diff mbox series

[v2,09/14] dts: qcs404-evb: Add ethernet controller node

Message ID 20230201135901.482671-10-sumit.garg@linaro.org
State Accepted
Commit de8f42c93a9e714a45f012f87860a8bdaee6cfb9
Headers show
Series QCS404: Add ethernet and I2C drivers | expand

Commit Message

Sumit Garg Feb. 1, 2023, 1:58 p.m. UTC
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
---
 arch/arm/dts/qcs404-evb.dts | 98 ++++++++++++++++++++++++++++++++++++-
 1 file changed, 97 insertions(+), 1 deletion(-)

Comments

Tom Rini Feb. 10, 2023, 6:44 p.m. UTC | #1
On Wed, Feb 01, 2023 at 07:28:56PM +0530, Sumit Garg wrote:

> Signed-off-by: Sumit Garg <sumit.garg@linaro.org>

Applied to u-boot/master, thanks!
diff mbox series

Patch

diff --git a/arch/arm/dts/qcs404-evb.dts b/arch/arm/dts/qcs404-evb.dts
index cc70afa4c8..2de0e7537b 100644
--- a/arch/arm/dts/qcs404-evb.dts
+++ b/arch/arm/dts/qcs404-evb.dts
@@ -36,7 +36,7 @@ 
 		ranges = <0x0 0x0 0x0 0xffffffff>;
 		compatible = "simple-bus";
 
-		pinctrl_north@1300000 {
+		soc_gpios: pinctrl_north@1300000 {
 			compatible = "qcom,qcs404-pinctrl";
 			reg = <0x1300000 0x200000>;
 			gpio-controller;
@@ -48,6 +48,61 @@ 
 				pins = "GPIO_17", "GPIO_18";
 				function = "blsp_uart2";
 			};
+
+			ethernet_defaults: ethernet-defaults {
+				int {
+					pins = "GPIO_61";
+					function = "rgmii_int";
+					bias-disable;
+					drive-strength = <2>;
+				};
+				mdc {
+					pins = "GPIO_76";
+					function = "rgmii_mdc";
+					bias-pull-up;
+				};
+				mdio {
+					pins = "GPIO_75";
+					function = "rgmii_mdio";
+					bias-pull-up;
+				};
+				tx {
+					pins = "GPIO_67", "GPIO_66", "GPIO_65", "GPIO_64";
+					function = "rgmii_tx";
+					bias-pull-up;
+					drive-strength = <16>;
+				};
+				rx {
+					pins = "GPIO_73", "GPIO_72", "GPIO_71", "GPIO_70";
+					function = "rgmii_rx";
+					bias-disable;
+					drive-strength = <2>;
+				};
+				tx-ctl {
+					pins = "GPIO_68";
+					function = "rgmii_ctl";
+					bias-pull-up;
+					drive-strength = <16>;
+				};
+				rx-ctl {
+					pins = "GPIO_74";
+					function = "rgmii_ctl";
+					bias-disable;
+					drive-strength = <2>;
+				};
+				tx-ck {
+					pins = "GPIO_63";
+					function = "rgmii_ck";
+					bias-pull-up;
+					drive-strength = <16>;
+				};
+				rx-ck {
+					pins = "GPIO_69";
+					function = "rgmii_ck";
+					bias-disable;
+					drive-strength = <2>;
+				};
+			};
 		};
 
 		gcc: clock-controller@1800000 {
@@ -172,6 +227,47 @@ 
 			};
 		};
 
+		ethernet: ethernet@7a80000 {
+			compatible = "qcom,qcs404-ethqos";
+			reg = <0x07a80000 0x10000>,
+				<0x07a96000 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+			clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";
+			clocks = <&gcc GCC_ETH_AXI_CLK>,
+				 <&gcc GCC_ETH_SLAVE_AHB_CLK>,
+				 <&gcc GCC_ETH_PTP_CLK>,
+				 <&gcc GCC_ETH_RGMII_CLK>;
+
+			resets = <&reset GCC_EMAC_BCR>;
+			reset-names = "emac";
+
+			snps,tso;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			snps,reset-gpio = <&soc_gpios 60 GPIO_ACTIVE_LOW>;
+			snps,reset-active-low;
+			snps,reset-delays-us = <0 10000 10000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&ethernet_defaults>;
+
+			phy-handle = <&phy1>;
+			phy-mode = "rgmii";
+			max-speed = <1000>;
+
+			mdio {
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				compatible = "snps,dwmac-mdio";
+				phy1: phy@3 {
+					compatible = "ethernet-phy-ieee802.3-c22";
+					device_type = "ethernet-phy";
+					reg = <0x3>;
+				};
+			};
+		};
+
 		spmi@200f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x200f000 0x1000