diff mbox series

[v2] Bluetooth: btusb: add support for Qualcomm WCN785x

Message ID 1650017516-28912-1-git-send-email-quic_zijuhu@quicinc.com
State Superseded
Headers show
Series [v2] Bluetooth: btusb: add support for Qualcomm WCN785x | expand

Commit Message

quic_zijuhu April 15, 2022, 10:11 a.m. UTC
Qualcomm WCN785x has PID/VID 0cf3/e700 as shown by
/sys/kernel/debug/usb/devices:

T:  Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  8 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e700 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms

Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
---
 drivers/bluetooth/btusb.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

Comments

Marcel Holtmann April 22, 2022, 9:16 a.m. UTC | #1
Hi Zijun,

> Qualcomm WCN785x has PID/VID 0cf3/e700 as shown by
> /sys/kernel/debug/usb/devices:
> 
> T:  Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  8 Spd=12   MxCh= 0
> D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
> P:  Vendor=0cf3 ProdID=e700 Rev= 0.01
> C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
> E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
> E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
> I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
> I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
> I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
> I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
> I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
> I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
> I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms
> 
> Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
> ---
> drivers/bluetooth/btusb.c | 10 ++++++++--
> 1 file changed, 8 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index 06a854a2507e..67a6a84a6f61 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -317,6 +317,11 @@ static const struct usb_device_id blacklist_table[] = {
> 						     BTUSB_WIDEBAND_SPEECH |
> 						     BTUSB_VALID_LE_STATES },
> 
> +	/* QCA WCN785x chipset */
> +	{ USB_DEVICE(0x0cf3, 0xe700), .driver_info = BTUSB_QCA_WCN6855 |
> +						     BTUSB_WIDEBAND_SPEECH |
> +						     BTUSB_VALID_LE_STATES },
> +
> 	/* Broadcom BCM2035 */
> 	{ USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
> 	{ USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
> @@ -3037,6 +3042,7 @@ static const struct qca_device_info qca_devices_table[] = {
> 	{ 0x00130100, 40, 4, 16 }, /* WCN6855 1.0 */
> 	{ 0x00130200, 40, 4, 16 }, /* WCN6855 2.0 */
> 	{ 0x00130201, 40, 4, 16 }, /* WCN6855 2.1 */
> +	{ 0x00190200, 40, 4, 16 }, /* WCN785x 2.0 */
> };
> 
> static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
> @@ -3327,11 +3333,11 @@ static int btusb_setup_qca(struct hci_dev *hdev)
> 		if (err < 0)
> 			return err;
> 
> -		/* WCN6855 2.1 will reset to apply firmware downloaded here, so
> +		/* WCN6855 2.1 and later will reset to apply firmware downloaded here, so
> 		 * wait ~100ms for reset Done then go ahead, otherwise, it maybe
> 		 * cause potential enable failure.
> 		 */
> -		if (info->rom_version == 0x00130201)
> +		if ((info->rom_version == 0x00130201) || (info->rom_version == 0x00190200))
> 			msleep(QCA_BT_RESET_WAIT_MS);

I think it is better to start using a switch statement here.

Regards

Marcel
quic_zijuhu April 26, 2022, 4:06 a.m. UTC | #2
On 4/22/2022 5:16 PM, Marcel Holtmann wrote:
> Hi Zijun,
> 
>> Qualcomm WCN785x has PID/VID 0cf3/e700 as shown by
>> /sys/kernel/debug/usb/devices:
>>
>> T:  Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  8 Spd=12   MxCh= 0
>> D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
>> P:  Vendor=0cf3 ProdID=e700 Rev= 0.01
>> C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
>> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
>> E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
>> E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
>> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
>> E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
>> I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
>> E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
>> I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
>> E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
>> I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
>> E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
>> I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
>> E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
>> I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
>> E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
>> I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
>> E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
>> I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
>> E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms
>>
>> Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
>> ---
>> drivers/bluetooth/btusb.c | 10 ++++++++--
>> 1 file changed, 8 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
>> index 06a854a2507e..67a6a84a6f61 100644
>> --- a/drivers/bluetooth/btusb.c
>> +++ b/drivers/bluetooth/btusb.c
>> @@ -317,6 +317,11 @@ static const struct usb_device_id blacklist_table[] = {
>> 						     BTUSB_WIDEBAND_SPEECH |
>> 						     BTUSB_VALID_LE_STATES },
>>
>> +	/* QCA WCN785x chipset */
>> +	{ USB_DEVICE(0x0cf3, 0xe700), .driver_info = BTUSB_QCA_WCN6855 |
>> +						     BTUSB_WIDEBAND_SPEECH |
>> +						     BTUSB_VALID_LE_STATES },
>> +
>> 	/* Broadcom BCM2035 */
>> 	{ USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
>> 	{ USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
>> @@ -3037,6 +3042,7 @@ static const struct qca_device_info qca_devices_table[] = {
>> 	{ 0x00130100, 40, 4, 16 }, /* WCN6855 1.0 */
>> 	{ 0x00130200, 40, 4, 16 }, /* WCN6855 2.0 */
>> 	{ 0x00130201, 40, 4, 16 }, /* WCN6855 2.1 */
>> +	{ 0x00190200, 40, 4, 16 }, /* WCN785x 2.0 */
>> };
>>
>> static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
>> @@ -3327,11 +3333,11 @@ static int btusb_setup_qca(struct hci_dev *hdev)
>> 		if (err < 0)
>> 			return err;
>>
>> -		/* WCN6855 2.1 will reset to apply firmware downloaded here, so
>> +		/* WCN6855 2.1 and later will reset to apply firmware downloaded here, so
>> 		 * wait ~100ms for reset Done then go ahead, otherwise, it maybe
>> 		 * cause potential enable failure.
>> 		 */
>> -		if (info->rom_version == 0x00130201)
>> +		if ((info->rom_version == 0x00130201) || (info->rom_version == 0x00190200))
>> 			msleep(QCA_BT_RESET_WAIT_MS);
> 
> I think it is better to start using a switch statement here.
> 
i have changed this condition as (info->rom_version >= 0x00130201) within v3 patch and mailed it.
> Regards
> 
> Marcel
>
diff mbox series

Patch

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 06a854a2507e..67a6a84a6f61 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -317,6 +317,11 @@  static const struct usb_device_id blacklist_table[] = {
 						     BTUSB_WIDEBAND_SPEECH |
 						     BTUSB_VALID_LE_STATES },
 
+	/* QCA WCN785x chipset */
+	{ USB_DEVICE(0x0cf3, 0xe700), .driver_info = BTUSB_QCA_WCN6855 |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+
 	/* Broadcom BCM2035 */
 	{ USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
 	{ USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
@@ -3037,6 +3042,7 @@  static const struct qca_device_info qca_devices_table[] = {
 	{ 0x00130100, 40, 4, 16 }, /* WCN6855 1.0 */
 	{ 0x00130200, 40, 4, 16 }, /* WCN6855 2.0 */
 	{ 0x00130201, 40, 4, 16 }, /* WCN6855 2.1 */
+	{ 0x00190200, 40, 4, 16 }, /* WCN785x 2.0 */
 };
 
 static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
@@ -3327,11 +3333,11 @@  static int btusb_setup_qca(struct hci_dev *hdev)
 		if (err < 0)
 			return err;
 
-		/* WCN6855 2.1 will reset to apply firmware downloaded here, so
+		/* WCN6855 2.1 and later will reset to apply firmware downloaded here, so
 		 * wait ~100ms for reset Done then go ahead, otherwise, it maybe
 		 * cause potential enable failure.
 		 */
-		if (info->rom_version == 0x00130201)
+		if ((info->rom_version == 0x00130201) || (info->rom_version == 0x00190200))
 			msleep(QCA_BT_RESET_WAIT_MS);
 	}