diff --git a/doc/board/qualcomm/board.rst b/doc/board/qualcomm/board.rst
index 4d793209f9e3..003d59a18ebd 100644
--- a/doc/board/qualcomm/board.rst
+++ b/doc/board/qualcomm/board.rst
@@ -89,8 +89,13 @@ Or for db410c (and other boards not supported by the generic target)::
 
 	make CROSS_COMPILE=aarch64-linux-gnu- O=.output dragonboard410c_defconfig
 	make O=.output -j$(nproc)
 
+Or for smartphones::
+
+	make CROSS_COMPILE=aarch64-linux-gnu- O=.output qcom_defconfig qcom-phone.config
+	make O=.output -j$(nproc)
+
 - gzip u-boot::
 
 	gzip u-boot-nodtb.bin
 
diff --git a/doc/board/qualcomm/index.rst b/doc/board/qualcomm/index.rst
index 4955274a39bc..690d80c4ab1b 100644
--- a/doc/board/qualcomm/index.rst
+++ b/doc/board/qualcomm/index.rst
@@ -8,4 +8,5 @@ Qualcomm
 
    dragonboard410c
    board
    debugging
+   phones
diff --git a/doc/board/qualcomm/phones.rst b/doc/board/qualcomm/phones.rst
new file mode 100644
index 000000000000..0726f782b675
--- /dev/null
+++ b/doc/board/qualcomm/phones.rst
@@ -0,0 +1,122 @@
+.. SPDX-License-Identifier: GPL-2.0+
+.. sectionauthor:: Caleb Connolly <caleb.connolly@linaro.org>
+
+======================================
+Booting U-Boot on Qualcomm smartphones
+======================================
+
+About this
+----------
+
+This page attempts to the describe U-Boot support for Qualcomm phones, as a user guide but also a
+technical introduction to How Stuff Works to help new porters.
+
+In broad strokes, U-Boot should boot if the SoC is supported, and the device is already capable of
+booting an upstream Linux kernel.
+
+The list of supported Qualcomm SoCs changes often, for now it is best to look in
+``drivers/clk/qcom/`` to get a rough idea.
+
+For building instructions, see :doc:`board`.
+
+Phone bringup
+-------------
+
+It is usually easier to get Linux booting first, there are many good resources for this such as the
+`postmarketOS wiki`_. Once the device can boot Linux with logs on the display and ideally USB gadget
+support, it is highly likely that U-Boot will boot as well.
+
+For logs on display, you should have a simple framebuffer node defined in your DT, newer devices
+require that this follow the downstream naming scheme (that the DTB is compiled with labels enabled
+and the framebuffer reserved-memory region is labelled ``cont_splash``). Once this is working in
+Linux it should also work in U-Boot.
+
+In practise, U-Boot still has many more papercuts than Linux, which can be sticking points when
+porting a new device. In particular, drivers failing to bind/probe (especially pre-relocation) can
+be near-impossible to debug without UART since U-Boot will simply panic with no way to inform you of
+the error. As a result, bringing up a new device can be quite frustrating, but there are quite a few
+things you can try.
+
+The phone config
+^^^^^^^^^^^^^^^^
+
+Since most phones lack a physical keyboard or serial port, a special config fragment and environment
+file can be used to provide a more seamless experience. This can be enabled by generating the config
+with::
+
+	make CROSS_COMPILE=aarch64-linux-gnu- O=.output qcom_defconfig qcom-phone.config
+
+The config and associated environment file can be found in board/qualcomm/. The main changes are:
+
+- Panic on hang (so the panic message can be read on the display)
+- Boot retry (to automatically open and re-open the bootmenu)
+- A boot menu with helpful shortcuts (including USB console gadget)
+- Launch the boot menu if power is held during boot or on boot failure
+
+Hang/crash bisection
+--------------------
+
+Without a way to get logs, we can still get quite far with only a few bits of information: what
+happens when you ``fastboot boot u-boot.img``?
+
+Does the device disconnect?
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+This can be verified by watching ``dmesg -w``. It likely means the boot image doesn't match what the
+bootloader expected, use ``unpack_bootimg`` to compare it with a known-good boot image (ideally one
+with an upstream kernel).
+
+Does the device hang?
+^^^^^^^^^^^^^^^^^^^^^
+
+Since ``qcom-phone.config`` enables CONFIG_PANIC_HANG, this likely means that you're successfully
+executing U-Boot code (yay!), but something is causing a panic.
+
+It could also be due to a bad memory or register access triggering a secure interrupt, it's worth
+waiting for around a minute to see if the device eventually reboots or goes to crashdump mode. You
+can also disable CONFIG_PANIC_HANG and see if that causes the device to reboot instead, if so then
+it is definitely a U-Boot panic.
+
+With enough time and patience, it should be possible to narrow down the cause of the panic by
+inserting calls to ``reset_cpu()``. You can then determine where execution stops by seeing if the
+device hangs or resets.
+
+A good place to start is ``board_fdt_blob_setup()`` in ``arch/arm/mach-snapdragon/board.c``, this
+function is called extremely early so adding a reset call is a good way to validate that U-Boot is
+definitely running.
+
+You can then do a binary search starting from the end of ``board_init_f()`` / start of
+``board_init_r()`` and work from there using the init sequences for reference.
+
+The Qualcomm RAM parsing code is a likely culprit, as ABL is known to sometimes give bogus entries
+in the memory node which can trip U-Boot up. We should eventually handle all of these correctly
+upstream.
+
+To rule out crashes that might be caused by specific drivers, it's a good idea to disable them and
+re-enable them one by one. Here is a non-exhaustive list of drivers to disable:
+
+- pinctrl
+- mmc
+- scsi/ufs
+- usb (dwc3)
+- phy
+- clk (remove clock references from your framebuffer node in DT)
+
+Ideally, it would be possible to use the framebuffer as an early console / debug output, at the time
+of writing there are out of tree patches for this but they haven't been submitted upstream yet.
+
+Does the device reboot or go to crashdump mode?
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+On many devices crashdump mode is disabled, so they will reboot instead (maybe after some delay).
+The same approach as suggested above can be used to figure out where the crash occurs.
+
+If the device is rebooting, you can insert calls to ``hang()`` instead of ``reset_cpu()`` when
+following the instructions above.
+
+The most likely cause of a crashdump is the pinctrl/gpio driver or the SMMU driver, ensure that the
+``apps_smmu`` node in your SoCs devicetree file has one of its compatible strings referenced in
+``drivers/iommu/qcom-hyp-smmu.c``, you can also try disabling the pinctrl driver for your SoC (or
+``CONFIG_PINCTRL`` altogether).
+
+.. _`postmarketOS wiki`: https://wiki.postmarketos.org/wiki/Mainlining
