diff mbox series

[v2,net-next,7/8] net: phy: remove unnecessary line continuation

Message ID 1623837686-22569-8-git-send-email-liweihang@huawei.com
State New
Headers show
Series net: phy: fix some coding-style issues | expand

Commit Message

Weihang Li June 16, 2021, 10:01 a.m. UTC 
From: Wenpeng Liang <liangwenpeng@huawei.com>

Avoid unnecessary line continuations, and put '|' at the end of line.

Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
---
 drivers/net/phy/dp83640.c | 4 ++--
 drivers/net/phy/et1011c.c | 8 ++++----
 2 files changed, 6 insertions(+), 6 deletions(-)

Comments

Andrew Lunn June 16, 2021, 4:09 p.m. UTC | #1 
On Wed, Jun 16, 2021 at 06:01:25PM +0800, Weihang Li wrote:
> From: Wenpeng Liang <liangwenpeng@huawei.com>
> 
> Avoid unnecessary line continuations, and put '|' at the end of line.
> 
> Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
> Signed-off-by: Weihang Li <liweihang@huawei.com>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew
diff mbox series

Patch

diff --git a/drivers/net/phy/dp83640.c b/drivers/net/phy/dp83640.c
index 10769bf..705c166 100644
--- a/drivers/net/phy/dp83640.c
+++ b/drivers/net/phy/dp83640.c
@@ -170,9 +170,9 @@  static ushort gpio_tab[GPIO_TABLE_SIZE] = {
 module_param(chosen_phy, int, 0444);
 module_param_array(gpio_tab, ushort, NULL, 0444);
 
-MODULE_PARM_DESC(chosen_phy, \
+MODULE_PARM_DESC(chosen_phy,
 	"The address of the PHY to use for the ancillary clock features");
-MODULE_PARM_DESC(gpio_tab, \
+MODULE_PARM_DESC(gpio_tab,
 	"Which GPIO line to use for which purpose: cal,perout,extts1,...,extts6");
 
 static void dp83640_gpio_defaults(struct ptp_pin_desc *pd)
diff --git a/drivers/net/phy/et1011c.c b/drivers/net/phy/et1011c.c
index 07bb484..be1b71d 100644
--- a/drivers/net/phy/et1011c.c
+++ b/drivers/net/phy/et1011c.c
@@ -73,10 +73,10 @@  static int et1011c_read_status(struct phy_device *phydev)
 					ET1011C_GIGABIT_SPEED) {
 			val = phy_read(phydev, ET1011C_CONFIG_REG);
 			val &= ~ET1011C_TX_FIFO_MASK;
-			phy_write(phydev, ET1011C_CONFIG_REG, val\
-					| ET1011C_GMII_INTERFACE\
-					| ET1011C_SYS_CLK_EN\
-					| ET1011C_TX_FIFO_DEPTH_16);
+			phy_write(phydev, ET1011C_CONFIG_REG, val |
+					  ET1011C_GMII_INTERFACE |
+					  ET1011C_SYS_CLK_EN |
+					  ET1011C_TX_FIFO_DEPTH_16);
 
 		}
 	}