Show patches with: Submitter = Jun Nie       |    State = Action Required       |    Archived = No       |   18 patches
Patch Series S/W/F Date Submitter Delegate State
imx: spl: Add weak reset_cpu() imx: spl: Add weak reset_cpu() --- 2022-10-25 Jun Nie New
rpi: Do not use dtb loaded by firmware rpi: Do not use dtb loaded by firmware --- 2018-11-08 Jun Nie New
[v3] sunxi: add support for Banana Pi M2 Zero board [v3] sunxi: add support for Banana Pi M2 Zero board --- 2018-06-06 Jun Nie New
[v2] sunxi: add support for Banana Pi M2 Zero board [v2] sunxi: add support for Banana Pi M2 Zero board --- 2018-05-24 Jun Nie New
fit: skip signature verification if board request fit: skip signature verification if board request --- 2018-04-11 Jun Nie New
common: build ymodem and s_record only on need common: build ymodem and s_record only on need --- 2018-02-11 Jun Nie New
sunxi: support fuse cmd to read/write fuse sunxi: support fuse cmd to read/write fuse --- 2018-01-27 Jun Nie New
[[PATCH,v2] 8/8] sunxi: H3: set different otg base address per mode [[PATCH,v2] 8/8] sunxi: H3: set different otg base address per mode --- 2018-01-05 Jun Nie New
[[PATCH,v2] 7/8] sunxi: usb_phy: setup USB PHY passby for USB0 on H3/H5/A64 [[PATCH,v2] 7/8] sunxi: usb_phy: setup USB PHY passby for USB0 on H3/H5/A64 --- 2018-01-05 Jun Nie New
[[PATCH,v2] 6/8] sunxi: usb_phy: Clear PHYCTL register before writing [[PATCH,v2] 6/8] sunxi: usb_phy: Clear PHYCTL register before writing --- 2018-01-05 Jun Nie New
[[PATCH,v2] 5/8] sunxi: musb: Enable OTG device clock for H3 [[PATCH,v2] 5/8] sunxi: musb: Enable OTG device clock for H3 --- 2018-01-05 Jun Nie New
[[PATCH,v2] 4/8] sunxi: musb: Hack dynamic fifo support for H3 OTG [[PATCH,v2] 4/8] sunxi: musb: Hack dynamic fifo support for H3 OTG --- 2018-01-05 Jun Nie New
[[PATCH,v2] 3/8] sunxi: Fix USB PHY index for H3/H5/A64 [[PATCH,v2] 3/8] sunxi: Fix USB PHY index for H3/H5/A64 --- 2018-01-05 Jun Nie New
[[PATCH,v2] 2/8] sunxi: musb: Add fifo config for H3 [[PATCH,v2] 2/8] sunxi: musb: Add fifo config for H3 --- 2018-01-05 Jun Nie New
[6/6] sunxi: Add initial Banana-Pi Zero support Add Bananapi Zero board with OTG supported --- 2018-01-05 Jun Nie New
[5/6] sunxi: usb_phy: Clear PHYCTL register before writing Add Bananapi Zero board with OTG supported --- 2018-01-05 Jun Nie New
[3/6] sunxi: musb: Enable OTG device clock for H3 Add Bananapi Zero board with OTG supported --- 2018-01-05 Jun Nie New
[1/6] sunxi: h3: add usb_otg and OHCI/EHCI for usbc0 on H3 Add Bananapi Zero board with OTG supported --- 2018-01-05 Jun Nie New