@@ -20,7 +20,7 @@ Copyright (C) 2021, Jiri Slaby
^^^^^^^^^^^^^^^
The Smartio/Industio/UPCI family Linux driver supports following multiport
- boards.
+ boards:
- 2 ports multiport board
CP-102U, CP-102UL, CP-102UF
@@ -63,10 +63,10 @@ Copyright (C) 2021, Jiri Slaby
GNU General Public License in this version. Please refer to GNU General
Public License announcement in each source code file for more detail.
- In Moxa's Web sites, you may always find latest driver at
+ In Moxa's Web sites, you may always find the latest driver at
https://www.moxa.com/.
- This version of driver can be installed as Loadable Module (Module driver)
+ This version of driver can be installed as a Loadable Module (Module driver)
or built-in into kernel (Static driver). Before you install the driver,
please refer to hardware installation procedure in the User's Manual.
@@ -89,9 +89,9 @@ Copyright (C) 2021, Jiri Slaby
PCI/UPCI board
--------------
- You may need to adjust IRQ usage in BIOS to avoid from IRQ conflict
- with other ISA devices. Please refer to hardware installation
- procedure in User's Manual in advance.
+ You may need to adjust IRQ usage in BIOS to avoid IRQ conflict with other
+ ISA devices. Please refer to hardware installation procedure in User's
+ Manual in advance.
PCI IRQ Sharing
---------------
@@ -132,7 +132,7 @@ msdiag - Diagnostic
===================
This utility provides the function to display what Moxa Smartio/Industio
- board found by driver in the system.
+ board was found by the driver in the system.
msmon - Port Monitoring
=======================
@@ -162,23 +162,23 @@ msterm - Terminal Emulation
Supported Setserial parameters are listed as below.
- ============== =========================================================
- uart set UART type(16450-->disable FIFO, 16550A-->enable FIFO)
- close_delay set the amount of time(in 1/100 of a second) that DTR
+ ============== =============================================================
+ uart set UART type(16450 --> disable FIFO, 16550A --> enable FIFO)
+ close_delay set the amount of time (in 1/100 of a second) that DTR
should be kept low while being closed.
- closing_wait set the amount of time(in 1/100 of a second) that the
+ closing_wait set the amount of time (in 1/100 of a second) that the
serial port should wait for data to be drained while
- being closed, before the receiver is disable.
- spd_hi Use 57.6kb when the application requests 38.4kb.
- spd_vhi Use 115.2kb when the application requests 38.4kb.
- spd_shi Use 230.4kb when the application requests 38.4kb.
- spd_warp Use 460.8kb when the application requests 38.4kb.
- spd_normal Use 38.4kb when the application requests 38.4kb.
- spd_cust Use the custom divisor to set the speed when the
+ being closed, before the receiver is disabled.
+ spd_hi Use 57.6kb when the application requests 38.4kb.
+ spd_vhi Use 115.2kb when the application requests 38.4kb.
+ spd_shi Use 230.4kb when the application requests 38.4kb.
+ spd_warp Use 460.8kb when the application requests 38.4kb.
+ spd_normal Use 38.4kb when the application requests 38.4kb.
+ spd_cust Use the custom divisor to set the speed when the
application requests 38.4kb.
- divisor This option set the custom division.
- baud_base This option set the base baud rate.
- ============== =========================================================
+ divisor This option sets the custom division.
+ baud_base This option sets the base baud rate.
+ ============== =============================================================
6. Troubleshooting
^^^^^^^^^^^^^^^^^^
Fix some typos in the mxser's documentation. Signed-off-by: Jiri Slaby <jslaby@suse.cz> --- .../driver-api/serial/moxa-smartio.rst | 42 +++++++++---------- 1 file changed, 21 insertions(+), 21 deletions(-)