diff mbox series

[v3,1/2] usb: dwc3: add Realtek DHC RTD SoC dwc3 glue layer driver

Message ID 20230810055440.3534-1-stanley_chang@realtek.com
State Superseded
Headers show
Series [v3,1/2] usb: dwc3: add Realtek DHC RTD SoC dwc3 glue layer driver | expand

Commit Message

Stanley Chang[昌育德] Aug. 10, 2023, 5:54 a.m. UTC
Realtek DHC RTD SoCs integrate dwc3 IP and has some customizations to
support different generations of SoCs.

Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
---
v2 to v3 change:
    Remove the support_drd_mode of struct dwc3_rtk.
    Remove unlink_usb3_port and disable_usb3_phy.
    Disabled usb3 phy if the max speed is not super-speed.
v1 to v2 change:
    Remove the the code about the property realtek,enable-l4icg.
    Select USB_ROLE_SWITCH in Kconfig.
    Add dependency OF and ARCH_REALTEK in Kconfig.
---
 drivers/usb/dwc3/Kconfig    |  11 +
 drivers/usb/dwc3/Makefile   |   1 +
 drivers/usb/dwc3/dwc3-rtk.c | 482 ++++++++++++++++++++++++++++++++++++
 3 files changed, 494 insertions(+)
 create mode 100644 drivers/usb/dwc3/dwc3-rtk.c

Comments

Rob Herring Aug. 10, 2023, 8:36 p.m. UTC | #1
On Thu, Aug 10, 2023 at 01:54:35PM +0800, Stanley Chang wrote:
> Document the DWC3 USB bindings for Realtek SoCs.
> 
> Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
> ---
> v2 to v3 change:
>     Add description for reg
>     Remove property for realtek,unlink-usb3-port.
>     Remove property for realtek,disable-usb3-phy.
>     Use the maximum-speed instead of the above two properties.
> v1 to v2 change:
>     Revise the subject.
>     Rename the file.
>     Fix dtschema warnings.
>     Remove the property realtek,enable-l4icg.
>     Drop status.
> ---
>  .../bindings/usb/realtek,rtd-dwc3.yaml        | 80 +++++++++++++++++++
>  1 file changed, 80 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/realtek,rtd-dwc3.yaml
> 
> diff --git a/Documentation/devicetree/bindings/usb/realtek,rtd-dwc3.yaml b/Documentation/devicetree/bindings/usb/realtek,rtd-dwc3.yaml
> new file mode 100644
> index 000000000000..cc66adc4b9da
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/realtek,rtd-dwc3.yaml
> @@ -0,0 +1,80 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright 2023 Realtek Semiconductor Corporation
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/realtek,rtd-dwc3.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Realtek DWC3 USB SoC Controller Glue
> +
> +maintainers:
> +  - Stanley Chang <stanley_chang@realtek.com>
> +
> +description:
> +  The Realtek DHC SoC embeds a DWC3 USB IP Core configured for USB 2.0
> +  and USB 3.0 in host or dual-role mode.
> +
> +properties:
> +  compatible:
> +    items:
> +      - enum:
> +          - realtek,rtd1295-dwc3
> +          - realtek,rtd1315e-dwc3
> +          - realtek,rtd1319-dwc3
> +          - realtek,rtd1319d-dwc3
> +          - realtek,rtd1395-dwc3
> +          - realtek,rtd1619-dwc3
> +          - realtek,rtd1619b-dwc3
> +      - const: realtek,rtd-dwc3
> +
> +  reg:
> +    description: Offset and length of register set for wrapper of dwc3 core.
> +    maxItems: 1
> +
> +  '#address-cells':
> +    const: 1
> +
> +  '#size-cells':
> +    const: 1
> +
> +  ranges: true
> +
> +patternProperties:
> +  "^usb@[0-9a-f]+$":
> +    $ref: snps,dwc3.yaml#
> +    description: Required child node
> +
> +required:
> +  - compatible
> +  - reg
> +  - "#address-cells"
> +  - "#size-cells"
> +  - ranges
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    usb@98013e00 {
> +        compatible = "realtek,rtd1319d-dwc3", "realtek,rtd-dwc3";
> +        reg = <0x98013e00 0x200>;
> +        #address-cells = <1>;
> +        #size-cells = <1>;
> +        ranges;
> +        maximum-speed = "high-speed";

This should be a warning (the bot was having problems) as it is not 
defined for this node. It belongs in the child node as you also have, so 
drop it.

> +
> +        usb@98050000 {
> +            compatible = "snps,dwc3";
> +            reg = <0x98050000 0x9000>;
> +            interrupts = <0 94 4>;
> +            phys = <&usb2phy &usb3phy>;
> +            phy-names = "usb2-phy", "usb3-phy";
> +            dr_mode = "otg";
> +            usb-role-switch;
> +            role-switch-default-mode = "host";
> +            snps,dis_u2_susphy_quirk;
> +            snps,parkmode-disable-ss-quirk;
> +            snps,parkmode-disable-hs-quirk;
> +            maximum-speed = "high-speed";
> +        };
> +    };
> -- 
> 2.34.1
>
Stanley Chang[昌育德] Aug. 11, 2023, 5:58 a.m. UTC | #2
Hi Rob,

> > +
> > +examples:
> > +  - |
> > +    usb@98013e00 {
> > +        compatible = "realtek,rtd1319d-dwc3", "realtek,rtd-dwc3";
> > +        reg = <0x98013e00 0x200>;
> > +        #address-cells = <1>;
> > +        #size-cells = <1>;
> > +        ranges;
> > +        maximum-speed = "high-speed";
> 
> This should be a warning (the bot was having problems) as it is not defined for
> this node. It belongs in the child node as you also have, so drop it.

As I mentioned in the v1 patch, I have a problem.
This property maximum-speed belongs to dwc3.
When the dwc3-rtk setting disables USB 3.0 phy, dwc3 is not probed.
So I can't use api usb_get_maximum_speed(dev) to get maximum-speed.

I added this property "maximum-speed" to the dwc3-rtk node, which is the same as the dwc3 core node.
Is this configuration appropriate?
Or do you have any suggestion?

> > +
> > +        usb@98050000 {
> > +            compatible = "snps,dwc3";
> > +            reg = <0x98050000 0x9000>;
> > +            interrupts = <0 94 4>;
> > +            phys = <&usb2phy &usb3phy>;
> > +            phy-names = "usb2-phy", "usb3-phy";
> > +            dr_mode = "otg";
> > +            usb-role-switch;
> > +            role-switch-default-mode = "host";
> > +            snps,dis_u2_susphy_quirk;
> > +            snps,parkmode-disable-ss-quirk;
> > +            snps,parkmode-disable-hs-quirk;
> > +            maximum-speed = "high-speed";
> > +        };
> > +    };
> > --
> > 2.34.1
> >

Thanks,
Stanley
diff mbox series

Patch

diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
index 98efcbb76c88..5fc27b20df63 100644
--- a/drivers/usb/dwc3/Kconfig
+++ b/drivers/usb/dwc3/Kconfig
@@ -178,4 +178,15 @@  config USB_DWC3_OCTEON
 	  Only the host mode is currently supported.
 	  Say 'Y' or 'M' here if you have one such device.
 
+config USB_DWC3_RTK
+	tristate "Realtek DWC3 Platform Driver"
+	depends on OF && ARCH_REALTEK
+	default USB_DWC3
+	select USB_ROLE_SWITCH
+	help
+	  RTK DHC RTD SoCs with DesignWare Core USB3 IP inside,
+	  and IP Core configured for USB 2.0 and USB 3.0 in host
+	  or dual-role mode.
+	  Say 'Y' or 'M' if you have such device.
+
 endif
diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
index fe1493d4bbe5..124eda2522d9 100644
--- a/drivers/usb/dwc3/Makefile
+++ b/drivers/usb/dwc3/Makefile
@@ -55,3 +55,4 @@  obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
 obj-$(CONFIG_USB_DWC3_IMX8MP)		+= dwc3-imx8mp.o
 obj-$(CONFIG_USB_DWC3_XILINX)		+= dwc3-xilinx.o
 obj-$(CONFIG_USB_DWC3_OCTEON)		+= dwc3-octeon.o
+obj-$(CONFIG_USB_DWC3_RTK)		+= dwc3-rtk.o
diff --git a/drivers/usb/dwc3/dwc3-rtk.c b/drivers/usb/dwc3/dwc3-rtk.c
new file mode 100644
index 000000000000..72d43288b941
--- /dev/null
+++ b/drivers/usb/dwc3/dwc3-rtk.c
@@ -0,0 +1,482 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dwc3-rtk.c - Realtek DWC3 Specific Glue layer
+ *
+ * Copyright (C) 2023 Realtek Semiconductor Corporation
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/suspend.h>
+#include <linux/sys_soc.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/of.h>
+#include <linux/usb/role.h>
+
+#include "core.h"
+
+#define WRAP_CTR_REG  0x0
+#define DISABLE_MULTI_REQ BIT(1)
+#define DESC_R2W_MULTI_DISABLE BIT(9)
+#define FORCE_PIPE3_PHY_STATUS_TO_0 BIT(13)
+
+#define WRAP_USB2_PHY_UTMI_REG 0x8
+#define TXHSVM_EN BIT(3)
+
+#define WRAP_PHY_PIPE_REG 0xC
+#define RESET_DISABLE_PIPE3_P0 BIT(0)
+#define CLOCK_ENABLE_FOR_PIPE3_PCLK BIT(1)
+
+#define WRAP_USB_HMAC_CTR0_REG 0x60
+#define U3PORT_DIS BIT(8)
+
+#define WRAP_USB2_PHY_REG  0x70
+#define USB2_PHY_EN_PHY_PLL_PORT0 BIT(12)
+#define USB2_PHY_EN_PHY_PLL_PORT1 BIT(13)
+#define USB2_PHY_SWITCH_MASK 0x707
+#define USB2_PHY_SWITCH_DEVICE 0x0
+#define USB2_PHY_SWITCH_HOST 0x606
+
+#define WRAP_APHY_REG 0x128
+#define USB3_MBIAS_ENABLE BIT(1)
+
+#define WRAP_USB_DBUS_PWR_CTRL_REG 0x160
+#define DBUS_PWR_CTRL_EN BIT(0)
+
+struct dwc3_rtk {
+	struct device *dev;
+	void __iomem *regs;
+	size_t regs_size;
+
+	struct dwc3 *dwc;
+
+	int cur_dr_mode; /* current dr mode */
+	struct usb_role_switch *role_switch;
+};
+
+static void switch_usb2_dr_mode(struct dwc3_rtk *rtk, int dr_mode)
+{
+	switch (dr_mode) {
+	case USB_DR_MODE_PERIPHERAL:
+		writel(USB2_PHY_SWITCH_DEVICE |
+			    (~USB2_PHY_SWITCH_MASK &
+			      readl(rtk->regs + WRAP_USB2_PHY_REG)),
+			    rtk->regs + WRAP_USB2_PHY_REG);
+		break;
+	case USB_DR_MODE_HOST:
+		writel(USB2_PHY_SWITCH_HOST |
+			    (~USB2_PHY_SWITCH_MASK &
+			      readl(rtk->regs + WRAP_USB2_PHY_REG)),
+			    rtk->regs + WRAP_USB2_PHY_REG);
+		break;
+	default:
+		dev_dbg(rtk->dev, "%s: dr_mode=%d\n", __func__, dr_mode);
+		break;
+	}
+}
+
+static void switch_dwc3_dr_mode(struct dwc3_rtk *rtk, int dr_mode)
+{
+	if (!rtk->dwc->role_sw)
+		goto out;
+
+	switch (dr_mode) {
+	case USB_DR_MODE_PERIPHERAL:
+		usb_role_switch_set_role(rtk->dwc->role_sw, USB_ROLE_DEVICE);
+		break;
+	case USB_DR_MODE_HOST:
+		usb_role_switch_set_role(rtk->dwc->role_sw, USB_ROLE_HOST);
+		break;
+	default:
+		dev_dbg(rtk->dev, "%s dr_mode=%d\n", __func__, dr_mode);
+		break;
+	}
+
+out:
+	return;
+}
+
+static int dwc3_rtk_get_dr_mode(struct dwc3_rtk *rtk)
+{
+	enum usb_role role;
+
+	role = rtk->cur_dr_mode;
+
+	if (rtk->dwc && rtk->dwc->role_sw)
+		role = usb_role_switch_get_role(rtk->dwc->role_sw);
+	else
+		dev_dbg(rtk->dev, "%s not usb_role_switch role=%d\n", __func__, role);
+
+	return role;
+}
+
+static void dwc3_rtk_set_dr_mode(struct dwc3_rtk *rtk, int dr_mode)
+{
+	rtk->cur_dr_mode = dr_mode;
+
+	switch_dwc3_dr_mode(rtk, dr_mode);
+	mdelay(10);
+	switch_usb2_dr_mode(rtk, dr_mode);
+}
+
+#if IS_ENABLED(CONFIG_USB_ROLE_SWITCH)
+static int dwc3_usb_role_switch_set(struct usb_role_switch *sw, enum usb_role role)
+{
+	struct dwc3_rtk *rtk = usb_role_switch_get_drvdata(sw);
+
+	switch (role) {
+	case USB_ROLE_HOST:
+		dwc3_rtk_set_dr_mode(rtk, USB_DR_MODE_HOST);
+		break;
+	case USB_ROLE_DEVICE:
+		dwc3_rtk_set_dr_mode(rtk, USB_DR_MODE_PERIPHERAL);
+		break;
+	default:
+		dwc3_rtk_set_dr_mode(rtk, 0);
+	}
+
+	return 0;
+}
+
+static enum usb_role dwc3_usb_role_switch_get(struct usb_role_switch *sw)
+{
+	struct dwc3_rtk *rtk = usb_role_switch_get_drvdata(sw);
+	enum usb_role role = USB_ROLE_NONE;
+	int dr_mode;
+
+	dr_mode = dwc3_rtk_get_dr_mode(rtk);
+	switch (dr_mode) {
+	case USB_DR_MODE_HOST:
+		role = USB_ROLE_HOST;
+		break;
+	case USB_DR_MODE_PERIPHERAL:
+		role = USB_ROLE_DEVICE;
+		break;
+	default:
+		dev_dbg(rtk->dev, "%s dr_mode=%d", __func__, dr_mode);
+		break;
+	}
+	return role;
+}
+
+static int dwc3_rtk_setup_role_switch(struct dwc3_rtk *rtk)
+{
+	struct usb_role_switch_desc dwc3_role_switch = {NULL};
+
+	dwc3_role_switch.name = strchrnul(dev_name(rtk->dev), '.') + 1;
+	dwc3_role_switch.driver_data = rtk;
+	dwc3_role_switch.allow_userspace_control = true;
+	dwc3_role_switch.fwnode = dev_fwnode(rtk->dev);
+	dwc3_role_switch.set = dwc3_usb_role_switch_set;
+	dwc3_role_switch.get = dwc3_usb_role_switch_get;
+	rtk->role_switch = usb_role_switch_register(rtk->dev, &dwc3_role_switch);
+	if (IS_ERR(rtk->role_switch))
+		return PTR_ERR(rtk->role_switch);
+
+	return 0;
+}
+
+static int dwc3_rtk_remove_role_switch(struct dwc3_rtk *rtk)
+{
+	if (rtk->role_switch)
+		usb_role_switch_unregister(rtk->role_switch);
+
+	rtk->role_switch = NULL;
+
+	return 0;
+}
+#else
+#define dwc3_rtk_setup_role_switch(x) 0
+#define dwc3_rtk_remove_role_switch(x) 0
+#endif
+
+static int dwc3_rtk_init(struct dwc3_rtk *rtk)
+{
+	struct device *dev = rtk->dev;
+	void __iomem *regs = rtk->regs;
+	enum usb_device_speed maximum_speed;
+	const struct soc_device_attribute rtk_soc_kylin_a00[] = {
+		{ .family = "Realtek Kylin", .revision = "A00", },
+		{ /* empty */ } };
+	const struct soc_device_attribute rtk_soc_kylin[] = {
+		{ .family = "Realtek Kylin", }, { /* empty */ } };
+	const struct soc_device_attribute rtk_soc_hercules[] = {
+		{ .family = "Realtek Hercules", }, { /* empty */ } };
+	const struct soc_device_attribute rtk_soc_thor[] = {
+		{ .family = "Realtek Thor", }, { /* empty */ } };
+	const struct soc_device_attribute rtk_soc_hw_clock_gating_quirk[] = {
+		{ .family = "Realtek Kylin", },
+		{ .family = "Realtek Hercules", },
+		{ .family = "Realtek Thor", },
+		{ .family = "Realtek Hank", },
+		{ .family = "Realtek Groot", },
+		{ .family = "Realtek Stark", },
+		{ /* empty */ } };
+
+	if (soc_device_match(rtk_soc_kylin_a00)) {
+		writel(DISABLE_MULTI_REQ | readl(regs + WRAP_CTR_REG),
+		       regs + WRAP_CTR_REG);
+		dev_info(dev, "[bug fixed] 1295/1296 A00: add workaround to disable multiple request for D-Bus");
+	}
+
+	if (soc_device_match(rtk_soc_hercules)) {
+		writel(USB2_PHY_EN_PHY_PLL_PORT1 |
+		       readl(regs + WRAP_USB2_PHY_REG),
+		       regs + WRAP_USB2_PHY_REG);
+		dev_info(dev, "[bug fixed] 1395 add workaround to disable usb2 port 2 suspend!");
+	}
+
+	writel(TXHSVM_EN | readl(regs + WRAP_USB2_PHY_UTMI_REG),
+	       regs + WRAP_USB2_PHY_UTMI_REG);
+
+	maximum_speed = usb_get_maximum_speed(rtk->dev);
+	if (maximum_speed != USB_SPEED_UNKNOWN &&
+	    maximum_speed <= USB_SPEED_HIGH) {
+		void __iomem *reg;
+		int val;
+
+		if (soc_device_match(rtk_soc_thor)) {
+			reg =  rtk->regs + WRAP_USB_HMAC_CTR0_REG;
+			val = U3PORT_DIS | readl(reg);
+			writel(val, reg);
+		} else {
+			reg = rtk->regs + WRAP_CTR_REG;
+			val = FORCE_PIPE3_PHY_STATUS_TO_0 | readl(reg);
+			writel(val, reg);
+
+			reg = rtk->regs + WRAP_PHY_PIPE_REG;
+			val = ~CLOCK_ENABLE_FOR_PIPE3_PCLK & readl(reg);
+			val |= RESET_DISABLE_PIPE3_P0;
+			writel(val, reg);
+
+			reg =  rtk->regs + WRAP_USB_HMAC_CTR0_REG;
+			val = U3PORT_DIS | readl(reg);
+			writel(val, reg);
+
+			reg = rtk->regs + WRAP_APHY_REG;
+			val = ~USB3_MBIAS_ENABLE & readl(reg);
+			writel(val, reg);
+
+			dev_info(rtk->dev, "%s: disable usb 3.0 phy\n", __func__);
+		}
+	}
+
+	if (!soc_device_match(rtk_soc_kylin)) {
+		void __iomem *reg;
+		int val;
+
+		reg = rtk->regs + WRAP_USB_DBUS_PWR_CTRL_REG;
+		if (soc_device_match(rtk_soc_hw_clock_gating_quirk))
+			reg += 0x4;
+
+		val = DBUS_PWR_CTRL_EN | readl(reg);
+		writel(val, reg);
+	}
+
+	writel(DESC_R2W_MULTI_DISABLE | readl(regs + WRAP_CTR_REG),
+	       regs + WRAP_CTR_REG);
+
+	/* Set phy Dp/Dm initial state to host mode to avoid the Dp glitch */
+	writel(USB2_PHY_SWITCH_HOST |
+	       (~USB2_PHY_SWITCH_MASK &
+	       readl(rtk->regs + WRAP_USB2_PHY_REG)),
+	       rtk->regs + WRAP_USB2_PHY_REG);
+
+	return 0;
+}
+
+static int dwc3_rtk_probe_dwc3_core(struct dwc3_rtk *rtk)
+{
+	struct device *dev = rtk->dev;
+	struct device_node *node = dev->of_node;
+	struct platform_device *dwc3_pdev;
+	struct device *dwc3_dev;
+	struct device_node *dwc3_node;
+	int dr_mode;
+	int ret = 0;
+
+	ret = dwc3_rtk_init(rtk);
+	if (ret)
+		return -EINVAL;
+
+	ret = of_platform_populate(node, NULL, NULL, dev);
+	if (ret) {
+		dev_err(dev, "failed to add dwc3 core\n");
+		return ret;
+	}
+
+	dwc3_node = of_get_compatible_child(node, "snps,dwc3");
+	if (!dwc3_node) {
+		dev_err(dev, "failed to find dwc3 core node\n");
+		return -ENODEV;
+	}
+
+	dwc3_pdev = of_find_device_by_node(dwc3_node);
+	if (!dwc3_pdev) {
+		dev_err(dev, "failed to find dwc3 core platform_device\n");
+		of_node_put(dwc3_node);
+		return -ENODEV;
+	}
+
+	dwc3_dev = &dwc3_pdev->dev;
+	rtk->dwc = platform_get_drvdata(dwc3_pdev);
+	if (!rtk->dwc) {
+		dev_err(dev, "failed to find dwc3 core\n");
+		of_node_put(dwc3_node);
+		return -ENODEV;
+	}
+
+	dr_mode = usb_get_dr_mode(dwc3_dev);
+	if (dr_mode != rtk->dwc->dr_mode) {
+		dev_info(dev, "dts set dr_mode=%d, but dwc3 set dr_mode=%d\n",
+			 dr_mode, rtk->dwc->dr_mode);
+		dr_mode = rtk->dwc->dr_mode;
+	}
+
+	rtk->cur_dr_mode = dr_mode;
+
+	if (device_property_read_bool(dwc3_dev, "usb-role-switch")) {
+		ret = dwc3_rtk_setup_role_switch(rtk);
+		if (ret) {
+			dev_err(dev, "dwc3_rtk_setup_role_switch fail=%d\n", ret);
+			goto out;
+		}
+		rtk->cur_dr_mode = dwc3_rtk_get_dr_mode(rtk);
+	}
+
+	switch_usb2_dr_mode(rtk, rtk->cur_dr_mode);
+
+out:
+	of_node_put(dwc3_node);
+	platform_device_put(dwc3_pdev);
+
+	return ret;
+}
+
+static int dwc3_rtk_probe(struct platform_device *pdev)
+{
+	struct dwc3_rtk *rtk;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	void __iomem *regs;
+	int ret = 0;
+	unsigned long probe_time = jiffies;
+
+	rtk = devm_kzalloc(dev, sizeof(*rtk), GFP_KERNEL);
+	if (!rtk) {
+		ret = -ENOMEM;
+		goto err1;
+	}
+
+	platform_set_drvdata(pdev, rtk);
+
+	rtk->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "missing memory resource\n");
+		ret = -ENODEV;
+		goto err1;
+	}
+
+	regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(regs)) {
+		ret = PTR_ERR(regs);
+		goto err1;
+	}
+
+	rtk->regs = regs;
+	rtk->regs_size = resource_size(res);
+
+	ret = dwc3_rtk_probe_dwc3_core(rtk);
+	if (ret) {
+		dev_err(dev, "%s failed to add dwc3 core\n", __func__);
+		goto err1;
+	}
+
+	dev_dbg(dev, "%s ok! (take %d ms)\n", __func__,
+		jiffies_to_msecs(jiffies - probe_time));
+
+	return 0;
+
+err1:
+	return ret;
+}
+
+static void dwc3_rtk_remove(struct platform_device *pdev)
+{
+	struct dwc3_rtk *rtk = platform_get_drvdata(pdev);
+
+	rtk->dwc = NULL;
+
+	dwc3_rtk_remove_role_switch(rtk);
+
+	of_platform_depopulate(rtk->dev);
+}
+
+static void dwc3_rtk_shutdown(struct platform_device *pdev)
+{
+	struct dwc3_rtk *rtk = platform_get_drvdata(pdev);
+
+	of_platform_depopulate(rtk->dev);
+}
+
+static const struct of_device_id rtk_dwc3_match[] = {
+	{ .compatible = "realtek,rtd-dwc3" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, rtk_dwc3_match);
+
+#ifdef CONFIG_PM_SLEEP
+static int dwc3_rtk_suspend(struct device *dev)
+{
+	return 0;
+}
+
+static int dwc3_rtk_resume(struct device *dev)
+{
+	struct dwc3_rtk *rtk = dev_get_drvdata(dev);
+
+	dwc3_rtk_init(rtk);
+
+	switch_usb2_dr_mode(rtk, rtk->cur_dr_mode);
+
+	/* runtime set active to reflect active state. */
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
+	return 0;
+}
+
+static const struct dev_pm_ops dwc3_rtk_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(dwc3_rtk_suspend, dwc3_rtk_resume)
+};
+
+#define DEV_PM_OPS	(&dwc3_rtk_dev_pm_ops)
+#else
+#define DEV_PM_OPS	NULL
+#endif /* CONFIG_PM_SLEEP */
+
+static struct platform_driver dwc3_rtk_driver = {
+	.probe		= dwc3_rtk_probe,
+	.remove_new	= dwc3_rtk_remove,
+	.driver		= {
+		.name	= "rtk-dwc3",
+		.of_match_table = rtk_dwc3_match,
+		.pm	= DEV_PM_OPS,
+	},
+	.shutdown	= dwc3_rtk_shutdown,
+};
+
+module_platform_driver(dwc3_rtk_driver);
+
+MODULE_AUTHOR("Stanley Chang <stanley_chang@realtek.com>");
+MODULE_DESCRIPTION("DesignWare USB3 Realtek Glue Layer");
+MODULE_ALIAS("platform:rtk-dwc3");
+MODULE_LICENSE("GPL");
+MODULE_SOFTDEP("pre: phy_rtk_usb2 phy_rtk_usb3");