@@ -212,14 +212,6 @@ dtb-$(CONFIG_ARCH_MESON) += \
meson-a1-ad401.dtb \
meson-axg-s400.dtb \
meson-axg-jethome-jethub-j100.dtb \
- meson-gxbb-kii-pro.dtb \
- meson-gxbb-nanopi-k2.dtb \
- meson-gxbb-odroidc2.dtb \
- meson-gxbb-nanopi-k2.dtb \
- meson-gxbb-p200.dtb \
- meson-gxbb-p201.dtb \
- meson-gxbb-wetek-hub.dtb \
- meson-gxbb-wetek-play2.dtb \
meson-gxl-s805x-libretech-ac.dtb \
meson-gxl-s905d-libretech-pc.dtb \
meson-gxl-s905w-jethome-jethub-j80.dtb \
deleted file mode 100644
@@ -1,140 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2019 Mohammad Rasim <mohammad.rasim96@gmail.com>
- */
-
-/dts-v1/;
-
-#include "meson-gxbb-p20x.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/sound/meson-aiu.h>
-
-/ {
- compatible = "videostrong,kii-pro", "amlogic,meson-gxbb";
- model = "Videostrong KII Pro";
-
- spdif_dit: audio-codec-0 {
- #sound-dai-cells = <0>;
- compatible = "linux,spdif-dit";
- status = "okay";
- sound-name-prefix = "DIT";
- };
-
- leds {
- compatible = "gpio-leds";
- led {
- gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
- color = <LED_COLOR_ID_RED>;
- function = LED_FUNCTION_STATUS;
- default-state = "off";
- };
- };
-
- gpio-keys-polled {
- compatible = "gpio-keys-polled";
- poll-interval = <20>;
-
- button-reset {
- label = "reset";
- linux,code = <KEY_POWER>;
- gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
- };
- };
-
- sound {
- compatible = "amlogic,gx-sound-card";
- model = "KII-PRO";
- assigned-clocks = <&clkc CLKID_MPLL0>,
- <&clkc CLKID_MPLL1>,
- <&clkc CLKID_MPLL2>;
- assigned-clock-parents = <0>, <0>, <0>;
- assigned-clock-rates = <294912000>,
- <270950400>,
- <393216000>;
-
- dai-link-0 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
- };
-
- dai-link-1 {
- sound-dai = <&aiu AIU_CPU CPU_SPDIF_FIFO>;
- };
-
- dai-link-2 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
- dai-format = "i2s";
- mclk-fs = <256>;
-
- codec-0 {
- sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
- };
- };
-
- dai-link-3 {
- sound-dai = <&aiu AIU_CPU CPU_SPDIF_ENCODER>;
-
- codec-0 {
- sound-dai = <&spdif_dit>;
- };
- };
-
- dai-link-4 {
- sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
-
- codec-0 {
- sound-dai = <&hdmi_tx>;
- };
- };
- };
-};
-
-&aiu {
- status = "okay";
- pinctrl-0 = <&spdif_out_y_pins>;
- pinctrl-names = "default";
-};
-
-ðmac {
- status = "okay";
- pinctrl-0 = <ð_rmii_pins>;
- pinctrl-names = "default";
-
- phy-handle = <ð_phy0>;
- phy-mode = "rmii";
-
- mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- eth_phy0: ethernet-phy@0 {
- /* IC Plus IP101GR (0x02430c54) */
- reg = <0>;
- reset-assert-us = <10000>;
- reset-deassert-us = <10000>;
- reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-&ir {
- linux,rc-map-name = "rc-videostrong-kii-pro";
-};
-
-&uart_A {
- status = "okay";
- pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
- pinctrl-names = "default";
- uart-has-rtscts;
-
- bluetooth {
- compatible = "brcm,bcm4335a0";
- shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
- host-wakeup-gpios = <&gpio GPIOX_21 GPIO_ACTIVE_HIGH>;
- max-speed = <2000000>;
- clocks = <&wifi32k>;
- clock-names = "lpo";
- };
-};
deleted file mode 100644
@@ -1,415 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2017 Andreas Färber
- */
-
-/dts-v1/;
-
-#include "meson-gxbb.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/sound/meson-aiu.h>
-
-/ {
- compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
- model = "FriendlyARM NanoPi K2";
-
- aliases {
- serial0 = &uart_AO;
- ethernet0 = ðmac;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0 0x80000000>;
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-stat {
- label = "nanopi-k2:blue:stat";
- gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- panic-indicator;
- };
- };
-
- vdd_5v: regulator-vdd-5v {
- compatible = "regulator-fixed";
- regulator-name = "VDD_5V";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- vddio_ao18: regulator-vddio-ao18 {
- compatible = "regulator-fixed";
- regulator-name = "VDDIO_AO18";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vddio_ao3v3: regulator-vddio-ao3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VDDIO_AO3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vddio_tf: regulator-vddio-tf {
- compatible = "regulator-gpio";
-
- regulator-name = "VDDIO_TF";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
-
- states = <3300000 0>,
- <1800000 1>;
-
- regulator-settling-time-up-us = <100>;
- regulator-settling-time-down-us = <5000>;
- };
-
- wifi_32k: wifi-32k {
- compatible = "pwm-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
- };
-
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
- clocks = <&wifi_32k>;
- clock-names = "ext_clock";
- };
-
- vcc1v8: regulator-vcc1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VCC1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vcc3v3: regulator-vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- emmc_pwrseq: emmc-pwrseq {
- compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
- };
-
- /* CVBS is available on CON1 pin 36, disabled by default */
- cvbs-connector {
- compatible = "composite-video-connector";
- status = "disabled";
-
- port {
- cvbs_connector_in: endpoint {
- remote-endpoint = <&cvbs_vdac_out>;
- };
- };
- };
-
- hdmi-connector {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&hdmi_tx_tmds_out>;
- };
- };
- };
-
- sound {
- compatible = "amlogic,gx-sound-card";
- model = "NANOPI-K2";
- assigned-clocks = <&clkc CLKID_MPLL0>,
- <&clkc CLKID_MPLL1>,
- <&clkc CLKID_MPLL2>;
- assigned-clock-parents = <0>, <0>, <0>;
- assigned-clock-rates = <294912000>,
- <270950400>,
- <393216000>;
- status = "okay";
-
- dai-link-0 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
- };
-
- dai-link-1 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
- dai-format = "i2s";
- mclk-fs = <256>;
-
- codec-0 {
- sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
- };
- };
-
- dai-link-2 {
- sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
-
- codec-0 {
- sound-dai = <&hdmi_tx>;
- };
- };
- };
-};
-
-&aiu {
- status = "okay";
-};
-
-&cec_AO {
- status = "okay";
- pinctrl-0 = <&ao_cec_pins>;
- pinctrl-names = "default";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-&cvbs_vdac_port {
- cvbs_vdac_out: endpoint {
- remote-endpoint = <&cvbs_connector_in>;
- };
-};
-
-ðmac {
- status = "okay";
- pinctrl-0 = <ð_rgmii_pins>;
- pinctrl-names = "default";
-
- phy-handle = <ð_phy0>;
- phy-mode = "rgmii";
-
- amlogic,tx-delay-ns = <2>;
-
- mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- eth_phy0: ethernet-phy@0 {
- /* Realtek RTL8211F (0x001cc916) */
- reg = <0>;
-
- reset-assert-us = <10000>;
- reset-deassert-us = <80000>;
- reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
-
- interrupt-parent = <&gpio_intc>;
- /* MAC_INTR on GPIOZ_15 */
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
- };
- };
-};
-
-&hdmi_tx {
- status = "okay";
- pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
- pinctrl-names = "default";
-};
-
-&hdmi_tx_tmds_port {
- hdmi_tx_tmds_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
-};
-
-&ir {
- status = "okay";
- pinctrl-0 = <&remote_input_ao_pins>;
- pinctrl-names = "default";
-};
-
-&gpio_ao {
- gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
- "VCCK En", "CON1 Header Pin31",
- "I2S Header Pin6", "IR In", "I2S Header Pin7",
- "I2S Header Pin3", "I2S Header Pin4",
- "I2S Header Pin5", "HDMI CEC", "SYS LED",
- /* GPIO_TEST_N */
- "";
-};
-
-&gpio {
- gpio-line-names = /* Bank GPIOZ */
- "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
- "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
- "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
- "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
- "Eth PHY nRESET", "Eth PHY Intc",
- /* Bank GPIOH */
- "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
- "CON1 Header Pin33",
- /* Bank BOOT */
- "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
- "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
- "eMMC Reset", "eMMC CMD",
- "", "", "", "", "eMMC DS",
- "", "",
- /* Bank CARD */
- "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
- "SDCard D3", "SDCard D2", "SDCard Det",
- /* Bank GPIODV */
- "", "", "", "", "", "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "", "", "", "",
- "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
- "VDDEE Regulator", "VCCK Regulator",
- /* Bank GPIOY */
- "CON1 Header Pin7", "CON1 Header Pin11",
- "CON1 Header Pin13", "CON1 Header Pin15",
- "CON1 Header Pin18", "CON1 Header Pin19",
- "CON1 Header Pin22", "CON1 Header Pin21",
- "CON1 Header Pin24", "CON1 Header Pin23",
- "CON1 Header Pin26", "CON1 Header Pin29",
- "CON1 Header Pin32", "CON1 Header Pin8",
- "CON1 Header Pin10", "CON1 Header Pin16",
- "CON1 Header Pin12",
- /* Bank GPIOX */
- "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
- "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
- "WIFI Power Enable", "WIFI WAKE HOST",
- "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
- "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
- "Bluetooth UART TX", "Bluetooth UART RX",
- "Bluetooth UART CTS", "Bluetooth UART RTS",
- "", "", "", "WIFI 32K", "Bluetooth Enable",
- "Bluetooth WAKE HOST", "",
- /* Bank GPIOCLK */
- "", "CON1 Header Pin35", "", "";
-};
-
-&pwm_ef {
- status = "okay";
- pinctrl-0 = <&pwm_e_pins>;
- pinctrl-names = "default";
- clocks = <&clkc CLKID_FCLK_DIV4>;
- clock-names = "clkin0";
-};
-
-&saradc {
- status = "okay";
- vref-supply = <&vddio_ao18>;
-};
-
-/* SDIO */
-&sd_emmc_a {
- status = "okay";
- pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
- pinctrl-1 = <&sdio_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
- #address-cells = <1>;
- #size-cells = <0>;
-
- bus-width = <4>;
- cap-sd-highspeed;
- max-frequency = <50000000>;
-
- non-removable;
- disable-wp;
-
- /* WiFi firmware requires power to be kept while in suspend */
- keep-power-in-suspend;
-
- mmc-pwrseq = <&sdio_pwrseq>;
-
- vmmc-supply = <&vddio_ao3v3>;
- vqmmc-supply = <&vddio_ao18>;
-
- brcmf: wifi@1 {
- compatible = "brcm,bcm4329-fmac";
- reg = <1>;
- };
-};
-
-/* SD */
-&sd_emmc_b {
- status = "okay";
- pinctrl-0 = <&sdcard_pins>;
- pinctrl-1 = <&sdcard_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <4>;
- cap-sd-highspeed;
- sd-uhs-sdr12;
- sd-uhs-sdr25;
- sd-uhs-sdr50;
- sd-uhs-ddr50;
- max-frequency = <100000000>;
- disable-wp;
-
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
-
- vmmc-supply = <&vddio_ao3v3>;
- vqmmc-supply = <&vddio_tf>;
-};
-
-/* eMMC */
-&sd_emmc_c {
- status = "disabled";
- pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
- pinctrl-1 = <&emmc_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <8>;
- max-frequency = <200000000>;
- non-removable;
- disable-wp;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
-
- mmc-pwrseq = <&emmc_pwrseq>;
- vmmc-supply = <&vcc3v3>;
- vqmmc-supply = <&vcc1v8>;
-};
-
-/* DBG_UART */
-&uart_AO {
- status = "okay";
- pinctrl-0 = <&uart_ao_a_pins>;
- pinctrl-names = "default";
-};
-
-/* Bluetooth on AP6212 */
-&uart_A {
- status = "disabled";
- pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
- pinctrl-names = "default";
-};
-
-/* 40-pin CON1 */
-&uart_C {
- status = "disabled";
- pinctrl-0 = <&uart_c_pins>;
- pinctrl-names = "default";
-};
-
-&usb0_phy {
- status = "okay";
- phy-supply = <&vdd_5v>;
-};
-
-&usb1_phy {
- status = "okay";
-};
-
-&usb0 {
- status = "okay";
-};
-
-&usb1 {
- status = "okay";
-};
deleted file mode 100644
@@ -1,418 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2016 Andreas Färber
- * Copyright (c) 2016 BayLibre, Inc.
- * Author: Kevin Hilman <khilman@kernel.org>
- */
-
-/dts-v1/;
-
-#include "meson-gxbb.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/sound/meson-aiu.h>
-
-/ {
- compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
- model = "Hardkernel ODROID-C2";
-
- aliases {
- serial0 = &uart_AO;
- ethernet0 = ðmac;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0 0x80000000>;
- };
-
- usb_otg_pwr: regulator-usb-pwrs {
- compatible = "regulator-fixed";
-
- regulator-name = "USB_OTG_PWR";
-
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
-
- /*
- * signal name from schematics: PWREN
- */
- gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- /*
- * signal name from schematics: USB_POWER
- */
- vin-supply = <&p5v0>;
- };
-
- leds {
- compatible = "gpio-leds";
- led-blue {
- label = "c2:blue:alive";
- gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
- };
-
- p5v0: regulator-p5v0 {
- compatible = "regulator-fixed";
-
- regulator-name = "P5V0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
- hdmi_p5v0: regulator-hdmi_p5v0 {
- compatible = "regulator-fixed";
- regulator-name = "HDMI_P5V0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- /* AP2331SA-7 */
- vin-supply = <&p5v0>;
- };
-
- tflash_vdd: regulator-tflash_vdd {
- compatible = "regulator-fixed";
-
- regulator-name = "TFLASH_VDD";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- /*
- * signal name from schematics: TFLASH_VDD_EN
- */
- gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- /* U16 RT9179GB */
- vin-supply = <&vddio_ao3v3>;
- };
-
- tf_io: gpio-regulator-tf_io {
- compatible = "regulator-gpio";
-
- regulator-name = "TF_IO";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- /*
- * signal name from schematics: TF_3V3N_1V8_EN
- */
- gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
-
- states = <3300000 0>,
- <1800000 1>;
- /* U12/U13 RT9179GB */
- vin-supply = <&vddio_ao3v3>;
- };
-
- vcc1v8: regulator-vcc1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VCC1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- /* U18 RT9179GB */
- vin-supply = <&vddio_ao3v3>;
- };
-
- vcc3v3: regulator-vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vddio_ao1v8: regulator-vddio-ao1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VDDIO_AO1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- /* U17 RT9179GB */
- vin-supply = <&p5v0>;
- };
-
- vddio_ao3v3: regulator-vddio-ao3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VDDIO_AO3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- /* U11 MP2161GJ-C499 */
- vin-supply = <&p5v0>;
- };
-
- ddr3_1v5: regulator-ddr3_1v5 {
- compatible = "regulator-fixed";
- regulator-name = "DDR3_1V5";
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- /* U15 MP2161GJ-C499 */
- vin-supply = <&p5v0>;
- };
-
- emmc_pwrseq: emmc-pwrseq {
- compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
- };
-
- hdmi-connector {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&hdmi_tx_tmds_out>;
- };
- };
- };
-
- sound {
- compatible = "amlogic,gx-sound-card";
- model = "ODROID-C2";
- assigned-clocks = <&clkc CLKID_MPLL0>,
- <&clkc CLKID_MPLL1>,
- <&clkc CLKID_MPLL2>;
- assigned-clock-parents = <0>, <0>, <0>;
- assigned-clock-rates = <294912000>,
- <270950400>,
- <393216000>;
- status = "okay";
-
- dai-link-0 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
- };
-
- dai-link-1 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
- dai-format = "i2s";
- mclk-fs = <256>;
-
- codec-0 {
- sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
- };
- };
-
- dai-link-2 {
- sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
-
- codec-0 {
- sound-dai = <&hdmi_tx>;
- };
- };
- };
-};
-
-&aiu {
- status = "okay";
-};
-
-&cec_AO {
- status = "okay";
- pinctrl-0 = <&ao_cec_pins>;
- pinctrl-names = "default";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-ðmac {
- status = "okay";
- pinctrl-0 = <ð_rgmii_pins>;
- pinctrl-names = "default";
- phy-handle = <ð_phy0>;
- phy-mode = "rgmii";
-
- amlogic,tx-delay-ns = <2>;
-
- mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- eth_phy0: ethernet-phy@0 {
- /* Realtek RTL8211F (0x001cc916) */
- reg = <0>;
-
- reset-assert-us = <10000>;
- reset-deassert-us = <80000>;
- reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
-
- interrupt-parent = <&gpio_intc>;
- /* MAC_INTR on GPIOZ_15 */
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
- };
- };
-};
-
-&gpio_ao {
- /*
- * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
- * to be turned high in order to be detected by the USB Controller
- * This signal should be handled by a USB specific power sequence
- * in order to reset the Hub when USB bus is powered down.
- */
- hog-0 {
- gpio-hog;
- gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "usb-hub-reset";
- };
-};
-
-&hdmi_tx {
- status = "okay";
- pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
- pinctrl-names = "default";
- hdmi-supply = <&hdmi_p5v0>;
-};
-
-&hdmi_tx_tmds_port {
- hdmi_tx_tmds_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
-};
-
-&i2c_A {
- status = "okay";
- pinctrl-0 = <&i2c_a_pins>;
- pinctrl-names = "default";
-};
-
-&ir {
- status = "okay";
- pinctrl-0 = <&remote_input_ao_pins>;
- pinctrl-names = "default";
- linux,rc-map-name = "rc-odroid";
-};
-
-&gpio_ao {
- gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
- "USB HUB nRESET", "USB OTG Power En",
- "J7 Header Pin2", "IR In", "J7 Header Pin4",
- "J7 Header Pin6", "J7 Header Pin5", "J7 Header Pin7",
- "HDMI CEC", "SYS LED",
- /* GPIO_TEST_N */
- "";
-};
-
-&gpio {
- gpio-line-names = /* Bank GPIOZ */
- "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
- "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
- "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
- "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
- "Eth PHY nRESET", "Eth PHY Intc",
- /* Bank GPIOH */
- "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL", "",
- /* Bank BOOT */
- "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
- "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
- "eMMC Reset", "eMMC CMD",
- "", "", "", "", "", "", "",
- /* Bank CARD */
- "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
- "SDCard D3", "SDCard D2", "SDCard Det",
- /* Bank GPIODV */
- "", "", "", "", "", "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "", "", "", "",
- "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
- "PWM D", "PWM B",
- /* Bank GPIOY */
- "Revision Bit0", "Revision Bit1", "",
- "J2 Header Pin35", "", "", "", "J2 Header Pin36",
- "J2 Header Pin31", "", "", "", "TF VDD En",
- "J2 Header Pin32", "J2 Header Pin26", "", "",
- /* Bank GPIOX */
- "J2 Header Pin29", "J2 Header Pin24",
- "J2 Header Pin23", "J2 Header Pin22",
- "J2 Header Pin21", "J2 Header Pin18",
- "J2 Header Pin33", "J2 Header Pin19",
- "J2 Header Pin16", "J2 Header Pin15",
- "J2 Header Pin12", "J2 Header Pin13",
- "J2 Header Pin8", "J2 Header Pin10",
- "", "", "", "", "",
- "J2 Header Pin11", "", "J2 Header Pin7", "",
- /* Bank GPIOCLK */
- "", "", "", "";
-};
-
-&saradc {
- status = "okay";
- vref-supply = <&vcc1v8>;
-};
-
-&scpi_clocks {
- status = "disabled";
-};
-
-/* SD */
-&sd_emmc_b {
- status = "okay";
- pinctrl-0 = <&sdcard_pins>;
- pinctrl-1 = <&sdcard_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <4>;
- cap-sd-highspeed;
- sd-uhs-sdr12;
- sd-uhs-sdr25;
- sd-uhs-sdr50;
- sd-uhs-ddr50;
- max-frequency = <100000000>;
- disable-wp;
-
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
-
- vmmc-supply = <&tflash_vdd>;
- vqmmc-supply = <&tf_io>;
-};
-
-/* eMMC */
-&sd_emmc_c {
- status = "okay";
- pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
- pinctrl-1 = <&emmc_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <8>;
- max-frequency = <200000000>;
- non-removable;
- disable-wp;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
-
- mmc-pwrseq = <&emmc_pwrseq>;
- vmmc-supply = <&vcc3v3>;
- vqmmc-supply = <&vcc1v8>;
-};
-
-&uart_AO {
- status = "okay";
- pinctrl-0 = <&uart_ao_a_pins>;
- pinctrl-names = "default";
-};
-
-&usb0_phy {
- status = "disabled";
- phy-supply = <&usb_otg_pwr>;
-};
-
-&usb1_phy {
- status = "okay";
- phy-supply = <&usb_otg_pwr>;
-};
-
-&usb0 {
- status = "disabled";
-};
-
-&usb1 {
- status = "okay";
-};
deleted file mode 100644
@@ -1,100 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2016 Andreas Färber
- * Copyright (c) 2016 BayLibre, Inc.
- * Author: Kevin Hilman <khilman@kernel.org>
- */
-
-/dts-v1/;
-
-#include "meson-gxbb-p20x.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
- compatible = "amlogic,p200", "amlogic,meson-gxbb";
- model = "Amlogic Meson GXBB P200 Development Board";
-
- avdd18_usb_adc: regulator-avdd18_usb_adc {
- compatible = "regulator-fixed";
- regulator-name = "AVDD18_USB_ADC";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- adc_keys {
- compatible = "adc-keys";
- io-channels = <&saradc 0>;
- io-channel-names = "buttons";
- keyup-threshold-microvolt = <1800000>;
-
- button-home {
- label = "Home";
- linux,code = <KEY_HOME>;
- press-threshold-microvolt = <900000>; /* 50% */
- };
-
- button-esc {
- label = "Esc";
- linux,code = <KEY_ESC>;
- press-threshold-microvolt = <684000>; /* 38% */
- };
-
- button-up {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- press-threshold-microvolt = <468000>; /* 26% */
- };
-
- button-down {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- press-threshold-microvolt = <252000>; /* 14% */
- };
-
- button-menu {
- label = "Menu";
- linux,code = <KEY_MENU>;
- press-threshold-microvolt = <0>; /* 0% */
- };
- };
-};
-
-ðmac {
- status = "okay";
- pinctrl-0 = <ð_rgmii_pins>;
- pinctrl-names = "default";
- phy-handle = <ð_phy0>;
- phy-mode = "rgmii";
-
- amlogic,tx-delay-ns = <2>;
-
- mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- eth_phy0: ethernet-phy@3 {
- /* Micrel KSZ9031 (0x00221620) */
- reg = <3>;
-
- reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
- reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
-
- interrupt-parent = <&gpio_intc>;
- /* MAC_INTR on GPIOZ_15 */
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
- };
- };
-};
-
-&i2c_B {
- status = "okay";
- pinctrl-0 = <&i2c_b_pins>;
- pinctrl-names = "default";
-};
-
-&saradc {
- status = "okay";
- vref-supply = <&avdd18_usb_adc>;
-};
deleted file mode 100644
@@ -1,26 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2016 Andreas Färber
- * Copyright (c) 2016 BayLibre, Inc.
- * Author: Kevin Hilman <khilman@kernel.org>
- */
-
-/dts-v1/;
-
-#include "meson-gxbb-p20x.dtsi"
-
-/ {
- compatible = "amlogic,p201", "amlogic,meson-gxbb";
- model = "Amlogic Meson GXBB P201 Development Board";
-};
-
-ðmac {
- status = "okay";
- pinctrl-0 = <ð_rmii_pins>;
- pinctrl-names = "default";
- phy-mode = "rmii";
-
- snps,reset-gpio = <&gpio GPIOZ_14 0>;
- snps,reset-delays-us = <0>, <10000>, <1000000>;
- snps,reset-active-low;
-};
deleted file mode 100644
@@ -1,250 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2016 Andreas Färber
- * Copyright (c) 2016 BayLibre, Inc.
- * Author: Kevin Hilman <khilman@kernel.org>
- */
-
-#include "meson-gxbb.dtsi"
-
-/ {
- aliases {
- serial0 = &uart_AO;
- ethernet0 = ðmac;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0 0x40000000>;
- };
-
- usb_pwr: regulator-usb-pwrs {
- compatible = "regulator-fixed";
-
- regulator-name = "USB_PWR";
-
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
-
- /* signal name in schematic: USB_PWR_EN */
- gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vddio_card: gpio-regulator {
- compatible = "regulator-gpio";
-
- regulator-name = "VDDIO_CARD";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
-
- /* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
- states = <1800000 0>,
- <3300000 1>;
-
- regulator-settling-time-up-us = <10000>;
- regulator-settling-time-down-us = <150000>;
- };
-
- vddio_boot: regulator-vddio_boot {
- compatible = "regulator-fixed";
- regulator-name = "VDDIO_BOOT";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vddao_3v3: regulator-vddao_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VDDAO_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vcc_3v3: regulator-vcc_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- emmc_pwrseq: emmc-pwrseq {
- compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
- };
-
- wifi32k: wifi32k {
- compatible = "pwm-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
- };
-
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
- clocks = <&wifi32k>;
- clock-names = "ext_clock";
- };
-
- cvbs_connector: cvbs-connector {
- compatible = "composite-video-connector";
-
- port {
- cvbs_connector_in: endpoint {
- remote-endpoint = <&cvbs_vdac_out>;
- };
- };
- };
-
- hdmi-connector {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&hdmi_tx_tmds_out>;
- };
- };
- };
-};
-
-&cec_AO {
- status = "okay";
- pinctrl-0 = <&ao_cec_pins>;
- pinctrl-names = "default";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-&cvbs_vdac_port {
- cvbs_vdac_out: endpoint {
- remote-endpoint = <&cvbs_connector_in>;
- };
-};
-
-&hdmi_tx {
- status = "okay";
- pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
- pinctrl-names = "default";
-};
-
-&hdmi_tx_tmds_port {
- hdmi_tx_tmds_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
-};
-
-&ir {
- status = "okay";
- pinctrl-0 = <&remote_input_ao_pins>;
- pinctrl-names = "default";
-};
-
-&pwm_ef {
- status = "okay";
- pinctrl-0 = <&pwm_e_pins>;
- pinctrl-names = "default";
- clocks = <&clkc CLKID_FCLK_DIV4>;
- clock-names = "clkin0";
-};
-
-/* Wireless SDIO Module */
-&sd_emmc_a {
- status = "okay";
- pinctrl-0 = <&sdio_pins>;
- pinctrl-1 = <&sdio_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
- #address-cells = <1>;
- #size-cells = <0>;
-
- bus-width = <4>;
- cap-sd-highspeed;
- max-frequency = <50000000>;
-
- non-removable;
- disable-wp;
-
- /* WiFi firmware requires power to be kept while in suspend */
- keep-power-in-suspend;
-
- mmc-pwrseq = <&sdio_pwrseq>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddio_boot>;
-
- brcmf: wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-/* SD card */
-&sd_emmc_b {
- status = "okay";
- pinctrl-0 = <&sdcard_pins>;
- pinctrl-1 = <&sdcard_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <4>;
- cap-sd-highspeed;
- sd-uhs-sdr12;
- sd-uhs-sdr25;
- sd-uhs-sdr50;
- max-frequency = <100000000>;
- disable-wp;
-
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddio_card>;
-};
-
-/* eMMC */
-&sd_emmc_c {
- status = "okay";
- pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
- pinctrl-1 = <&emmc_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <8>;
- cap-mmc-highspeed;
- max-frequency = <200000000>;
- non-removable;
- disable-wp;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
-
- mmc-pwrseq = <&emmc_pwrseq>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&vddio_boot>;
-};
-
-/* This UART is brought out to the DB9 connector */
-&uart_AO {
- status = "okay";
- pinctrl-0 = <&uart_ao_a_pins>;
- pinctrl-names = "default";
-};
-
-&usb0_phy {
- status = "okay";
- phy-supply = <&usb_pwr>;
-};
-
-&usb1_phy {
- status = "okay";
-};
-
-&usb0 {
- status = "okay";
-};
-
-&usb1 {
- status = "okay";
-};
deleted file mode 100644
@@ -1,58 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2016 BayLibre, Inc.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- */
-
-/dts-v1/;
-
-#include "meson-gxbb-wetek.dtsi"
-#include <dt-bindings/sound/meson-aiu.h>
-
-/ {
- compatible = "wetek,hub", "amlogic,meson-gxbb";
- model = "WeTek Hub";
-
- sound {
- compatible = "amlogic,gx-sound-card";
- model = "WETEK-HUB";
- assigned-clocks = <&clkc CLKID_MPLL0>,
- <&clkc CLKID_MPLL1>,
- <&clkc CLKID_MPLL2>;
- assigned-clock-parents = <0>, <0>, <0>;
- assigned-clock-rates = <294912000>,
- <270950400>,
- <393216000>;
- status = "okay";
-
- dai-link-0 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
- };
-
- dai-link-1 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
- dai-format = "i2s";
- mclk-fs = <256>;
-
- codec-0 {
- sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
- };
- };
-
- dai-link-2 {
- sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
-
- codec-0 {
- sound-dai = <&hdmi_tx>;
- };
- };
- };
-};
-
-&aiu {
- status = "okay";
-};
-
-&ir {
- linux,rc-map-name = "rc-wetek-hub";
-};
deleted file mode 100644
@@ -1,119 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2016 BayLibre, Inc.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- */
-
-/dts-v1/;
-
-#include "meson-gxbb-wetek.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/sound/meson-aiu.h>
-
-/ {
- compatible = "wetek,play2", "amlogic,meson-gxbb";
- model = "WeTek Play 2";
-
- spdif_dit: audio-codec-0 {
- #sound-dai-cells = <0>;
- compatible = "linux,spdif-dit";
- status = "okay";
- sound-name-prefix = "DIT";
- };
-
- leds {
- led-wifi {
- label = "wetek-play:wifi-status";
- gpios = <&gpio GPIODV_26 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- led-ethernet {
- label = "wetek-play:ethernet-status";
- gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- gpio-keys-polled {
- compatible = "gpio-keys-polled";
- poll-interval = <100>;
-
- button {
- label = "reset";
- linux,code = <KEY_RESTART>;
- gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
- };
- };
-
- sound {
- compatible = "amlogic,gx-sound-card";
- model = "WETEK-PLAY2";
- assigned-clocks = <&clkc CLKID_MPLL0>,
- <&clkc CLKID_MPLL1>,
- <&clkc CLKID_MPLL2>;
- assigned-clock-parents = <0>, <0>, <0>;
- assigned-clock-rates = <294912000>,
- <270950400>,
- <393216000>;
- status = "okay";
-
- dai-link-0 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
- };
-
- dai-link-1 {
- sound-dai = <&aiu AIU_CPU CPU_SPDIF_FIFO>;
- };
-
- dai-link-2 {
- sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
- dai-format = "i2s";
- mclk-fs = <256>;
-
- codec-0 {
- sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
- };
- };
-
- dai-link-3 {
- sound-dai = <&aiu AIU_CPU CPU_SPDIF_ENCODER>;
-
- codec-0 {
- sound-dai = <&spdif_dit>;
- };
- };
-
- dai-link-4 {
- sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
-
- codec-0 {
- sound-dai = <&hdmi_tx>;
- };
- };
- };
-};
-
-&aiu {
- status = "okay";
- pinctrl-0 = <&spdif_out_y_pins>;
- pinctrl-names = "default";
-};
-
-&i2c_A {
- status = "okay";
- pinctrl-0 = <&i2c_a_pins>;
- pinctrl-names = "default";
-};
-
-&usb1_phy {
- status = "okay";
-};
-
-&usb1 {
- status = "okay";
-};
-
-&ir {
- linux,rc-map-name = "rc-wetek-play2";
-};
deleted file mode 100644
@@ -1,292 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2016 Andreas Färber
- * Copyright (c) 2016 BayLibre, Inc.
- * Author: Kevin Hilman <khilman@kernel.org>
- */
-
-#include "meson-gxbb.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- aliases {
- serial0 = &uart_AO;
- ethernet0 = ðmac;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0 0x40000000>;
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-power {
- /* red in suspend or power-off */
- color = <LED_COLOR_ID_BLUE>;
- function = LED_FUNCTION_POWER;
- gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- panic-indicator;
- };
- };
-
- usb_pwr: regulator-usb-pwrs {
- compatible = "regulator-fixed";
-
- regulator-name = "USB_PWR";
-
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
-
- gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vddio_boot: regulator-vddio_boot {
- compatible = "regulator-fixed";
- regulator-name = "VDDIO_BOOT";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vddao_3v3: regulator-vddao_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VDDAO_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vddio_ao18: regulator-vddio_ao18 {
- compatible = "regulator-fixed";
- regulator-name = "VDDIO_AO18";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- vcc_3v3: regulator-vcc_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- emmc_pwrseq: emmc-pwrseq {
- compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
- };
-
- wifi32k: wifi32k {
- compatible = "pwm-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
- };
-
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
- clocks = <&wifi32k>;
- clock-names = "ext_clock";
- };
-
- cvbs-connector {
- compatible = "composite-video-connector";
-
- port {
- cvbs_connector_in: endpoint {
- remote-endpoint = <&cvbs_vdac_out>;
- };
- };
- };
-
- hdmi-connector {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&hdmi_tx_tmds_out>;
- };
- };
- };
-};
-
-&cec_AO {
- status = "okay";
- pinctrl-0 = <&ao_cec_pins>;
- pinctrl-names = "default";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-&cvbs_vdac_port {
- cvbs_vdac_out: endpoint {
- remote-endpoint = <&cvbs_connector_in>;
- };
-};
-
-ðmac {
- status = "okay";
- pinctrl-0 = <ð_rgmii_pins>;
- pinctrl-names = "default";
-
- phy-handle = <ð_phy0>;
- phy-mode = "rgmii";
-
- amlogic,tx-delay-ns = <2>;
-
- mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- eth_phy0: ethernet-phy@0 {
- /* Realtek RTL8211F (0x001cc916) */
- reg = <0>;
-
- reset-assert-us = <10000>;
- reset-deassert-us = <80000>;
- reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
-
- interrupt-parent = <&gpio_intc>;
- /* MAC_INTR on GPIOZ_15 */
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
- };
- };
-};
-
-&hdmi_tx {
- status = "okay";
- pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
- pinctrl-names = "default";
- hdmi-supply = <&vddio_ao18>;
-};
-
-&hdmi_tx_tmds_port {
- hdmi_tx_tmds_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
-};
-
-&ir {
- status = "okay";
- pinctrl-0 = <&remote_input_ao_pins>;
- pinctrl-names = "default";
-};
-
-&pwm_ef {
- status = "okay";
- pinctrl-0 = <&pwm_e_pins>;
- pinctrl-names = "default";
- clocks = <&clkc CLKID_FCLK_DIV4>;
- clock-names = "clkin0";
-};
-
-&saradc {
- status = "okay";
- vref-supply = <&vddio_ao18>;
-};
-
-/* Wireless SDIO Module */
-&sd_emmc_a {
- status = "okay";
- pinctrl-0 = <&sdio_pins>;
- pinctrl-1 = <&sdio_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
- #address-cells = <1>;
- #size-cells = <0>;
-
- bus-width = <4>;
- cap-sd-highspeed;
- max-frequency = <50000000>;
-
- non-removable;
- disable-wp;
-
- /* WiFi firmware requires power to be kept while in suspend */
- keep-power-in-suspend;
-
- mmc-pwrseq = <&sdio_pwrseq>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddio_boot>;
-
- brcmf: wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-/* SD card */
-&sd_emmc_b {
- status = "okay";
- pinctrl-0 = <&sdcard_pins>;
- pinctrl-1 = <&sdcard_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <4>;
- cap-sd-highspeed;
- max-frequency = <50000000>;
- disable-wp;
-
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vcc_3v3>;
-};
-
-/* eMMC */
-&sd_emmc_c {
- status = "okay";
- pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
- pinctrl-1 = <&emmc_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <8>;
- cap-mmc-highspeed;
- max-frequency = <200000000>;
- non-removable;
- disable-wp;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
-
- mmc-pwrseq = <&emmc_pwrseq>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&vddio_boot>;
-};
-
-/* This is connected to the Bluetooth module: */
-&uart_A {
- status = "okay";
- pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
- pinctrl-names = "default";
- uart-has-rtscts;
-
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
- };
-};
-
-/* This UART is brought out to the DB9 connector */
-&uart_AO {
- status = "okay";
- pinctrl-0 = <&uart_ao_a_pins>;
- pinctrl-names = "default";
-};
-
-&usb0_phy {
- status = "okay";
- phy-supply = <&usb_pwr>;
-};
-
-&usb0 {
- status = "okay";
-};
deleted file mode 100644
@@ -1,856 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2016 Andreas Färber
- */
-
-#include "meson-gx.dtsi"
-#include "meson-gx-mali450.dtsi"
-#include <dt-bindings/gpio/meson-gxbb-gpio.h>
-#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
-#include <dt-bindings/clock/gxbb-clkc.h>
-#include <dt-bindings/clock/gxbb-aoclkc.h>
-#include <dt-bindings/reset/gxbb-aoclkc.h>
-
-/ {
- compatible = "amlogic,meson-gxbb";
-
- soc {
- usb0_phy: phy@c0000000 {
- compatible = "amlogic,meson-gxbb-usb2-phy";
- #phy-cells = <0>;
- reg = <0x0 0xc0000000 0x0 0x20>;
- resets = <&reset RESET_USB_OTG>;
- clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>;
- clock-names = "usb_general", "usb";
- status = "disabled";
- };
-
- usb1_phy: phy@c0000020 {
- compatible = "amlogic,meson-gxbb-usb2-phy";
- #phy-cells = <0>;
- reg = <0x0 0xc0000020 0x0 0x20>;
- resets = <&reset RESET_USB_OTG>;
- clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>;
- clock-names = "usb_general", "usb";
- status = "disabled";
- };
-
- usb0: usb@c9000000 {
- compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
- reg = <0x0 0xc9000000 0x0 0x40000>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clkc CLKID_USB0_DDR_BRIDGE>;
- clock-names = "otg";
- phys = <&usb0_phy>;
- phy-names = "usb2-phy";
- dr_mode = "host";
- status = "disabled";
- };
-
- usb1: usb@c9100000 {
- compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
- reg = <0x0 0xc9100000 0x0 0x40000>;
- interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
- clock-names = "otg";
- phys = <&usb1_phy>;
- phy-names = "usb2-phy";
- dr_mode = "host";
- status = "disabled";
- };
- };
-};
-
-&aiu {
- compatible = "amlogic,aiu-gxbb", "amlogic,aiu";
- clocks = <&clkc CLKID_AIU_GLUE>,
- <&clkc CLKID_I2S_OUT>,
- <&clkc CLKID_AOCLK_GATE>,
- <&clkc CLKID_CTS_AMCLK>,
- <&clkc CLKID_MIXER_IFACE>,
- <&clkc CLKID_IEC958>,
- <&clkc CLKID_IEC958_GATE>,
- <&clkc CLKID_CTS_MCLK_I958>,
- <&clkc CLKID_CTS_I958>;
- clock-names = "pclk",
- "i2s_pclk",
- "i2s_aoclk",
- "i2s_mclk",
- "i2s_mixer",
- "spdif_pclk",
- "spdif_aoclk",
- "spdif_mclk",
- "spdif_mclk_sel";
- resets = <&reset RESET_AIU>;
-};
-
-&aobus {
- pinctrl_aobus: pinctrl@14 {
- compatible = "amlogic,meson-gxbb-aobus-pinctrl";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- gpio_ao: bank@14 {
- reg = <0x0 0x00014 0x0 0x8>,
- <0x0 0x0002c 0x0 0x4>,
- <0x0 0x00024 0x0 0x8>;
- reg-names = "mux", "pull", "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&pinctrl_aobus 0 0 14>;
- };
-
- uart_ao_a_pins: uart_ao_a {
- mux {
- groups = "uart_tx_ao_a", "uart_rx_ao_a";
- function = "uart_ao";
- bias-disable;
- };
- };
-
- uart_ao_a_cts_rts_pins: uart_ao_a_cts_rts {
- mux {
- groups = "uart_cts_ao_a",
- "uart_rts_ao_a";
- function = "uart_ao";
- bias-disable;
- };
- };
-
- uart_ao_b_pins: uart_ao_b {
- mux {
- groups = "uart_tx_ao_b", "uart_rx_ao_b";
- function = "uart_ao_b";
- bias-disable;
- };
- };
-
- uart_ao_b_cts_rts_pins: uart_ao_b_cts_rts {
- mux {
- groups = "uart_cts_ao_b",
- "uart_rts_ao_b";
- function = "uart_ao_b";
- bias-disable;
- };
- };
-
- remote_input_ao_pins: remote_input_ao {
- mux {
- groups = "remote_input_ao";
- function = "remote_input_ao";
- bias-disable;
- };
- };
-
- i2c_ao_pins: i2c_ao {
- mux {
- groups = "i2c_sck_ao",
- "i2c_sda_ao";
- function = "i2c_ao";
- bias-disable;
- };
- };
-
- pwm_ao_a_3_pins: pwm_ao_a_3 {
- mux {
- groups = "pwm_ao_a_3";
- function = "pwm_ao_a_3";
- bias-disable;
- };
- };
-
- pwm_ao_a_6_pins: pwm_ao_a_6 {
- mux {
- groups = "pwm_ao_a_6";
- function = "pwm_ao_a_6";
- bias-disable;
- };
- };
-
- pwm_ao_a_12_pins: pwm_ao_a_12 {
- mux {
- groups = "pwm_ao_a_12";
- function = "pwm_ao_a_12";
- bias-disable;
- };
- };
-
- pwm_ao_b_pins: pwm_ao_b {
- mux {
- groups = "pwm_ao_b";
- function = "pwm_ao_b";
- bias-disable;
- };
- };
-
- i2s_am_clk_pins: i2s_am_clk {
- mux {
- groups = "i2s_am_clk";
- function = "i2s_out_ao";
- bias-disable;
- };
- };
-
- i2s_out_ao_clk_pins: i2s_out_ao_clk {
- mux {
- groups = "i2s_out_ao_clk";
- function = "i2s_out_ao";
- bias-disable;
- };
- };
-
- i2s_out_lr_clk_pins: i2s_out_lr_clk {
- mux {
- groups = "i2s_out_lr_clk";
- function = "i2s_out_ao";
- bias-disable;
- };
- };
-
- i2s_out_ch01_ao_pins: i2s_out_ch01_ao {
- mux {
- groups = "i2s_out_ch01_ao";
- function = "i2s_out_ao";
- bias-disable;
- };
- };
-
- i2s_out_ch23_ao_pins: i2s_out_ch23_ao {
- mux {
- groups = "i2s_out_ch23_ao";
- function = "i2s_out_ao";
- bias-disable;
- };
- };
-
- i2s_out_ch45_ao_pins: i2s_out_ch45_ao {
- mux {
- groups = "i2s_out_ch45_ao";
- function = "i2s_out_ao";
- bias-disable;
- };
- };
-
- spdif_out_ao_6_pins: spdif_out_ao_6 {
- mux {
- groups = "spdif_out_ao_6";
- function = "spdif_out_ao";
- };
- };
-
- spdif_out_ao_13_pins: spdif_out_ao_13 {
- mux {
- groups = "spdif_out_ao_13";
- function = "spdif_out_ao";
- bias-disable;
- };
- };
-
- ao_cec_pins: ao_cec {
- mux {
- groups = "ao_cec";
- function = "cec_ao";
- bias-disable;
- };
- };
-
- ee_cec_pins: ee_cec {
- mux {
- groups = "ee_cec";
- function = "cec_ao";
- bias-disable;
- };
- };
- };
-};
-
-&cbus {
- spifc: spi@8c80 {
- compatible = "amlogic,meson-gxbb-spifc";
- reg = <0x0 0x08c80 0x0 0x80>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clkc CLKID_SPI>;
- status = "disabled";
- };
-};
-
-&cec_AO {
- clocks = <&clkc_AO CLKID_AO_CEC_32K>;
- clock-names = "core";
-};
-
-&clkc_AO {
- compatible = "amlogic,meson-gxbb-aoclkc", "amlogic,meson-gx-aoclkc";
- clocks = <&xtal>, <&clkc CLKID_CLK81>;
- clock-names = "xtal", "mpeg-clk";
-};
-
-&efuse {
- clocks = <&clkc CLKID_EFUSE>;
-};
-
-ðmac {
- clocks = <&clkc CLKID_ETH>,
- <&clkc CLKID_FCLK_DIV2>,
- <&clkc CLKID_MPLL2>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "stmmaceth", "clkin0", "clkin1", "timing-adjustment";
-};
-
-&gpio_intc {
- compatible = "amlogic,meson-gpio-intc",
- "amlogic,meson-gxbb-gpio-intc";
- status = "okay";
-};
-
-&hdmi_tx {
- compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
- resets = <&reset RESET_HDMITX_CAPB3>,
- <&reset RESET_HDMI_SYSTEM_RESET>,
- <&reset RESET_HDMI_TX>;
- reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
- clocks = <&clkc CLKID_HDMI_PCLK>,
- <&clkc CLKID_CLK81>,
- <&clkc CLKID_GCLK_VENCI_INT0>;
- clock-names = "isfr", "iahb", "venci";
-};
-
-&sysctrl {
- clkc: clock-controller {
- compatible = "amlogic,gxbb-clkc";
- #clock-cells = <1>;
- clocks = <&xtal>;
- clock-names = "xtal";
- };
-};
-
-&hwrng {
- clocks = <&clkc CLKID_RNG0>;
- clock-names = "core";
-};
-
-&i2c_A {
- clocks = <&clkc CLKID_I2C>;
-};
-
-&i2c_AO {
- clocks = <&clkc CLKID_AO_I2C>;
-};
-
-&i2c_B {
- clocks = <&clkc CLKID_I2C>;
-};
-
-&i2c_C {
- clocks = <&clkc CLKID_I2C>;
-};
-
-&mali {
- compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
-
- clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
- clock-names = "bus", "core";
-
- assigned-clocks = <&clkc CLKID_GP0_PLL>;
- assigned-clock-rates = <744000000>;
-};
-
-&periphs {
- pinctrl_periphs: pinctrl@4b0 {
- compatible = "amlogic,meson-gxbb-periphs-pinctrl";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- gpio: bank@4b0 {
- reg = <0x0 0x004b0 0x0 0x28>,
- <0x0 0x004e8 0x0 0x14>,
- <0x0 0x00520 0x0 0x14>,
- <0x0 0x00430 0x0 0x40>;
- reg-names = "mux", "pull", "pull-enable", "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&pinctrl_periphs 0 0 119>;
- };
-
- emmc_pins: emmc {
- mux-0 {
- groups = "emmc_nand_d07",
- "emmc_cmd";
- function = "emmc";
- bias-pull-up;
- };
-
- mux-1 {
- groups = "emmc_clk";
- function = "emmc";
- bias-disable;
- };
- };
-
- emmc_ds_pins: emmc-ds {
- mux {
- groups = "emmc_ds";
- function = "emmc";
- bias-pull-down;
- };
- };
-
- emmc_clk_gate_pins: emmc_clk_gate {
- mux {
- groups = "BOOT_8";
- function = "gpio_periphs";
- bias-pull-down;
- };
- };
-
- nor_pins: nor {
- mux {
- groups = "nor_d",
- "nor_q",
- "nor_c",
- "nor_cs";
- function = "nor";
- bias-disable;
- };
- };
-
- spi_pins: spi-pins {
- mux {
- groups = "spi_miso",
- "spi_mosi",
- "spi_sclk";
- function = "spi";
- bias-disable;
- };
- };
-
- spi_ss0_pins: spi-ss0 {
- mux {
- groups = "spi_ss0";
- function = "spi";
- bias-disable;
- };
- };
-
- sdcard_pins: sdcard {
- mux-0 {
- groups = "sdcard_d0",
- "sdcard_d1",
- "sdcard_d2",
- "sdcard_d3",
- "sdcard_cmd";
- function = "sdcard";
- bias-pull-up;
- };
-
- mux-1 {
- groups = "sdcard_clk";
- function = "sdcard";
- bias-disable;
- };
- };
-
- sdcard_clk_gate_pins: sdcard_clk_gate {
- mux {
- groups = "CARD_2";
- function = "gpio_periphs";
- bias-pull-down;
- };
- };
-
- sdio_pins: sdio {
- mux-0 {
- groups = "sdio_d0",
- "sdio_d1",
- "sdio_d2",
- "sdio_d3",
- "sdio_cmd";
- function = "sdio";
- bias-pull-up;
- };
-
- mux-1 {
- groups = "sdio_clk";
- function = "sdio";
- bias-disable;
- };
- };
-
- sdio_clk_gate_pins: sdio_clk_gate {
- mux {
- groups = "GPIOX_4";
- function = "gpio_periphs";
- bias-pull-down;
- };
- };
-
- sdio_irq_pins: sdio_irq {
- mux {
- groups = "sdio_irq";
- function = "sdio";
- bias-disable;
- };
- };
-
- uart_a_pins: uart_a {
- mux {
- groups = "uart_tx_a",
- "uart_rx_a";
- function = "uart_a";
- bias-disable;
- };
- };
-
- uart_a_cts_rts_pins: uart_a_cts_rts {
- mux {
- groups = "uart_cts_a",
- "uart_rts_a";
- function = "uart_a";
- bias-disable;
- };
- };
-
- uart_b_pins: uart_b {
- mux {
- groups = "uart_tx_b",
- "uart_rx_b";
- function = "uart_b";
- bias-disable;
- };
- };
-
- uart_b_cts_rts_pins: uart_b_cts_rts {
- mux {
- groups = "uart_cts_b",
- "uart_rts_b";
- function = "uart_b";
- bias-disable;
- };
- };
-
- uart_c_pins: uart_c {
- mux {
- groups = "uart_tx_c",
- "uart_rx_c";
- function = "uart_c";
- bias-disable;
- };
- };
-
- uart_c_cts_rts_pins: uart_c_cts_rts {
- mux {
- groups = "uart_cts_c",
- "uart_rts_c";
- function = "uart_c";
- bias-disable;
- };
- };
-
- i2c_a_pins: i2c_a {
- mux {
- groups = "i2c_sck_a",
- "i2c_sda_a";
- function = "i2c_a";
- bias-disable;
- };
- };
-
- i2c_b_pins: i2c_b {
- mux {
- groups = "i2c_sck_b",
- "i2c_sda_b";
- function = "i2c_b";
- bias-disable;
- };
- };
-
- i2c_c_pins: i2c_c {
- mux {
- groups = "i2c_sck_c",
- "i2c_sda_c";
- function = "i2c_c";
- bias-disable;
- };
- };
-
- eth_rgmii_pins: eth-rgmii {
- mux {
- groups = "eth_mdio",
- "eth_mdc",
- "eth_clk_rx_clk",
- "eth_rx_dv",
- "eth_rxd0",
- "eth_rxd1",
- "eth_rxd2",
- "eth_rxd3",
- "eth_rgmii_tx_clk",
- "eth_tx_en",
- "eth_txd0",
- "eth_txd1",
- "eth_txd2",
- "eth_txd3";
- function = "eth";
- bias-disable;
- };
- };
-
- eth_rmii_pins: eth-rmii {
- mux {
- groups = "eth_mdio",
- "eth_mdc",
- "eth_clk_rx_clk",
- "eth_rx_dv",
- "eth_rxd0",
- "eth_rxd1",
- "eth_tx_en",
- "eth_txd0",
- "eth_txd1";
- function = "eth";
- bias-disable;
- };
- };
-
- pwm_a_x_pins: pwm_a_x {
- mux {
- groups = "pwm_a_x";
- function = "pwm_a_x";
- bias-disable;
- };
- };
-
- pwm_a_y_pins: pwm_a_y {
- mux {
- groups = "pwm_a_y";
- function = "pwm_a_y";
- bias-disable;
- };
- };
-
- pwm_b_pins: pwm_b {
- mux {
- groups = "pwm_b";
- function = "pwm_b";
- bias-disable;
- };
- };
-
- pwm_d_pins: pwm_d {
- mux {
- groups = "pwm_d";
- function = "pwm_d";
- bias-disable;
- };
- };
-
- pwm_e_pins: pwm_e {
- mux {
- groups = "pwm_e";
- function = "pwm_e";
- bias-disable;
- };
- };
-
- pwm_f_x_pins: pwm_f_x {
- mux {
- groups = "pwm_f_x";
- function = "pwm_f_x";
- bias-disable;
- };
- };
-
- pwm_f_y_pins: pwm_f_y {
- mux {
- groups = "pwm_f_y";
- function = "pwm_f_y";
- bias-disable;
- };
- };
-
- hdmi_hpd_pins: hdmi_hpd {
- mux {
- groups = "hdmi_hpd";
- function = "hdmi_hpd";
- bias-disable;
- };
- };
-
- hdmi_i2c_pins: hdmi_i2c {
- mux {
- groups = "hdmi_sda", "hdmi_scl";
- function = "hdmi_i2c";
- bias-disable;
- };
- };
-
- i2sout_ch23_y_pins: i2sout_ch23_y {
- mux {
- groups = "i2sout_ch23_y";
- function = "i2s_out";
- bias-disable;
- };
- };
-
- i2sout_ch45_y_pins: i2sout_ch45_y {
- mux {
- groups = "i2sout_ch45_y";
- function = "i2s_out";
- bias-disable;
- };
- };
-
- i2sout_ch67_y_pins: i2sout_ch67_y {
- mux {
- groups = "i2sout_ch67_y";
- function = "i2s_out";
- bias-disable;
- };
- };
-
- spdif_out_y_pins: spdif_out_y {
- mux {
- groups = "spdif_out_y";
- function = "spdif_out";
- bias-disable;
- };
- };
- };
-};
-
-&pwrc {
- resets = <&reset RESET_VIU>,
- <&reset RESET_VENC>,
- <&reset RESET_VCBUS>,
- <&reset RESET_BT656>,
- <&reset RESET_DVIN_RESET>,
- <&reset RESET_RDMA>,
- <&reset RESET_VENCI>,
- <&reset RESET_VENCP>,
- <&reset RESET_VDAC>,
- <&reset RESET_VDI6>,
- <&reset RESET_VENCL>,
- <&reset RESET_VID_LOCK>;
- reset-names = "viu", "venc", "vcbus", "bt656",
- "dvin", "rdma", "venci", "vencp",
- "vdac", "vdi6", "vencl", "vid_lock";
- clocks = <&clkc CLKID_VPU>,
- <&clkc CLKID_VAPB>;
- clock-names = "vpu", "vapb";
- /*
- * VPU clocking is provided by two identical clock paths
- * VPU_0 and VPU_1 muxed to a single clock by a glitch
- * free mux to safely change frequency while running.
- * Same for VAPB but with a final gate after the glitch free mux.
- */
- assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
- <&clkc CLKID_VPU_0>,
- <&clkc CLKID_VPU>, /* Glitch free mux */
- <&clkc CLKID_VAPB_0_SEL>,
- <&clkc CLKID_VAPB_0>,
- <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
- assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
- <0>, /* Do Nothing */
- <&clkc CLKID_VPU_0>,
- <&clkc CLKID_FCLK_DIV4>,
- <0>, /* Do Nothing */
- <&clkc CLKID_VAPB_0>;
- assigned-clock-rates = <0>, /* Do Nothing */
- <666666666>,
- <0>, /* Do Nothing */
- <0>, /* Do Nothing */
- <250000000>,
- <0>; /* Do Nothing */
-};
-
-&saradc {
- compatible = "amlogic,meson-gxbb-saradc", "amlogic,meson-saradc";
- clocks = <&xtal>,
- <&clkc CLKID_SAR_ADC>,
- <&clkc CLKID_SAR_ADC_CLK>,
- <&clkc CLKID_SAR_ADC_SEL>;
- clock-names = "clkin", "core", "adc_clk", "adc_sel";
-};
-
-&sd_emmc_a {
- clocks = <&clkc CLKID_SD_EMMC_A>,
- <&clkc CLKID_SD_EMMC_A_CLK0>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- resets = <&reset RESET_SD_EMMC_A>;
-};
-
-&sd_emmc_b {
- clocks = <&clkc CLKID_SD_EMMC_B>,
- <&clkc CLKID_SD_EMMC_B_CLK0>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- resets = <&reset RESET_SD_EMMC_B>;
-};
-
-&sd_emmc_c {
- clocks = <&clkc CLKID_SD_EMMC_C>,
- <&clkc CLKID_SD_EMMC_C_CLK0>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- resets = <&reset RESET_SD_EMMC_C>;
-};
-
-&simplefb_hdmi {
- clocks = <&clkc CLKID_HDMI_PCLK>,
- <&clkc CLKID_CLK81>,
- <&clkc CLKID_GCLK_VENCI_INT0>;
-};
-
-&spicc {
- clocks = <&clkc CLKID_SPICC>;
- clock-names = "core";
- resets = <&reset RESET_PERIPHS_SPICC>;
- num-cs = <1>;
-};
-
-&spifc {
- clocks = <&clkc CLKID_SPI>;
-};
-
-&uart_A {
- clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
-};
-
-&uart_AO {
- clocks = <&xtal>, <&clkc_AO CLKID_AO_UART1>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
-};
-
-&uart_AO_B {
- clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
-};
-
-&uart_B {
- clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
-};
-
-&uart_C {
- clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
-};
-
-&vpu {
- compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
- power-domains = <&pwrc PWRC_GXBB_VPU_ID>;
-};
-
-&vdec {
- compatible = "amlogic,gxbb-vdec", "amlogic,gx-vdec";
- clocks = <&clkc CLKID_DOS_PARSER>,
- <&clkc CLKID_DOS>,
- <&clkc CLKID_VDEC_1>,
- <&clkc CLKID_VDEC_HEVC>;
- clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc";
- resets = <&reset RESET_PARSER>;
- reset-names = "esparser";
-};
Since meson-gxbb based boards switched to using upstream DT, so drop redundant files from arch/arm/dts directory. Only *-u-boot.dtsi files kept in arch/arm/dts directory for these boards. Signed-off-by: Sumit Garg <sumit.garg@linaro.org> --- arch/arm/dts/Makefile | 8 - arch/arm/dts/meson-gxbb-kii-pro.dts | 140 ---- arch/arm/dts/meson-gxbb-nanopi-k2.dts | 415 ------------ arch/arm/dts/meson-gxbb-odroidc2.dts | 418 ------------ arch/arm/dts/meson-gxbb-p200.dts | 100 --- arch/arm/dts/meson-gxbb-p201.dts | 26 - arch/arm/dts/meson-gxbb-p20x.dtsi | 250 ------- arch/arm/dts/meson-gxbb-wetek-hub.dts | 58 -- arch/arm/dts/meson-gxbb-wetek-play2.dts | 119 ---- arch/arm/dts/meson-gxbb-wetek.dtsi | 292 -------- arch/arm/dts/meson-gxbb.dtsi | 856 ------------------------ 11 files changed, 2682 deletions(-) delete mode 100644 arch/arm/dts/meson-gxbb-kii-pro.dts delete mode 100644 arch/arm/dts/meson-gxbb-nanopi-k2.dts delete mode 100644 arch/arm/dts/meson-gxbb-odroidc2.dts delete mode 100644 arch/arm/dts/meson-gxbb-p200.dts delete mode 100644 arch/arm/dts/meson-gxbb-p201.dts delete mode 100644 arch/arm/dts/meson-gxbb-p20x.dtsi delete mode 100644 arch/arm/dts/meson-gxbb-wetek-hub.dts delete mode 100644 arch/arm/dts/meson-gxbb-wetek-play2.dts delete mode 100644 arch/arm/dts/meson-gxbb-wetek.dtsi delete mode 100644 arch/arm/dts/meson-gxbb.dtsi