where the TX ring is located. */ - if (!wait_for_eepro100(dev)) { - printf("Error: Can not reset ethernet controller.\n"); - goto done; - } - - OUTL(dev, phys_to_bus((u32)&tx_ring[tx_cur]), SCB_POINTER); - OUTW(dev, SCB_M | CU_START, SCB_CMD); - - for (i = 0; - !(le16_to_cpu(tx_ring[tx_cur].status) & CONFIG_SYS_STATUS_C); - i++) { - if (i >= TOUT_LOOP) { - printf("%s: Tx error buffer not ready\n", - dev->name); - goto done; - } - } + memcpy(((struct descriptor *)ias_cmd)->params, dev->enetaddr, 6); - if (!(le16_to_cpu(tx_ring[tx_cur].status) & CONFIG_SYS_STATUS_OK)) { - printf("TX error status = 0x%08X\n", - le16_to_cpu(tx_ring[tx_cur].status)); + ret = eepro100_txcmd_send(dev, ias_cmd); + if (ret) { + if (ret == -ETIMEDOUT) + printf("Error: Can not reset ethernet controller.\n"); goto done; } @@ -574,7 +573,7 @@ done: static int eepro100_send(struct eth_device *dev, void *packet, int length) { - int i, status = -1; + int ret, status = -1; int tx_cur; if (length <= 0) { @@ -597,28 +596,11 @@ static int eepro100_send(struct eth_device *dev, void *packet, int length) cpu_to_le32 (phys_to_bus((u_long)packet)); tx_ring[tx_cur].tx_buf_size0 = cpu_to_le32 (length); - if (!wait_for_eepro100(dev)) { - printf("%s: Tx error ethernet controller not ready.\n", - dev->name); - goto done; - } - - /* Send the packet. */ - OUTL(dev, phys_to_bus((u32)&tx_ring[tx_cur]), SCB_POINTER); - OUTW(dev, SCB_M | CU_START, SCB_CMD); - - for (i = 0; - !(le16_to_cpu(tx_ring[tx_cur].status) & CONFIG_SYS_STATUS_C); - i++) { - if (i >= TOUT_LOOP) { - printf("%s: Tx error buffer not ready\n", dev->name); - goto done; - } - } - - if (!(le16_to_cpu(tx_ring[tx_cur].status) & CONFIG_SYS_STATUS_OK)) { - printf("TX error status = 0x%08X\n", - le16_to_cpu(tx_ring[tx_cur].status)); + ret = eepro100_txcmd_send(dev, &tx_ring[tx_cur]); + if (ret) { + if (ret == -ETIMEDOUT) + printf("%s: Tx error ethernet controller not ready.\n", + dev->name); goto done; }