@@ -773,7 +773,6 @@ hall_sensor_default: hall-sensor-default-state {
function = "gpio";
drive-strength = <2>;
bias-disable;
- input-enable;
};
tri_state_key_default: tri-state-key-default-state {
@@ -802,7 +801,6 @@ panel_te_pin: panel-te-state {
function = "mdp_vsync";
drive-strength = <2>;
bias-disable;
- input-enable;
};
panel_esd_pin: panel-esd-state {
@@ -810,7 +808,6 @@ panel_esd_pin: panel-esd-state {
function = "gpio";
drive-strength = <2>;
bias-pull-down;
- input-enable;
};
speaker_default: speaker-default-state {
@@ -608,7 +608,6 @@ ts_int_active: ts-int-active-state {
function = "gpio";
drive-strength = <8>;
bias-pull-up;
- input-enable;
};
ts_int_suspend: ts-int-suspend-state {
@@ -616,7 +615,6 @@ ts_int_suspend: ts-int-suspend-state {
function = "gpio";
drive-strength = <2>;
bias-pull-down;
- input-enable;
};
ts_reset_active: ts-reset-active-state {
@@ -80,7 +80,6 @@ wcd_intr_default: wcd-intr-default-state {
pins = "gpio54";
function = "gpio";
- input-enable;
bias-pull-down;
drive-strength = <2>;
};
@@ -586,7 +586,6 @@ ts_int_default: ts-int-default-state {
function = "gpio";
bias-pull-down;
drive-strength = <16>;
- input-enable;
};
ts_reset_sleep: ts-reset-sleep-state {
@@ -601,7 +600,6 @@ ts_int_sleep: ts-int-sleep-state {
function = "gpio";
bias-pull-down;
drive-strength = <2>;
- input-enable;
};
sde_dsi_active: sde-dsi-active-state {
@@ -3174,7 +3174,6 @@ quat_mi2s_sleep: quat-mi2s-sleep-state {
function = "gpio";
drive-strength = <2>;
bias-pull-down;
- input-enable;
};
quat_mi2s_active: quat-mi2s-active-state {
@@ -3190,7 +3189,6 @@ quat_mi2s_sd0_sleep: quat-mi2s-sd0-sleep-state {
function = "gpio";
drive-strength = <2>;
bias-pull-down;
- input-enable;
};
quat_mi2s_sd0_active: quat-mi2s-sd0-active-state {
@@ -3205,7 +3203,6 @@ quat_mi2s_sd1_sleep: quat-mi2s-sd1-sleep-state {
function = "gpio";
drive-strength = <2>;
bias-pull-down;
- input-enable;
};
quat_mi2s_sd1_active: quat-mi2s-sd1-active-state {
@@ -3220,7 +3217,6 @@ quat_mi2s_sd2_sleep: quat-mi2s-sd2-sleep-state {
function = "gpio";
drive-strength = <2>;
bias-pull-down;
- input-enable;
};
quat_mi2s_sd2_active: quat-mi2s-sd2-active-state {
@@ -3235,7 +3231,6 @@ quat_mi2s_sd3_sleep: quat-mi2s-sd3-sleep-state {
function = "gpio";
drive-strength = <2>;
bias-pull-down;
- input-enable;
};
quat_mi2s_sd3_active: quat-mi2s-sd3-active-state {
@@ -606,7 +606,6 @@ i2c3_hid_active: i2c2-hid-active-state {
pins = "gpio37";
function = "gpio";
- input-enable;
bias-pull-up;
drive-strength = <2>;
};
@@ -615,7 +614,6 @@ i2c5_hid_active: i2c5-hid-active-state {
pins = "gpio125";
function = "gpio";
- input-enable;
bias-pull-up;
drive-strength = <2>;
};
@@ -624,7 +622,6 @@ i2c11_hid_active: i2c11-hid-active-state {
pins = "gpio92";
function = "gpio";
- input-enable;
bias-pull-up;
drive-strength = <2>;
};
@@ -633,7 +630,6 @@ lid_pin_active: lid-pin-state {
pins = "gpio124";
function = "gpio";
- input-enable;
bias-disable;
};
@@ -641,7 +637,6 @@ mode_pin_active: mode-pin-state {
pins = "gpio95";
function = "gpio";
- input-enable;
bias-disable;
};
};
Pin configuration property "input-enable" was used with the intention to disable the output, but this is done by default by Linux drivers. Since patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not input-enable") the property is not accepted anymore. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi | 3 --- arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts | 2 -- arch/arm64/boot/dts/qcom/sdm845-wcd9340.dtsi | 1 - arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts | 2 -- arch/arm64/boot/dts/qcom/sdm845.dtsi | 5 ----- arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts | 5 ----- 6 files changed, 18 deletions(-)