Message ID | 20240418125609.3867730-2-quic_rajkbhag@quicinc.com |
---|---|
State | New |
Headers | show |
Series | wifi: ath12k: Add support to set mlo_capable_flags from QMI PHY capability | expand |
On 4/18/2024 5:56 AM, Raj Kumar Bhagat wrote: > New parameter 'single_chip_mlo_support' was added in QMI PHY > capability response message. This is an optional parameter added > in QCN9274 firmware. This parameter states if the firmware > supports Single-Link Operation (SLO) and Multi-Link Operation (MLO) > within the same device. > > If single_chip_mlo_support = 1, then intra device SLO/MLO is supported > in the firmware. > If single_chip_mlo_support = 0, then intra device SLO/MLO is not > supported in the firmware. > > Hence, add support to read 'single_chip_mlo_support' parameter from > the QMI PHY capability response message. > > Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 > Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 > > Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> wrote: > New parameter 'single_chip_mlo_support' was added in QMI PHY > capability response message. This is an optional parameter added > in QCN9274 firmware. This parameter states if the firmware > supports Single-Link Operation (SLO) and Multi-Link Operation (MLO) > within the same device. > > If single_chip_mlo_support = 1, then intra device SLO/MLO is supported > in the firmware. > If single_chip_mlo_support = 0, then intra device SLO/MLO is not > supported in the firmware. > > Hence, add support to read 'single_chip_mlo_support' parameter from > the QMI PHY capability response message. > > Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 > Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 > > Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> > Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> 2 patches applied to ath-next branch of ath.git, thanks. ae6ec4a38aa4 wifi: ath12k: read single_chip_mlo_support parameter from QMI PHY capability da3cbd88e780 wifi: ath12k: set mlo_capable_flags based on QMI PHY capability
diff --git a/drivers/net/wireless/ath/ath12k/qmi.c b/drivers/net/wireless/ath/ath12k/qmi.c index db8ba5fec2ae..a555839dae8e 100644 --- a/drivers/net/wireless/ath/ath12k/qmi.c +++ b/drivers/net/wireless/ath/ath12k/qmi.c @@ -582,6 +582,24 @@ static const struct qmi_elem_info qmi_wlanfw_phy_cap_resp_msg_v01_ei[] = { .offset = offsetof(struct qmi_wlanfw_phy_cap_resp_msg_v01, board_id), }, + { + .data_type = QMI_OPT_FLAG, + .elem_len = 1, + .elem_size = sizeof(u8), + .array_type = NO_ARRAY, + .tlv_type = 0x13, + .offset = offsetof(struct qmi_wlanfw_phy_cap_resp_msg_v01, + single_chip_mlo_support_valid), + }, + { + .data_type = QMI_UNSIGNED_1_BYTE, + .elem_len = 1, + .elem_size = sizeof(u8), + .array_type = NO_ARRAY, + .tlv_type = 0x13, + .offset = offsetof(struct qmi_wlanfw_phy_cap_resp_msg_v01, + single_chip_mlo_support), + }, { .data_type = QMI_EOTI, .array_type = NO_ARRAY, @@ -2160,9 +2178,11 @@ static void ath12k_qmi_phy_cap_send(struct ath12k_base *ab) ab->qmi.num_radios = resp.num_phy; - ath12k_dbg(ab, ATH12K_DBG_QMI, "phy capability resp valid %d num_phy %d valid %d board_id %d\n", + ath12k_dbg(ab, ATH12K_DBG_QMI, + "phy capability resp valid %d num_phy %d valid %d board_id %d valid %d single_chip_mlo_support %d\n", resp.num_phy_valid, resp.num_phy, - resp.board_id_valid, resp.board_id); + resp.board_id_valid, resp.board_id, + resp.single_chip_mlo_support_valid, resp.single_chip_mlo_support); return; diff --git a/drivers/net/wireless/ath/ath12k/qmi.h b/drivers/net/wireless/ath/ath12k/qmi.h index 6ee33c9851c6..f7a5eb11ce44 100644 --- a/drivers/net/wireless/ath/ath12k/qmi.h +++ b/drivers/net/wireless/ath/ath12k/qmi.h @@ -265,6 +265,8 @@ struct qmi_wlanfw_phy_cap_resp_msg_v01 { u8 num_phy; u8 board_id_valid; u32 board_id; + u8 single_chip_mlo_support_valid; + u8 single_chip_mlo_support; }; #define QMI_WLANFW_IND_REGISTER_REQ_MSG_V01_MAX_LEN 54
New parameter 'single_chip_mlo_support' was added in QMI PHY capability response message. This is an optional parameter added in QCN9274 firmware. This parameter states if the firmware supports Single-Link Operation (SLO) and Multi-Link Operation (MLO) within the same device. If single_chip_mlo_support = 1, then intra device SLO/MLO is supported in the firmware. If single_chip_mlo_support = 0, then intra device SLO/MLO is not supported in the firmware. Hence, add support to read 'single_chip_mlo_support' parameter from the QMI PHY capability response message. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> --- drivers/net/wireless/ath/ath12k/qmi.c | 24 ++++++++++++++++++++++-- drivers/net/wireless/ath/ath12k/qmi.h | 2 ++ 2 files changed, 24 insertions(+), 2 deletions(-)