| Message ID | 20230508142308.1656410-1-bryan.odonoghue@linaro.org |
|---|---|
| Headers | show |
| Series | Add Qualcomm PMIC TPCM support | expand |
On Mon, 08 May 2023 15:23:01 +0100, Bryan O'Donoghue wrote: > Add the PMIC Type-C port driver to the list of devices. > > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> > --- > Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml | 4 ++++ > 1 file changed, 4 insertions(+) > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: ./Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml: Unable to find schema file matching $id: http://devicetree.org/schemas/usb/qcom,pmic-typec.yaml See https://patchwork.ozlabs.org/patch/1778444 This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit.
I'm dropping the previous V1-V6 log because the text is getting too long here's a link to the previous cover letter instead Link: https://lore.kernel.org/linux-arm-msm/20230501121111.1058190-1-bryan.odonoghue@linaro.org/ Bootable tree Link: https://git.codelinaro.org/bryan.odonoghue/kernel/-/tree/linux-next-23-05-07-pm8150b-tcpm-qcom-wrapper-typec-mux-bjorn Please note patch#5 and patch#6 should be merged in tandem not separately. V7: - Adds R/B to "dt-bindings: phy: qcom,sc7180-qmp-usb3-dp-phy: Add input and output ports" - Krzysztof - Fixes indicated, adds R/B to "dt-bindings: usb: Add Qualcomm PMIC Type-C" - Krzysztof - Fixes indicated, adds R/B to "usb: typec: qcom: Add Qualcomm PMIC Type-C driver" - Guenter - Fixes indicated, adds R/B to "usb: typec: qcom: Add Qualcomm PMIC Type-C driver" - Caleb - Adds R/B to "arm64: dts: qcom: sm8250: Define ports for qmpphy orientation-switching" - Konrad - Adds R/B to "arm64: dts: qcom: qrb5165-rb5: Switch on Type-C VBUS boost" - Konrad - Fixes indicated, adds R/B to "arm64: dts: qcom: qrb5165-rb5: Switch on basic TCPM" - Jianhua, Konrad - Connector ports/endpoints left inside of connector Documentation/devicetree/bindings/connector/usb-connector.yaml - Jianhua - dwc3_role_switch_in -> usb_1_dwc3_role_switch_in qmpphy_typec_mux_in -> usb_1_qmpphy_typec_mux_in Both ports/endpoints defined inside of pm8150b dtsi - Konrad I modified the name of both so that the port/endpoint would be directly adjacent to the containing node in the dtsi file for code locality/readbility - bod - Fixes newline indicated "arm64: dts: qcom: qrb5165-rb5: Switch on TCPM usb-role-switching for usb_1" - Jianhua, Konrad - Fixes newline indicated "arm64: dts: qcom: qrb5165-rb5: Switch on TCPM orientation-switch for usb_1_qmpphy" - Jianhua, Konrad - connector I have left the connector defintion and its ports/endpoints in the platform dts The reason for this a) Prior art e.g. arch/arm64/boot/dts/qcom/sc8280xp* b) The connector is really a non-SoC/PMIC component its something that is defined for your platform. I'm open to further debate on this topic: Link: https://imgflip.com/i/7kw6ck - port@1 -> port@1 "arm64: dts: qcom: qrb5165-rb5: Switch on TCPM orientation-switch for usb_1_qmpphy" - Jianhua - OF: graph: no port node found in /soc@0/spmi@c440000/pmic@2/typec@1500 I left this as-is since the DT model we want is to connect the connector directly to the PHY for orientation or controller for data-role switching I similarly didn't put this hack in place to remove the warning but "it would work" &pm8150b_typec { status = "okay"; + ports { + port@0 { + reg = <0>; + }; + }; + - Fairphone4 / sm7225 pm7250b is a derivative of pm8150b I have the hardware but, haven't booted to test/debug on this hardware yet - RB3 / sdm845 Caleb has a WIP patchset based on this series which is our next likely upstream candidate Here's how I'm testing using an RB5/SM8250 A) Confirm device mode works in both orientations - Boot to a Linux shell - Run usb-ecm-up.sh [1] - This provides usb0 on the device side @ 192.168.8.2 - Attach Type-C cable to host PC - On host PC "sudo ifconfig usb0 192.168.8.1" - Ping 192.168.8.2 confirming ping works - Switch cable orientation - On the PC side re-assign the ip address "sudo ifconfig usb0 192.168.8.1" - Ping again confirming connectivity B) Test automatic host-mode transition, orientation and SuperSpeed - Remove cable from PC - Attach a Type-C USB key - Validate the orientation detection cat /sys/class/typec/port0/orientation normal - Confirm the RB5 sees the USB key as a SuperSpeed device - Remove USB key and physically invert it along the horizontal axis - Re-insert the key - Confirm the RB5 sees the USB key as a SuperSpeed device - Validate the orientation detection cat /sys/class/typec/port0/orientation reverse C) Test Type-C accessory automatic host-mode transition, orientation and SuperSpeed - Remove USB key from RB5 - Attach a Type-C USB accessory - Validate the orientation detection cat /sys/class/typec/port0/orientation normal - Attach a SuperSpeed capable USB key to the Type-C accessory - Confirm the RB5 sees the USB key as a SuperSpeed device - Remove the USB key from the Type-C accessory - Remove the Type-C accessory from the RB5 - Physically invert the Type-C accessory along the horizontal axis - Re-insert the Type-C accessory - Validate the orientation detection cat /sys/class/typec/port0/orientation reverse - Re-insert the key - Confirm the RB5 sees the USB key as a SuperSpeed device D) Goto Test-A - Confirming that automatic switch to device mode happens - Repeat the above loop in ~ any order [1] usb-ecm-up.sh #!/usr/bin/env bash # load libcomposite module modprobe libcomposite # ensure function is loaded modprobe usb_f_ecm modprobe usb_f_ncm mount -t configfs none /sys/kernel/config/ # create a gadget mkdir /sys/kernel/config/usb_gadget/g0 # cd to its configfs node cd /sys/kernel/config/usb_gadget/g0 # configure it (vid/pid can be anything if USB Class is used for driver compat) echo 0x0525 > idVendor echo 0xa4a4 > idProduct # configure its serial/mfg/product mkdir strings/0x409 echo 0xCAFEBABE > strings/0x409/serialnumber echo Linaro > strings/0x409/manufacturer echo qrb5165-rb5 > strings/0x409/product # create configs mkdir configs/c.1 mkdir configs/c.1/strings/0x409 # create the function (name must match a usb_f_<name> module such as 'acm') mkdir functions/ncm.0 echo "CDC ECM" > configs/c.1/strings/0x409/configuration # associate function with config ln -s functions/ncm.0 configs/c.1 # Set USB version 3.1 echo 0x0310 > bcdUSB echo "super-speed-plus" > max_speed # enable gadget by binding it to a UDC from /sys/class/udc echo a600000.usb > UDC # to unbind it: echo "" > UDC; sleep 1; rm -rf /sys/kernel/config/usb_gadget/g0 sleep 1 ifconfig usb0 192.168.8.2 Bryan O'Donoghue (13): dt-bindings: regulator: qcom,usb-vbus-regulator: Mark reg as required dt-bindings: regulator: qcom,usb-vbus-regulator: Mark regulator-*-microamp required dt-bindings: phy: qcom,sc7180-qmp-usb3-dp-phy: Add orientation-switch as optional dt-bindings: phy: qcom,sc7180-qmp-usb3-dp-phy: Add input and output ports dt-bindings: usb: Add Qualcomm PMIC Type-C dt-bindings: mfd: qcom,spmi-pmic: Add typec to SPMI device types usb: typec: qcom: Add Qualcomm PMIC Type-C driver arm64: dts: qcom: sm8250: Define ports for qmpphy orientation-switching arm64: dts: qcom: pm8150b: Add a TCPM description arm64: dts: qcom: qrb5165-rb5: Switch on Type-C VBUS boost arm64: dts: qcom: qrb5165-rb5: Switch on basic TCPM arm64: dts: qcom: qrb5165-rb5: Switch on TCPM usb-role-switching for usb_1 arm64: dts: qcom: qrb5165-rb5: Switch on TCPM orientation-switch for usb_1_qmpphy .../bindings/mfd/qcom,spmi-pmic.yaml | 4 + .../phy/qcom,sc7180-qmp-usb3-dp-phy.yaml | 44 ++ .../regulator/qcom,usb-vbus-regulator.yaml | 10 +- .../bindings/usb/qcom,pmic-typec.yaml | 190 ++++++ MAINTAINERS | 10 + arch/arm64/boot/dts/qcom/pm8150b.dtsi | 40 ++ arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 54 +- arch/arm64/boot/dts/qcom/sm8250.dtsi | 18 + drivers/usb/typec/Kconfig | 13 - drivers/usb/typec/Makefile | 1 - drivers/usb/typec/qcom-pmic-typec.c | 261 -------- drivers/usb/typec/tcpm/Kconfig | 11 + drivers/usb/typec/tcpm/Makefile | 1 + drivers/usb/typec/tcpm/qcom/Makefile | 6 + drivers/usb/typec/tcpm/qcom/qcom_pmic_typec.c | 346 +++++++++++ .../typec/tcpm/qcom/qcom_pmic_typec_pdphy.c | 528 +++++++++++++++++ .../typec/tcpm/qcom/qcom_pmic_typec_pdphy.h | 119 ++++ .../typec/tcpm/qcom/qcom_pmic_typec_port.c | 556 ++++++++++++++++++ .../typec/tcpm/qcom/qcom_pmic_typec_port.h | 195 ++++++ 19 files changed, 2130 insertions(+), 277 deletions(-) create mode 100644 Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml delete mode 100644 drivers/usb/typec/qcom-pmic-typec.c create mode 100644 drivers/usb/typec/tcpm/qcom/Makefile create mode 100644 drivers/usb/typec/tcpm/qcom/qcom_pmic_typec.c create mode 100644 drivers/usb/typec/tcpm/qcom/qcom_pmic_typec_pdphy.c create mode 100644 drivers/usb/typec/tcpm/qcom/qcom_pmic_typec_pdphy.h create mode 100644 drivers/usb/typec/tcpm/qcom/qcom_pmic_typec_port.c create mode 100644 drivers/usb/typec/tcpm/qcom/qcom_pmic_typec_port.h